From: Stefan Agner <stefan@agner.ch>
To: khilman@baylibre.com
Cc: devicetree@vger.kernel.org, narmstrong@baylibre.com,
martin.blumenstingl@googlemail.com, christianshewitt@gmail.com,
linux-kernel@vger.kernel.org, robh+dt@kernel.org,
jian.hu@amlogic.com, Stefan Agner <stefan@agner.ch>,
linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org, jbrunet@baylibre.com
Subject: [PATCH v3 2/5] arm64: dts: meson: fix PHY deassert timing requirements
Date: Mon, 7 Dec 2020 18:58:00 +0100 [thread overview]
Message-ID: <4a322c198b86e4c8b3dda015560a683babea4d63.1607363522.git.stefan@agner.ch> (raw)
In-Reply-To: <df3f5c4fc6e43c55429fd3662a636036a21eed49.1607363522.git.stefan@agner.ch>
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. This fixes an issue seen on ODROID-C2 where the Ethernet
link doesn't come up when using ip link set down/up:
[ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down
[ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36)
[ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma
[ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed
Fixes: f29cabf240ed ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
---
arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts | 2 +-
9 files changed, 9 insertions(+), 9 deletions(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
index 7be3e354093b..de27beafe9db 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
@@ -165,7 +165,7 @@ eth_phy0: ethernet-phy@0 {
reg = <0>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index 70fcfb7b0683..50de1d01e565 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -200,7 +200,7 @@ eth_phy0: ethernet-phy@0 {
reg = <0>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
index 222ee8069cfa..9b0b81f191f1 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
@@ -126,7 +126,7 @@ eth_phy0: ethernet-phy@0 {
reg = <0>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
index ad812854a107..a350fee1264d 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
@@ -147,7 +147,7 @@ eth_phy0: ethernet-phy@0 {
reg = <0>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
index b08c4537f260..b2ab05c22090 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
@@ -82,7 +82,7 @@ external_phy: ethernet-phy@0 {
/* External PHY reset is shared with internal PHY Led signal */
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts
index bff8ec2c1c70..e38d9e50caa7 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts
@@ -194,7 +194,7 @@ external_phy: ethernet-phy@0 {
reg = <0>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
index 83eca3af44ce..dfa7a37a1281 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
@@ -112,7 +112,7 @@ external_phy: ethernet-phy@0 {
max-speed = <1000>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
};
};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts
index ea45ae0c71b7..8edbfe040805 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts
@@ -64,7 +64,7 @@ external_phy: ethernet-phy@0 {
/* External PHY reset is shared with internal PHY Led signal */
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts
index c89c9f846fb1..dde7cfe12cff 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts
@@ -114,7 +114,7 @@ external_phy: ethernet-phy@0 {
max-speed = <1000>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
};
};
--
2.29.2
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
next prev parent reply other threads:[~2020-12-07 17:58 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-12-07 17:57 [PATCH v3 1/5] arm64: dts: meson: g12b: odroid-n2: " Stefan Agner
2020-12-07 17:58 ` Stefan Agner [this message]
2020-12-07 17:58 ` [PATCH v3 3/5] ARM: dts: meson: " Stefan Agner
2020-12-07 17:58 ` [PATCH v3 4/5] arm64: dts: meson: g12a: x96-max: " Stefan Agner
2020-12-07 17:58 ` [PATCH v3 5/5] arm64: dts: meson: g12b: w400: " Stefan Agner
2020-12-07 19:15 ` [PATCH v3 1/5] arm64: dts: meson: g12b: odroid-n2: " Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4a322c198b86e4c8b3dda015560a683babea4d63.1607363522.git.stefan@agner.ch \
--to=stefan@agner.ch \
--cc=christianshewitt@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=jbrunet@baylibre.com \
--cc=jian.hu@amlogic.com \
--cc=khilman@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=martin.blumenstingl@googlemail.com \
--cc=narmstrong@baylibre.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®