From: kishon@ti.com (Kishon Vijay Abraham I)
To: linus-amlogic@lists.infradead.org
Subject: [PATCH v3 2/2] phy: meson: add USB2 PHY support for Meson GXL and GXM
Date: Tue, 9 May 2017 10:45:07 +0530 [thread overview]
Message-ID: <20f7a149-12b1-bf00-fe33-0adad31c436e@ti.com> (raw)
In-Reply-To: <cb2a1b5a-0508-066c-4482-519081eb73cf@codeaurora.org>
On Tuesday 09 May 2017 10:17 AM, Vivek Gautam wrote:
> Hi,
>
>
> On 05/08/2017 05:51 PM, Kishon Vijay Abraham I wrote:
>> Hi,
>>
>> On Thursday 04 May 2017 11:38 PM, Martin Blumenstingl wrote:
>>> Hi Kishon,
>>>
>>> On Mon, Apr 17, 2017 at 9:11 PM, Martin Blumenstingl
>>> <martin.blumenstingl@googlemail.com> wrote:
>>>> This adds a new driver for the USB2 PHYs found on Meson GXL and GXM SoCs
>>>> (both SoCs are using the same USB PHY register layout).
>>>>
>>>> The USB2 PHY is a simple PHY which only has a few registers to configure
>>>> the mode (host/device) and a reset register (to enable/disable the PHY).
>>>>
>>>> Unfortunately there are no datasheets available for this PHY. The driver
>>>> was written by reading the code from Amlogic's GPL kernel sources and
>>>> by analyzing the registers on an actual GXL and GXM device running the
>>>> kernel that was shipped on the boards I have.
>>>>
>>>> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>>>> ---
>>>> drivers/phy/Kconfig | 12 ++
>>>> drivers/phy/Makefile | 1 +
>>>> drivers/phy/phy-meson-gxl-usb2.c | 261
>>>> +++++++++++++++++++++++++++++++++++++++
>>>> 3 files changed, 274 insertions(+)
>>>> create mode 100644 drivers/phy/phy-meson-gxl-usb2.c
>>>>
>>>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>>>> index 005cadb7a3f8..fada8354c0fe 100644
>>>> --- a/drivers/phy/Kconfig
>>>> +++ b/drivers/phy/Kconfig
>>>> @@ -511,4 +511,16 @@ config PHY_MESON8B_USB2
>>>> and GXBB SoCs.
>>>> If unsure, say N.
>>>>
>>>> +config PHY_MESON_GXL_USB
>>>> + tristate "Meson GXL and GXM USB2 PHY drivers"
>>>> + default ARCH_MESON
>>>> + depends on OF && (ARCH_MESON || COMPILE_TEST)
>>>> + depends on USB_SUPPORT
>>>> + select GENERIC_PHY
>>>> + select REGMAP_MMIO
>>>> + help
>>>> + Enable this to support the Meson USB2 PHYs found in Meson
>>>> + GXL and GXM SoCs.
>>>> + If unsure, say N.
>>>> +
>>>> endmenu
>>>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>>>> index dd8f3b5d2918..4f5ede46b0b9 100644
>>>> --- a/drivers/phy/Makefile
>>>> +++ b/drivers/phy/Makefile
>>>> @@ -62,3 +62,4 @@ obj-$(CONFIG_PHY_CYGNUS_PCIE) +=
>>>> phy-bcm-cygnus-pcie.o
>>>> obj-$(CONFIG_ARCH_TEGRA) += tegra/
>>>> obj-$(CONFIG_PHY_NS2_PCIE) += phy-bcm-ns2-pcie.o
>>>> obj-$(CONFIG_PHY_MESON8B_USB2) += phy-meson8b-usb2.o
>>>> +obj-$(CONFIG_PHY_MESON_GXL_USB) += phy-meson-gxl-usb2.o
>>>> diff --git a/drivers/phy/phy-meson-gxl-usb2.c
>>>> b/drivers/phy/phy-meson-gxl-usb2.c
>>>> new file mode 100644
>>>> index 000000000000..f5fbd3c09542
>>>> --- /dev/null
>>>> +++ b/drivers/phy/phy-meson-gxl-usb2.c
>>>> @@ -0,0 +1,261 @@
>>>> +/*
>>>> + * Meson GXL and GXM USB2 PHY driver
>>>> + *
>>>> + * Copyright (C) 2017 Martin Blumenstingl
>>>> <martin.blumenstingl@googlemail.com>
>>>> + *
>>>> + * This program is free software; you can redistribute it and/or modify
>>>> + * it under the terms of the GNU General Public License version 2 as
>>>> + * published by the Free Software Foundation.
>>>> + *
>>>> + * You should have received a copy of the GNU General Public License
>>>> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
>>>> + */
>>>> +
>>>> +#include <linux/delay.h>
>>>> +#include <linux/io.h>
>>>> +#include <linux/module.h>
>>>> +#include <linux/of_device.h>
>>>> +#include <linux/regmap.h>
>>>> +#include <linux/phy/phy.h>
>>>> +#include <linux/platform_device.h>
>>>> +
>>>> +/* bits [31:27] are read-only */
>>>> +#define U2P_R0 0x0
>>>> + #define U2P_R0_BYPASS_SEL BIT(0)
>>>> + #define U2P_R0_BYPASS_DM_EN BIT(1)
>>>> + #define U2P_R0_BYPASS_DP_EN BIT(2)
>>>> + #define U2P_R0_TXBITSTUFF_ENH BIT(3)
>>>> + #define U2P_R0_TXBITSTUFF_EN BIT(4)
>>>> + #define U2P_R0_DM_PULLDOWN BIT(5)
>>>> + #define U2P_R0_DP_PULLDOWN BIT(6)
>>>> + #define U2P_R0_DP_VBUS_VLD_EXT_SEL BIT(7)
>>>> + #define U2P_R0_DP_VBUS_VLD_EXT BIT(8)
>>>> + #define U2P_R0_ADP_PRB_EN BIT(9)
>>>> + #define U2P_R0_ADP_DISCHARGE BIT(10)
>>>> + #define U2P_R0_ADP_CHARGE BIT(11)
>>>> + #define U2P_R0_DRV_VBUS BIT(12)
>>>> + #define U2P_R0_ID_PULLUP BIT(13)
>>>> + #define U2P_R0_LOOPBACK_EN_B BIT(14)
>>>> + #define U2P_R0_OTG_DISABLE BIT(15)
>>>> + #define U2P_R0_COMMON_ONN BIT(16)
>>>> + #define U2P_R0_FSEL_MASK GENMASK(19,
>>>> 17)
>>>> + #define U2P_R0_REF_CLK_SEL_MASK GENMASK(21,
>>>> 20)
>>>> + #define U2P_R0_POWER_ON_RESET BIT(22)
>>>> + #define U2P_R0_V_ATE_TEST_EN_B_MASK GENMASK(24,
>>>> 23)
>>>> + #define U2P_R0_ID_SET_ID_DQ BIT(25)
>>>> + #define U2P_R0_ATE_RESET BIT(26)
>>>> + #define U2P_R0_FSV_MINUS BIT(27)
>>>> + #define U2P_R0_FSV_PLUS BIT(28)
>>>> + #define U2P_R0_BYPASS_DM_DATA BIT(29)
>>>> + #define U2P_R0_BYPASS_DP_DATA BIT(30)
>>>> +
>>>> +#define U2P_R1 0x4
>>>> + #define U2P_R1_BURN_IN_TEST BIT(0)
>>>> + #define U2P_R1_ACA_ENABLE BIT(1)
>>>> + #define U2P_R1_DCD_ENABLE BIT(2)
>>>> + #define U2P_R1_VDAT_SRC_EN_B BIT(3)
>>>> + #define U2P_R1_VDAT_DET_EN_B BIT(4)
>>>> + #define U2P_R1_CHARGES_SEL BIT(5)
>>>> + #define U2P_R1_TX_PREEMP_PULSE_TUNE BIT(6)
>>>> + #define U2P_R1_TX_PREEMP_AMP_TUNE_MASK GENMASK(8, 7)
>>>> + #define U2P_R1_TX_RES_TUNE_MASK GENMASK(10, 9)
>>>> + #define U2P_R1_TX_RISE_TUNE_MASK GENMASK(12,
>>>> 11)
>>>> + #define U2P_R1_TX_VREF_TUNE_MASK GENMASK(16,
>>>> 13)
>>>> + #define U2P_R1_TX_FSLS_TUNE_MASK GENMASK(20,
>>>> 17)
>>>> + #define U2P_R1_TX_HSXV_TUNE_MASK GENMASK(22,
>>>> 21)
>>>> + #define U2P_R1_OTG_TUNE_MASK GENMASK(25,
>>>> 23)
>>>> + #define U2P_R1_SQRX_TUNE_MASK GENMASK(28,
>>>> 26)
>>>> + #define U2P_R1_COMP_DIS_TUNE_MASK GENMASK(31,
>>>> 29)
>>>> +
>>>> +/* bits [31:14] are read-only */
>>>> +#define U2P_R2 0x8
>>>> + #define U2P_R2_DATA_IN_MASK GENMASK(3, 0)
>>>> + #define U2P_R2_DATA_IN_EN_MASK GENMASK(7, 4)
>>>> + #define U2P_R2_ADDR_MASK GENMASK(11, 8)
>>>> + #define U2P_R2_DATA_OUT_SEL BIT(12)
>>>> + #define U2P_R2_CLK BIT(13)
>>>> + #define U2P_R2_DATA_OUT_MASK GENMASK(17,
>>>> 14)
>>>> + #define U2P_R2_ACA_PIN_RANGE_C BIT(18)
>>>> + #define U2P_R2_ACA_PIN_RANGE_B BIT(19)
>>>> + #define U2P_R2_ACA_PIN_RANGE_A BIT(20)
>>>> + #define U2P_R2_ACA_PIN_GND BIT(21)
>>>> + #define U2P_R2_ACA_PIN_FLOAT BIT(22)
>>>> + #define U2P_R2_CHARGE_DETECT BIT(23)
>>>> + #define U2P_R2_DEVICE_SESSION_VALID BIT(24)
>>>> + #define U2P_R2_ADP_PROBE BIT(25)
>>>> + #define U2P_R2_ADP_SENSE BIT(26)
>>>> + #define U2P_R2_SESSION_END BIT(27)
>>>> + #define U2P_R2_VBUS_VALID BIT(28)
>>>> + #define U2P_R2_B_VALID BIT(29)
>>>> + #define U2P_R2_A_VALID BIT(30)
>>>> + #define U2P_R2_ID_DIG BIT(31)
>>>> +
>>>> +#define U2P_R3 0xc
>>>> +
>>>> +#define RESET_COMPLETE_TIME 500
>>>> +
>>>> +struct phy_meson_gxl_usb2_priv {
>>>> + struct regmap *regmap;
>>>> + enum phy_mode mode;
>>>> + int is_enabled;
>>>> +};
>>>> +
>>>> +static const struct regmap_config phy_meson_gxl_usb2_regmap_conf = {
>>>> + .reg_bits = 8,
>>>> + .val_bits = 32,
>>>> + .reg_stride = 4,
>>>> + .max_register = U2P_R3,
>>>> +};
>>>> +
>>>> +static int phy_meson_gxl_usb2_reset(struct phy *phy)
>>>> +{
>>>> + struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
>>>> +
>>>> + if (!priv->is_enabled)
>>>> + return 0;
>>>> +
>>>> + /* reset the PHY and wait until settings are stabilized */
>>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_POWER_ON_RESET,
>>>> + U2P_R0_POWER_ON_RESET);
>>>> + udelay(RESET_COMPLETE_TIME);
>>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_POWER_ON_RESET, 0);
>>>> + udelay(RESET_COMPLETE_TIME);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int phy_meson_gxl_usb2_set_mode(struct phy *phy, enum phy_mode mode)
>>>> +{
>>>> + struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
>>>> +
>>>> + switch (mode) {
>>>> + case PHY_MODE_USB_HOST:
>>>> + case PHY_MODE_USB_OTG:
>>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DM_PULLDOWN,
>>>> + U2P_R0_DM_PULLDOWN);
>>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DP_PULLDOWN,
>>>> + U2P_R0_DP_PULLDOWN);
>>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_ID_PULLUP, 0);
>>>> + break;
>>>> +
>>>> + case PHY_MODE_USB_DEVICE:
>>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DM_PULLDOWN,
>>>> + 0);
>>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DP_PULLDOWN,
>>>> + 0);
>>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_ID_PULLUP,
>>>> + U2P_R0_ID_PULLUP);
>>>> + break;
>>>> +
>>>> + default:
>>>> + return -EINVAL;
>>>> + }
>>>> +
>>>> + phy_meson_gxl_usb2_reset(phy);
>>>> +
>>>> + priv->mode = mode;
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int phy_meson_gxl_usb2_power_off(struct phy *phy)
>>>> +{
>>>> + struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
>>>> +
>>>> + priv->is_enabled = 0;
>>>> +
>>>> + /* power off the PHY by putting it into reset mode */
>>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_POWER_ON_RESET,
>>>> + U2P_R0_POWER_ON_RESET);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int phy_meson_gxl_usb2_power_on(struct phy *phy)
>>>> +{
>>>> + struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
>>>> + int ret;
>>>> +
>>>> + priv->is_enabled = 1;
>>>> +
>>>> + /* power on the PHY by taking it out of reset mode */
>>>> + regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_POWER_ON_RESET, 0);
>>>> +
>>>> + ret = phy_meson_gxl_usb2_set_mode(phy, priv->mode);
>>>> + if (ret) {
>>>> + phy_meson_gxl_usb2_power_off(phy);
>>>> +
>>>> + dev_err(&phy->dev, "Failed to initialize PHY with mode %d\n",
>>>> + priv->mode);
>>>> + return ret;
>>>> + }
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static const struct phy_ops phy_meson_gxl_usb2_ops = {
>>>> + .power_on = phy_meson_gxl_usb2_power_on,
>>>> + .power_off = phy_meson_gxl_usb2_power_off,
>>>> + .set_mode = phy_meson_gxl_usb2_set_mode,
>>>> + .reset = phy_meson_gxl_usb2_reset,
>>>> + .owner = THIS_MODULE,
>>>> +};
>>>> +
>>>> +static int phy_meson_gxl_usb2_probe(struct platform_device *pdev)
>>>> +{
>>>> + struct device *dev = &pdev->dev;
>>>> + struct phy_provider *phy_provider;
>>>> + struct resource *res;
>>>> + struct phy_meson_gxl_usb2_priv *priv;
>>>> + struct phy *phy;
>>>> + void __iomem *base;
>>>> +
>>>> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
>>>> + if (!priv)
>>>> + return -ENOMEM;
>>>> +
>>>> + platform_set_drvdata(pdev, priv);
>>>> +
>>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>>> + base = devm_ioremap_resource(dev, res);
>>>> + if (IS_ERR(base))
>>>> + return PTR_ERR(base);
>>>> +
>>>> + priv->mode = PHY_MODE_USB_HOST;
>>>> +
>>>> + priv->regmap = devm_regmap_init_mmio(dev, base,
>>>> + &phy_meson_gxl_usb2_regmap_conf);
>>>> + if (IS_ERR(priv->regmap))
>>>> + return PTR_ERR(priv->regmap);
>>>> +
>>>> + phy = devm_phy_create(dev, NULL, &phy_meson_gxl_usb2_ops);
>>>> + if (IS_ERR(phy)) {
>>>> + dev_err(dev, "failed to create PHY\n");
>>>> + return PTR_ERR(phy);
>>>> + }
>>>> +
>>>> + phy_set_drvdata(phy, priv);
>>>> +
>>>> + phy_provider = devm_of_phy_provider_register(dev,
>>>> of_phy_simple_xlate);
>>>> +
>>>> + return PTR_ERR_OR_ZERO(phy_provider);
>>>> +}
>>>> +
>>>> +static const struct of_device_id phy_meson_gxl_usb2_of_match[] = {
>>>> + { .compatible = "amlogic,meson-gxl-usb2-phy", },
>>>> + { },
>>>> +};
>>>> +MODULE_DEVICE_TABLE(of, phy_meson_gxl_usb2_of_match);
>>>> +
>>>> +static struct platform_driver phy_meson_gxl_usb2_driver = {
>>>> + .probe = phy_meson_gxl_usb2_probe,
>>>> + .driver = {
>>>> + .name = "phy-meson-gxl-usb2",
>>>> + .of_match_table = phy_meson_gxl_usb2_of_match,
>>>> + },
>>>> +};
>>>> +module_platform_driver(phy_meson_gxl_usb2_driver);
>>>> +
>>>> +MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
>>>> +MODULE_DESCRIPTION("Meson GXL and GXM USB2 PHY driver");
>>>> +MODULE_LICENSE("GPL v2");
>>>> --
>>>> 2.12.2
>>>>
>>> the devicetree documentation already got Rob's ACK. is there anything
>>> that I still need to fix? I would really like to see this getting into
>>> 4.13
>> I don't have any further comments. I'll queue this once -rc1 is tagged. Btw
>> Vivek Gautam has plans to change the directory structure of phy, so you might
>> have to resend this patch once his patch is merged.
>>
>> Vivek, since phy tree is already merged to Linus, can you send your
>> restructuring patch asap based on linus latest?
>
> Sure, I will send the patch soon this week.
Thanks Vivek.
-Kishon
next prev parent reply other threads:[~2017-05-09 5:15 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-03-04 22:22 [PATCH 0/2] Meson GXL USB2 PHY driver Martin Blumenstingl
2017-03-04 22:22 ` [PATCH 1/2] Documentation: dt-bindings: Add documentation for the Meson GXL USB2 PHY Martin Blumenstingl
2017-03-15 19:59 ` Rob Herring
2017-03-04 22:22 ` [PATCH 2/2] phy: meson: add USB2 PHY support for Meson GXL and GXM Martin Blumenstingl
2017-03-06 8:50 ` Hendrik v. Raven
2017-03-09 8:27 ` Kishon Vijay Abraham I
2017-03-09 19:44 ` Martin Blumenstingl
2017-03-10 13:09 ` Kishon Vijay Abraham I
2017-03-18 13:00 ` [PATCH v2 0/2] Meson GXL USB2 PHY driver Martin Blumenstingl
2017-03-18 13:00 ` [PATCH v2 1/2] Documentation: dt-bindings: Add documentation for the Meson GXL USB2 PHY Martin Blumenstingl
2017-03-18 13:00 ` [PATCH v2 2/2] phy: meson: add USB2 PHY support for Meson GXL and GXM Martin Blumenstingl
2017-03-28 21:33 ` Martin Blumenstingl
2017-03-29 10:56 ` Kishon Vijay Abraham I
2017-04-01 9:37 ` Martin Blumenstingl
2017-04-04 13:20 ` Kishon Vijay Abraham I
2017-04-17 19:11 ` [PATCH v3 0/2] Meson GXL USB2 PHY driver Martin Blumenstingl
2017-04-17 19:11 ` [PATCH v3 1/2] Documentation: dt-bindings: Add documentation for the Meson GXL USB2 PHY Martin Blumenstingl
2017-04-17 19:11 ` [PATCH v3 2/2] phy: meson: add USB2 PHY support for Meson GXL and GXM Martin Blumenstingl
2017-05-04 18:08 ` Martin Blumenstingl
2017-05-08 12:21 ` Kishon Vijay Abraham I
2017-05-09 4:47 ` Vivek Gautam
2017-05-09 5:15 ` Kishon Vijay Abraham I [this message]
2017-05-20 13:50 ` [PATCH v4 0/2] Meson GXL USB2 PHY driver Martin Blumenstingl
2017-05-20 13:50 ` [PATCH v4 1/2] Documentation: dt-bindings: Add documentation for the Meson GXL USB2 PHY Martin Blumenstingl
2017-06-06 8:54 ` Kishon Vijay Abraham I
2017-06-06 18:17 ` Martin Blumenstingl
2017-05-20 13:50 ` [PATCH v4 2/2] phy: meson: add USB2 PHY support for Meson GXL and GXM Martin Blumenstingl
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20f7a149-12b1-bf00-fe33-0adad31c436e@ti.com \
--to=kishon@ti.com \
--cc=linus-amlogic@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®