From: Jerome Brunet <jbrunet@baylibre.com>
To: Kevin Hilman <khilman@baylibre.com>
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
patchwork-bot+notify@kernel.org,
linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
Jerome Brunet <jbrunet@baylibre.com>
Subject: [PATCH 0/6] arm64: dts: meson: mmc clean-up
Date: Thu, 18 Apr 2019 14:27:08 +0200 [thread overview]
Message-ID: <20190418122714.30805-1-jbrunet@baylibre.com> (raw)
The patchset is bunch of clean-up found while debugging meson mmc.
* The first 2 patches address the libretech-cc which actually uses 1.8v
eMMC modules.
* Patch 3 is a pin bias fixup depending on mmc pins.
* Patch 4 lower the mmc max frequencies on gx chips. It was not easy
to spot but, according to the datasheet, the maximum UHS rate
supported by these chips is 100MHz (SDR50). This explains why we
never really managed to get a stable SDR104. SDIO is limited to HS.
* Patch 5 adds missing pinctrl definition on the vim2
* Patch 6 remove hs400 from the supported modes of the vim2. This mode is
mode reliable enough with HW/SW ATM.
When/If the series on the mmc drivers goes through, I'll send the
following updates:
* Push odroid-c2 eMMC max rate from 100Mhz to 200Mhz. With the new tuning
method, this mode is finally stable on the OC2 (so far...)
* Enable SD UHS modes on the odroid-c2
* Enable SD UHS DDR50 on the nanopi k2
Jerome Brunet (6):
arm64: dts: meson: libretech-cc: set eMMC as removable
arm64: dts: meson: libretech-cc: switch eMMC to 1.8v
arm64: dts: meson: fix mmc pin bias
arm64: dts: meson: fix mmc v2 chips max frequencies
arm64: dts: meson: vim2: add missing clk-gate pinctrl
arm64: dts: meson: vim2: remove sd hs and hs400 modes from emmc
.../arm64/boot/dts/amlogic/meson-axg-s400.dts | 4 +--
arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 31 ++++++++++++----
.../boot/dts/amlogic/meson-gx-p23x-q20x.dtsi | 4 +--
.../boot/dts/amlogic/meson-gxbb-nanopi-k2.dts | 5 ++-
.../dts/amlogic/meson-gxbb-nexbox-a95x.dts | 2 +-
.../boot/dts/amlogic/meson-gxbb-p20x.dtsi | 2 +-
.../boot/dts/amlogic/meson-gxbb-vega-s95.dtsi | 4 +--
.../boot/dts/amlogic/meson-gxbb-wetek.dtsi | 4 +--
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 35 +++++++++++++------
.../boot/dts/amlogic/meson-gxl-s805x-p241.dts | 2 +-
.../amlogic/meson-gxl-s905x-libretech-cc.dts | 14 ++++----
.../amlogic/meson-gxl-s905x-nexbox-a95x.dts | 2 +-
.../dts/amlogic/meson-gxl-s905x-p212.dtsi | 4 +--
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 35 +++++++++++++------
.../dts/amlogic/meson-gxm-khadas-vim2.dts | 15 ++++----
.../boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 2 +-
.../boot/dts/amlogic/meson-gxm-rbox-pro.dts | 4 +--
17 files changed, 109 insertions(+), 60 deletions(-)
--
2.20.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
next reply other threads:[~2019-04-18 12:27 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-04-18 12:27 Jerome Brunet [this message]
2019-04-18 12:27 ` [PATCH 1/6] arm64: dts: meson: libretech-cc: set eMMC as removable Jerome Brunet
2019-04-18 20:21 ` Martin Blumenstingl
2019-04-18 12:27 ` [PATCH 2/6] arm64: dts: meson: libretech-cc: switch eMMC to 1.8v Jerome Brunet
2019-04-18 19:46 ` Martin Blumenstingl
2019-04-18 12:27 ` [PATCH 3/6] arm64: dts: meson: fix mmc pin bias Jerome Brunet
2019-04-18 12:27 ` [PATCH 4/6] arm64: dts: meson: fix mmc v2 chips max frequencies Jerome Brunet
2019-04-18 12:27 ` [PATCH 5/6] arm64: dts: meson: vim2: add missing clk-gate pinctrl Jerome Brunet
2019-04-18 20:21 ` Martin Blumenstingl
2019-04-18 12:27 ` [PATCH 6/6] arm64: dts: meson: vim2: remove sd hs and hs400 modes from emmc Jerome Brunet
2019-05-03 22:04 ` [PATCH 0/6] arm64: dts: meson: mmc clean-up Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190418122714.30805-1-jbrunet@baylibre.com \
--to=jbrunet@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=khilman@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=patchwork-bot+notify@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®