From: mturquette@baylibre.com (Michael Turquette)
To: linus-amlogic@lists.infradead.org
Subject: [PATCH RFC 3/3] ARM64: dts: meson-gxbb: use the new meson8b DWMAC glue
Date: Wed, 13 Jul 2016 14:01:14 -0700 [thread overview]
Message-ID: <146844367410.73491.117379762912178421@resonance> (raw)
In-Reply-To: <CAFBinCBcv+4MHe9sFeGLRRRvb7hjX4=XYOtxN_rO1yzVFZisaQ@mail.gmail.com>
Hi Martin,
Quoting Martin Blumenstingl (2016-06-27 04:33:49)
> On Mon, Jun 27, 2016 at 12:44 PM, Martin Blumenstingl
> <martin.blumenstingl@googlemail.com> wrote:
> > On Mon, Jun 27, 2016 at 11:24 AM, Carlo Caione <carlo@caione.org> wrote:
> >> A syscon is a region containing a set of miscellaneous registers used
> >> for several reasons by several devices [1]. It this case there is really
> >> no need to define a new syscon node since those two registers are only
> >> used by your driver.
> > I can easily change it back if that's the way to go.
> > Before I do that: could you please confirm that "mp2_clk_out" (which
> > is controlled by PRG_ETH0/offset 0x0 bits 7-9) is not something which
> > has to be available through the common clk framework?
> there was just an IRC discussion with Carlo on this topic:
> We tried to find whether PRG_ETH0 is used to actually configure
> "mp2_clk_out". Carlo brought up that it could also be the case that
> the ethernet block simply needs to be informed about the rate of the
> mp2_clk_out (which is *probably* the "mpll2" clock).
>
> I'm adding Michael Turquette to this mail, maybe you can comment on this topic.
>
> If it turns out that the etthernet block just has to know about the
> clock rate then we have two tasks:
> 1. identify why the mpll2 rate returns 0 on my GXBB device
This is in progress, but turns out it doesn't matter for Ethernet. Bit 4
in PRG_ETHERNET_ADDR0 control a mux clock inside of the Ethernet
controller.
A value of 0x0 selects fclk_div2 and a value of 0x1 selects mp2_clk_out.
The bootloader programs in sets the mux to zero, or fclk_div2 as the
input clock (which runs at 1GHz).
> 2. change my patch so the new DWMAC glue gets a reference to the mpll2
> clock and then use "clk_get_rate(mpll2) / (250 * 1000000)" to
> configure the PRG_ETH0_MP2_CLK bits.
Hmm, I'm not sure about that part. Bits 7-9 is a divider that further
divides the clock signal selected by bit 4. This is set to 0x4, which
means we divide the 1GHz fclk_div2 down to 250MHz, which seems to be the
expected value coming out of this divider.
I haven't looked further to see if there is a further programmable
divider to divide 250MHz down to 50MHz, or (more likely) there is simply
a fixed-factor divide-by-5 that results in the 50MHz rate consumed by
the PHY.
Modeling this all in the mmc driver makes sense. So we would have:
struct clk_mux clk_m250_sel ->
struct clk_divider clk_m250_div ->
struct clk_fixed_factor enet_phy_clk
I don't know what the name should be for that last one, I just chose
enet_phy_clk since it illustrates the point. The updated docs suggest
that clk_m250_{sel,div} might be reasonable names for the mux and
divider.
Kevin and I just got this info from AmLogic earlier today. The next rev
of documentation should correct these register definitions.
Regards,
Mike
next prev parent reply other threads:[~2016-07-13 21:01 UTC|newest]
Thread overview: 61+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-06-25 16:50 [RFC] meson: add support for configuring the ethernet clocks Martin Blumenstingl
2016-06-25 16:50 ` [PATCH RFC 1/3] net: dt-bindings: add the amlogic, meson8b-dwmac binding Martin Blumenstingl
2016-06-25 16:50 ` [PATCH RFC 2/3] net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC Martin Blumenstingl
2016-06-25 16:50 ` [PATCH RFC 3/3] ARM64: dts: meson-gxbb: use the new meson8b DWMAC glue Martin Blumenstingl
2016-06-27 9:24 ` Carlo Caione
2016-06-27 10:44 ` Martin Blumenstingl
2016-06-27 11:33 ` Martin Blumenstingl
2016-07-13 21:01 ` Michael Turquette [this message]
2016-07-13 21:22 ` Kevin Hilman
2016-08-15 16:40 ` [PATCH 0/3] ARM64: meson: Meson8b and GXBB DWMAC glue driver Martin Blumenstingl
2016-08-15 16:40 ` [PATCH 1/3] net: dt-bindings: Document the new Meson8b and GXBB DWMAC bindings Martin Blumenstingl
2016-08-16 14:25 ` Rob Herring
2016-08-15 16:40 ` [PATCH 2/3] net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC Martin Blumenstingl
2016-08-19 21:40 ` Kevin Hilman
2016-08-15 16:41 ` [PATCH 3/3] ARM64: dts: meson-gxbb: use the new GXBB DWMAC glue driver Martin Blumenstingl
2016-08-20 9:35 ` [PATCH v2 0/4] meson: Meson8b and " Martin Blumenstingl
2016-08-20 9:35 ` [PATCH v2 1/4] net: dt-bindings: Document the new Meson8b and GXBB DWMAC bindings Martin Blumenstingl
2016-08-22 11:55 ` Arnd Bergmann
2016-08-22 12:04 ` Martin Blumenstingl
2016-08-22 15:25 ` Arnd Bergmann
2016-08-28 16:15 ` Martin Blumenstingl
2016-08-29 13:31 ` Arnd Bergmann
2016-08-20 9:35 ` [PATCH v2 2/4] clk: gxbb: expose MPLL2 clock for use by DT Martin Blumenstingl
2016-08-20 9:35 ` [PATCH v2 3/4] net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC Martin Blumenstingl
2016-08-20 21:29 ` Joachim Eastwood
2016-08-21 12:00 ` Martin Blumenstingl
2016-08-20 9:35 ` [PATCH v2 4/4] ARM64: dts: meson-gxbb: use the new GXBB DWMAC glue driver Martin Blumenstingl
2016-08-28 16:16 ` [PATCH v3 0/5] meson: Meson8b and " Martin Blumenstingl
2016-08-28 16:16 ` [PATCH v3 1/5] net: dt-bindings: Document the new Meson8b and GXBB DWMAC bindings Martin Blumenstingl
2016-08-28 16:16 ` [PATCH v3 2/5] clk: gxbb: expose MPLL2 clock for use by DT Martin Blumenstingl
2016-08-28 16:16 ` [PATCH v3 3/5] stmmac: introduce get_stmmac_bsp_priv() helper Martin Blumenstingl
2016-08-28 16:16 ` [PATCH v3 4/5] net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC Martin Blumenstingl
2016-08-30 19:19 ` Stephen Boyd
2016-09-04 18:20 ` Martin Blumenstingl
2016-09-05 9:27 ` Arnd Bergmann
2016-08-28 16:16 ` [PATCH v3 5/5] ARM64: dts: meson-gxbb: use the new GXBB DWMAC glue driver Martin Blumenstingl
2016-08-29 3:40 ` [PATCH v3 0/5] meson: Meson8b and " David Miller
2016-08-30 18:49 ` Martin Blumenstingl
2016-08-31 4:57 ` David Miller
2016-09-02 4:23 ` Kevin Hilman
2016-09-02 5:37 ` David Miller
2016-09-02 8:50 ` Arnd Bergmann
2016-09-04 18:23 ` [PATCH v4 " Martin Blumenstingl
2016-09-04 18:23 ` [PATCH v4 1/5] net: dt-bindings: Document the new Meson8b and GXBB DWMAC bindings Martin Blumenstingl
2016-09-04 18:23 ` [PATCH v4 2/5] clk: gxbb: expose MPLL2 clock for use by DT Martin Blumenstingl
2016-09-04 18:23 ` [PATCH v4 3/5] stmmac: introduce get_stmmac_bsp_priv() helper Martin Blumenstingl
2016-09-04 18:23 ` [PATCH v4 4/5] net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC Martin Blumenstingl
2016-09-05 1:37 ` kbuild test robot
2016-09-05 10:53 ` Arnd Bergmann
2016-09-05 19:07 ` Martin Blumenstingl
2016-09-06 9:37 ` Arnd Bergmann
2016-09-05 1:43 ` kbuild test robot
2016-09-04 18:23 ` [PATCH v4 5/5] ARM64: dts: meson-gxbb: use the new GXBB DWMAC glue driver Martin Blumenstingl
2016-09-06 21:38 ` [PATCH v5 0/6] meson: Meson8b and " Martin Blumenstingl
2016-09-06 21:38 ` [PATCH v5 1/6] net: dt-bindings: Document the new Meson8b and GXBB DWMAC bindings Martin Blumenstingl
2016-09-06 21:38 ` [PATCH v5 2/6] clk: gxbb: expose MPLL2 clock for use by DT Martin Blumenstingl
2016-09-07 21:27 ` Stephen Boyd
2016-09-06 21:38 ` [PATCH v5 3/6] stmmac: introduce get_stmmac_bsp_priv() helper Martin Blumenstingl
2016-09-06 21:38 ` [PATCH v5 4/6] net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC Martin Blumenstingl
2016-09-06 21:38 ` [PATCH v5 5/6] ARM64: dts: meson-gxbb: use the new GXBB DWMAC glue driver Martin Blumenstingl
2016-09-06 21:38 ` [PATCH v5 6/6] net: stmmac: update the module description of the dwmac-meson driver Martin Blumenstingl
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=146844367410.73491.117379762912178421@resonance \
--to=mturquette@baylibre.com \
--cc=linus-amlogic@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®