mirror of https://lore.kernel.org/linux-amlogic/
 help / color / mirror / Atom feed
From: Liang Yang <liang.yang@amlogic.com>
To: Miquel Raynal <miquel.raynal@bootlin.com>,
	<linux-mtd@lists.infradead.org>
Cc: Liang Yang <liang.yang@amlogic.com>,
	Rob Herring <robh+dt@kernel.org>,
	Richard Weinberger <richard@nod.at>,
	Vignesh Raghavendra <vigneshr@ti.com>,
	Jerome Brunet <jbrunet@baylibre.com>,
	Neil Armstrong <narmstrong@baylibre.com>,
	Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
	Kevin Hilman <khilman@baylibre.com>,
	Jianxin Pan <jianxin.pan@amlogic.com>,
	Victor Wan <victor.wan@amlogic.com>,
	XianWei Zhao <xianwei.zhao@amlogic.com>,
	Kelvin Zhang <kelvin.zhang@amlogic.com>,
	BiChao Zheng <bichao.zheng@amlogic.com>,
	YongHui Yu <yonghui.yu@amlogic.com>,
	<linux-arm-kernel@lists.infradead.org>,
	<linux-amlogic@lists.infradead.org>,
	<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>
Subject: [PATCH RESEND v2 1/2] mtd: rawnand: meson: discard the common MMC sub clock framework
Date: Thu, 17 Feb 2022 14:33:45 +0800	[thread overview]
Message-ID: <20220217063346.21691-2-liang.yang@amlogic.com> (raw)
In-Reply-To: <20220217063346.21691-1-liang.yang@amlogic.com>

EMMC and NAND have the same clock control register named 'SD_EMMC_CLOCK' which is
defined in EMMC port internally. bit0~5 of 'SD_EMMC_CLOCK' is the divider and
bit6~7 is the mux for fix pll and xtal.A common MMC and NAND sub-clock has been
implemented and can be used by the eMMC and NAND controller (which are mutually
exclusive anyway). Let's use this new clock.

Signed-off-by: Liang Yang <liang.yang@amlogic.com>
---
 drivers/mtd/nand/raw/meson_nand.c | 107 +++++++++++++++++-------------
 1 file changed, 61 insertions(+), 46 deletions(-)

diff --git a/drivers/mtd/nand/raw/meson_nand.c b/drivers/mtd/nand/raw/meson_nand.c
index ac3be92872d0..c5b892d38ea0 100644
--- a/drivers/mtd/nand/raw/meson_nand.c
+++ b/drivers/mtd/nand/raw/meson_nand.c
@@ -10,6 +10,7 @@
 #include <linux/dma-mapping.h>
 #include <linux/interrupt.h>
 #include <linux/clk.h>
+#include <linux/clk-provider.h>
 #include <linux/mtd/rawnand.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mfd/syscon.h>
@@ -19,6 +20,7 @@
 #include <linux/iopoll.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_address.h>
 #include <linux/sched/task_stack.h>
 
 #define NFC_REG_CMD		0x00
@@ -104,6 +106,9 @@
 
 #define PER_INFO_BYTE		8
 
+#define CLK_DIV_SHIFT		0
+#define CLK_DIV_WIDTH		6
+
 struct meson_nfc_nand_chip {
 	struct list_head node;
 	struct nand_chip nand;
@@ -151,15 +156,15 @@ struct meson_nfc {
 	struct nand_controller controller;
 	struct clk *core_clk;
 	struct clk *device_clk;
-	struct clk *phase_tx;
-	struct clk *phase_rx;
+	struct clk *nand_clk;
+	struct clk_divider nand_divider;
 
 	unsigned long clk_rate;
 	u32 bus_timing;
 
 	struct device *dev;
 	void __iomem *reg_base;
-	struct regmap *reg_clk;
+	void __iomem *sd_emmc_clock;
 	struct completion completion;
 	struct list_head chips;
 	const struct meson_nfc_data *data;
@@ -988,6 +993,8 @@ static const struct mtd_ooblayout_ops meson_ooblayout_ops = {
 static int meson_nfc_clk_init(struct meson_nfc *nfc)
 {
 	int ret;
+	struct clk_init_data init = {0};
+	struct clk_parent_data nfc_divider_parent_data[1];
 
 	/* request core clock */
 	nfc->core_clk = devm_clk_get(nfc->dev, "core");
@@ -1002,21 +1009,26 @@ static int meson_nfc_clk_init(struct meson_nfc *nfc)
 		return PTR_ERR(nfc->device_clk);
 	}
 
-	nfc->phase_tx = devm_clk_get(nfc->dev, "tx");
-	if (IS_ERR(nfc->phase_tx)) {
-		dev_err(nfc->dev, "failed to get TX clk\n");
-		return PTR_ERR(nfc->phase_tx);
-	}
-
-	nfc->phase_rx = devm_clk_get(nfc->dev, "rx");
-	if (IS_ERR(nfc->phase_rx)) {
-		dev_err(nfc->dev, "failed to get RX clk\n");
-		return PTR_ERR(nfc->phase_rx);
-	}
+	init.name = devm_kstrdup(nfc->dev, "nfc#div", GFP_KERNEL);
+	init.ops = &clk_divider_ops;
+	nfc_divider_parent_data[0].fw_name = __clk_get_name(nfc->device_clk);
+	init.parent_data = nfc_divider_parent_data;
+	init.num_parents = 1;
+	nfc->nand_divider.reg = nfc->sd_emmc_clock;
+	nfc->nand_divider.shift = CLK_DIV_SHIFT;
+	nfc->nand_divider.width = CLK_DIV_WIDTH;
+	nfc->nand_divider.hw.init = &init;
+	nfc->nand_divider.flags = CLK_DIVIDER_ONE_BASED |
+				  CLK_DIVIDER_ROUND_CLOSEST |
+				  CLK_DIVIDER_ALLOW_ZERO;
+
+	nfc->nand_clk = devm_clk_register(nfc->dev, &nfc->nand_divider.hw);
+	if (IS_ERR(nfc->nand_clk))
+		return PTR_ERR(nfc->nand_clk);
 
 	/* init SD_EMMC_CLOCK to sane defaults w/min clock rate */
-	regmap_update_bits(nfc->reg_clk,
-			   0, CLK_SELECT_NAND, CLK_SELECT_NAND);
+	writel(CLK_SELECT_NAND | readl(nfc->sd_emmc_clock),
+	       nfc->sd_emmc_clock);
 
 	ret = clk_prepare_enable(nfc->core_clk);
 	if (ret) {
@@ -1030,29 +1042,21 @@ static int meson_nfc_clk_init(struct meson_nfc *nfc)
 		goto err_device_clk;
 	}
 
-	ret = clk_prepare_enable(nfc->phase_tx);
-	if (ret) {
-		dev_err(nfc->dev, "failed to enable TX clock\n");
-		goto err_phase_tx;
-	}
-
-	ret = clk_prepare_enable(nfc->phase_rx);
+	ret = clk_prepare_enable(nfc->nand_clk);
 	if (ret) {
-		dev_err(nfc->dev, "failed to enable RX clock\n");
-		goto err_phase_rx;
+		dev_err(nfc->dev, "pre enable NFC divider fail\n");
+		goto err_nand_clk;
 	}
 
 	ret = clk_set_rate(nfc->device_clk, 24000000);
 	if (ret)
-		goto err_disable_rx;
+		goto err_disable_clk;
 
 	return 0;
 
-err_disable_rx:
-	clk_disable_unprepare(nfc->phase_rx);
-err_phase_rx:
-	clk_disable_unprepare(nfc->phase_tx);
-err_phase_tx:
+err_disable_clk:
+	clk_disable_unprepare(nfc->nand_clk);
+err_nand_clk:
 	clk_disable_unprepare(nfc->device_clk);
 err_device_clk:
 	clk_disable_unprepare(nfc->core_clk);
@@ -1061,8 +1065,7 @@ static int meson_nfc_clk_init(struct meson_nfc *nfc)
 
 static void meson_nfc_disable_clk(struct meson_nfc *nfc)
 {
-	clk_disable_unprepare(nfc->phase_rx);
-	clk_disable_unprepare(nfc->phase_tx);
+	clk_disable_unprepare(nfc->nand_clk);
 	clk_disable_unprepare(nfc->device_clk);
 	clk_disable_unprepare(nfc->core_clk);
 }
@@ -1370,11 +1373,31 @@ static const struct of_device_id meson_nfc_id_table[] = {
 };
 MODULE_DEVICE_TABLE(of, meson_nfc_id_table);
 
+static int meson_nfc_reg_resource(struct device *dev, struct meson_nfc *nfc)
+{
+	struct resource res;
+	void __iomem *base[2];
+	struct device_node *node = dev->of_node;
+	int i;
+
+	for (i = 0; i < 2; i++) {
+		if (of_address_to_resource(node, i, &res))
+			return -ENOENT;
+
+		base[i] = devm_ioremap_resource(dev, &res);
+		if (IS_ERR(base))
+			return PTR_ERR(base);
+	}
+	nfc->reg_base = base[0];
+	nfc->sd_emmc_clock = base[1];
+
+	return 0;
+}
+
 static int meson_nfc_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct meson_nfc *nfc;
-	struct resource *res;
 	int ret, irq;
 
 	nfc = devm_kzalloc(dev, sizeof(*nfc), GFP_KERNEL);
@@ -1388,20 +1411,12 @@ static int meson_nfc_probe(struct platform_device *pdev)
 	nand_controller_init(&nfc->controller);
 	INIT_LIST_HEAD(&nfc->chips);
 	init_completion(&nfc->completion);
-
 	nfc->dev = dev;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	nfc->reg_base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(nfc->reg_base))
-		return PTR_ERR(nfc->reg_base);
-
-	nfc->reg_clk =
-		syscon_regmap_lookup_by_phandle(dev->of_node,
-						"amlogic,mmc-syscon");
-	if (IS_ERR(nfc->reg_clk)) {
-		dev_err(dev, "Failed to lookup clock base\n");
-		return PTR_ERR(nfc->reg_clk);
+	ret = meson_nfc_reg_resource(dev, nfc);
+	if (ret) {
+		dev_err(dev, "Failed to get reg resource\n");
+		return ret;
 	}
 
 	irq = platform_get_irq(pdev, 0);
-- 
2.34.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

  reply	other threads:[~2022-02-17  6:34 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-02-17  6:33 [PATCH RESEND v2 0/2] refine the NFC " Liang Yang
2022-02-17  6:33 ` Liang Yang [this message]
2022-02-17 13:05   ` [PATCH RESEND v2 1/2] mtd: rawnand: meson: discard the common MMC sub " kernel test robot
2022-02-28 11:28   ` Jerome Brunet
2022-03-02  3:35     ` Liang.Yang
2022-03-11  8:28     ` Liang Yang
2022-02-17  6:33 ` [PATCH RESEND v2 2/2] dt-bindings: nand: meson: refine Amlogic NAND controller driver Liang Yang
2022-02-28 11:36   ` Jerome Brunet
2022-03-02  5:19     ` Liang.Yang
2022-03-02  8:42       ` Jerome Brunet
2022-03-02  9:57         ` Liang.Yang

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220217063346.21691-2-liang.yang@amlogic.com \
    --to=liang.yang@amlogic.com \
    --cc=bichao.zheng@amlogic.com \
    --cc=devicetree@vger.kernel.org \
    --cc=jbrunet@baylibre.com \
    --cc=jianxin.pan@amlogic.com \
    --cc=kelvin.zhang@amlogic.com \
    --cc=khilman@baylibre.com \
    --cc=linux-amlogic@lists.infradead.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mtd@lists.infradead.org \
    --cc=martin.blumenstingl@googlemail.com \
    --cc=miquel.raynal@bootlin.com \
    --cc=narmstrong@baylibre.com \
    --cc=richard@nod.at \
    --cc=robh+dt@kernel.org \
    --cc=victor.wan@amlogic.com \
    --cc=vigneshr@ti.com \
    --cc=xianwei.zhao@amlogic.com \
    --cc=yonghui.yu@amlogic.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®