From: martin.blumenstingl@googlemail.com (Martin Blumenstingl)
To: linus-amlogic@lists.infradead.org
Subject: [PATCH 0/4] Amlogic Meson SAR ADC support
Date: Wed, 11 Jan 2017 18:43:30 +0100 [thread overview]
Message-ID: <20170111174334.24343-1-martin.blumenstingl@googlemail.com> (raw)
This series add support for the SAR ADC on Amlogic Meson GXBB, GXL and
GXM SoCs.
The hardware on GXBB provides 10-bit ADC results, while GXL and GXM are
providing 12-bit results. Support for older SoCs (Meson8b and Meson8)
can be added with little effort, most of which is testing I guess (I
don't have any pre-GXBB hardware so I can't say).
A new set of clocks had to be added to the GXBB clock controller (used
by the GXBB/GXL/GXM SoCs) which are required to get the ADC working.
The ADC itself can sample multiple channels at the same time and allows
capturing multiple samples (which can be used for filtering/averaging).
The ADC results are stored inside a FIFO register. More details on what
the driver supports (or doesn't) can be found in the description of
patch #3.
The code is based on the public S805 (Meson8b) and S905 (GXBB)
datasheets, as well as by reading (various versions of) the vendor
driver and by inspecting the registers on the vendor kernels of my
testing-hardware.
Typical use-cases for the ADC on the Meson GX SoCs are:
- adc-keys ("ADC attached resistor ladder buttons")
- SoC temperature measurement (not supported by this driver yet as
the system firmware does this already and provides the values via the
SCPI protocol)
- "version-strapping" (different resistor values are used to indicate
the board-revision)
- and of course typical ADC measurements
Martin Blumenstingl (4):
Documentation: dt-bindings: add the Amlogic Meson SAR ADC
documentation
clk: gxbb: add the SAR ADC clocks and expose them
iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs
ARM64: dts: meson: meson-gx: add the SAR ADC
.../bindings/iio/adc/amlogic,meson-saradc.txt | 31 +
arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 8 +
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 10 +
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 10 +
drivers/clk/meson/gxbb.c | 48 ++
drivers/clk/meson/gxbb.h | 9 +-
drivers/iio/adc/Kconfig | 12 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/meson_saradc.c | 860 +++++++++++++++++++++
include/dt-bindings/clock/gxbb-clkc.h | 4 +
10 files changed, 990 insertions(+), 3 deletions(-)
create mode 100644 Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt
create mode 100644 drivers/iio/adc/meson_saradc.c
--
2.11.0
next reply other threads:[~2017-01-11 17:43 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-01-11 17:43 Martin Blumenstingl [this message]
2017-01-11 17:43 ` [PATCH 1/4] Documentation: dt-bindings: add the Amlogic Meson SAR ADC documentation Martin Blumenstingl
2017-01-11 17:43 ` [PATCH 2/4] clk: gxbb: add the SAR ADC clocks and expose them Martin Blumenstingl
2017-01-11 17:43 ` [PATCH 3/4] iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs Martin Blumenstingl
2017-01-14 14:46 ` Jonathan Cameron
2017-01-14 17:44 ` Martin Blumenstingl
2017-01-15 13:08 ` Jonathan Cameron
2017-01-15 12:26 ` Lars-Peter Clausen
2017-01-15 13:09 ` Jonathan Cameron
2017-01-11 17:43 ` [PATCH 4/4] ARM64: dts: meson: meson-gx: add the SAR ADC Martin Blumenstingl
2017-01-15 22:42 ` [PATCH v2 0/4] Amlogic Meson SAR ADC support Martin Blumenstingl
2017-01-15 22:42 ` [PATCH v2 1/4] Documentation: dt-bindings: add the Amlogic Meson SAR ADC documentation Martin Blumenstingl
2017-01-15 22:42 ` [PATCH v2 2/4] clk: gxbb: add the SAR ADC clocks and expose them Martin Blumenstingl
2017-01-15 22:42 ` [PATCH v2 3/4] iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs Martin Blumenstingl
2017-01-16 17:41 ` Peter Meerwald-Stadler
2017-01-15 22:42 ` [PATCH v2 4/4] ARM64: dts: meson: meson-gx: add the SAR ADC Martin Blumenstingl
2017-01-16 10:18 ` [PATCH v2 0/4] Amlogic Meson SAR ADC support Neil Armstrong
2017-01-19 14:58 ` [PATCH v3 " Martin Blumenstingl
2017-01-19 14:58 ` [PATCH v3 1/4] Documentation: dt-bindings: add the Amlogic Meson SAR ADC documentation Martin Blumenstingl
2017-01-21 12:39 ` Jonathan Cameron
2017-01-21 13:21 ` Andreas Färber
2017-01-21 20:56 ` Rob Herring
2017-01-21 23:10 ` Martin Blumenstingl
2017-01-22 12:30 ` Jonathan Cameron
2017-01-19 14:58 ` [PATCH v3 2/4] clk: gxbb: add the SAR ADC clocks and expose them Martin Blumenstingl
2017-01-19 19:13 ` Stephen Boyd
2017-01-20 15:46 ` Kevin Hilman
2017-01-19 14:58 ` [PATCH v3 3/4] iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs Martin Blumenstingl
2017-01-21 12:52 ` Jonathan Cameron
2017-01-19 14:58 ` [PATCH v3 4/4] ARM64: dts: meson: meson-gx: add the SAR ADC Martin Blumenstingl
2017-01-21 13:28 ` Andreas Färber
2017-01-21 12:37 ` [PATCH v3 0/4] Amlogic Meson SAR ADC support Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170111174334.24343-1-martin.blumenstingl@googlemail.com \
--to=martin.blumenstingl@googlemail.com \
--cc=linus-amlogic@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®