From: jbrunet@baylibre.com (Jerome Brunet)
To: linus-amlogic@lists.infradead.org
Subject: [PATCH 5/6] ARM64: dts: meson: add mmc clk gate pins
Date: Fri, 4 Aug 2017 20:08:15 +0200 [thread overview]
Message-ID: <20170804180816.18737-6-jbrunet@baylibre.com> (raw)
In-Reply-To: <20170804180816.18737-1-jbrunet@baylibre.com>
Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
.../arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi | 9 ++++--
.../boot/dts/amlogic/meson-gxbb-nanopi-k2.dts | 9 ++++--
.../boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 11 +++++---
.../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 8 ++++--
arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 9 ++++--
.../boot/dts/amlogic/meson-gxbb-vega-s95.dtsi | 9 ++++--
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 33 ++++++++++++++++++++++
.../dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts | 6 ++--
.../dts/amlogic/meson-gxl-s905x-libretech-cc.dts | 6 ++--
.../dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts | 9 ++++--
.../boot/dts/amlogic/meson-gxl-s905x-p212.dtsi | 9 ++++--
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 33 ++++++++++++++++++++++
.../arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 6 ++--
13 files changed, 126 insertions(+), 31 deletions(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi
index dc478d094c11..ac16096d095e 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi
@@ -161,7 +161,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -187,7 +188,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -205,7 +207,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-sd-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
index 5d59fd75cae7..919c956a204c 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
@@ -195,7 +195,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>, <&sdio_irq_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -221,7 +222,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -242,7 +244,8 @@
&sd_emmc_c {
status = "disabled";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-sd-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
index a1078b3e1c76..21cd94247f6c 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
@@ -51,7 +51,7 @@
/ {
compatible = "nexbox,a95x", "amlogic,meson-gxbb";
model = "NEXBOX A95X";
-
+
aliases {
serial0 = &uart_AO;
};
@@ -225,7 +225,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -246,7 +247,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -264,7 +266,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-sd-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index d147c853ab05..d2fac2f62a21 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -50,7 +50,7 @@
/ {
compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
model = "Hardkernel ODROID-C2";
-
+
aliases {
serial0 = &uart_AO;
};
@@ -253,7 +253,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -271,7 +272,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-sd-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
index 900a13cc24ee..738bb45fd07b 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
@@ -187,7 +187,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -213,7 +214,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -234,7 +236,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-sd-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
index 346753fb6324..8acd8d8b375a 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
@@ -155,7 +155,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins &sdio_irq_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -181,7 +182,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -198,7 +200,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-sd-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
index 9a1e478f80d5..cac7a5530c4f 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
@@ -383,6 +383,17 @@
};
};
+ emmc_clk_gate_pins: emmc_clk_gate {
+ mux {
+ groups = "BOOT_8";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "BOOT_8";
+ bias-pull-down;
+ };
+ };
+
nor_pins: nor {
mux {
groups = "nor_d",
@@ -421,6 +432,17 @@
};
};
+ sdcard_clk_gate_pins: sdcard_clk_gate {
+ mux {
+ groups = "CARD_2";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "CARD_2";
+ bias-pull-down;
+ };
+ };
+
sdio_pins: sdio {
mux {
groups = "sdio_d0",
@@ -433,6 +455,17 @@
};
};
+ sdio_clk_gate_pins: sdio_clk_gate {
+ mux {
+ groups = "GPIOX_5";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "GPIOX_5";
+ bias-pull-down;
+ };
+ };
+
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts
index 2a5804ce7f4b..068623e75fec 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts
@@ -123,7 +123,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -141,7 +142,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-sd-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
index 185d737f1549..0537b92cd226 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
@@ -137,7 +137,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -159,7 +160,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts
index 6633a5d8fdd3..cf3b6e7860a4 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts
@@ -182,7 +182,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -203,7 +204,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -221,7 +223,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-sd-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
index f3eea8e89d12..e2509a834a62 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
@@ -95,7 +95,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -116,7 +117,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -134,7 +136,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-sd-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
index 071eca074a91..c222f19fca3f 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
@@ -271,6 +271,17 @@
};
};
+ emmc_clk_gate_pins: emmc_clk_gate {
+ mux {
+ groups = "BOOT_8";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "BOOT_8";
+ bias-pull-down;
+ };
+ };
+
nor_pins: nor {
mux {
groups = "nor_d",
@@ -309,6 +320,17 @@
};
};
+ sdcard_clk_gate_pins: sdcard_clk_gate {
+ mux {
+ groups = "CARD_2";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "CARD_2";
+ bias-pull-down;
+ };
+ };
+
sdio_pins: sdio {
mux {
groups = "sdio_d0",
@@ -321,6 +343,17 @@
};
};
+ sdio_clk_gate_pins: sdio_clk_gate {
+ mux {
+ groups = "GPIOX_5";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "GPIOX_5";
+ bias-pull-down;
+ };
+ };
+
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
index 5f626d683088..ae988bdf1f92 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
@@ -168,7 +168,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -186,7 +187,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-sd-highspeed;
--
2.9.4
next prev parent reply other threads:[~2017-08-04 18:08 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-08-04 18:08 [PATCH 0/6] ARM64: dts: meson: update around mmc Jerome Brunet
2017-08-04 18:08 ` [PATCH 1/6] ARM64: dts: meson-gxbb: nanopi-k2: add card regulator settle times Jerome Brunet
2017-08-04 18:08 ` [PATCH 2/6] ARM64: dts: meson-gxl: libretech-cc: " Jerome Brunet
2017-08-04 18:08 ` [PATCH 3/6] ARM64: dts: meson-gxbb: p20x: enable sdcard UHS modes Jerome Brunet
2017-08-04 18:08 ` [PATCH 4/6] ARM64: dts: meson-gxbb: nanopi-k2: " Jerome Brunet
2017-08-07 21:45 ` Kevin Hilman
2017-08-04 18:08 ` Jerome Brunet [this message]
2017-08-04 18:08 ` [PATCH 6/6] ARM64: dts: meson: remove cap-sd-highspeed from emmc nodes Jerome Brunet
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170804180816.18737-6-jbrunet@baylibre.com \
--to=jbrunet@baylibre.com \
--cc=linus-amlogic@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®