Re: [PATCH 2/8] drm/meson: add HDMI div40 TMDS mode

From: Andrzej Hajda <a.hajda@samsung.com>
To: Neil Armstrong <narmstrong@baylibre.com>,
	Laurent.pinchart@ideasonboard.com
Cc: linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org,
	dri-devel@lists.freedesktop.org
Subject: Re: [PATCH 2/8] drm/meson: add HDMI div40 TMDS mode
Date: Fri, 18 Jan 2019 10:13:28 +0100	[thread overview]
Message-ID: <5103b2e8-2f73-da18-a043-fa45d6e2c139@samsung.com> (raw)
In-Reply-To: <20190115123315.11069-3-narmstrong@baylibre.com>

On 15.01.2019 13:33, Neil Armstrong wrote:
> Add support for TMDS Clock > 3.4GHz for HDMI2.0 display modes.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
>  drivers/gpu/drm/meson/meson_dw_hdmi.c | 23 +++++++++++++++++++----
>  1 file changed, 19 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/gpu/drm/meson/meson_dw_hdmi.c b/drivers/gpu/drm/meson/meson_dw_hdmi.c
> index 807111ebfdd9..3d8decb77019 100644
> --- a/drivers/gpu/drm/meson/meson_dw_hdmi.c
> +++ b/drivers/gpu/drm/meson/meson_dw_hdmi.c
> @@ -365,7 +365,8 @@ static int dw_hdmi_phy_init(struct dw_hdmi *hdmi, void *data,
>  	unsigned int wr_clk =
>  		readl_relaxed(priv->io_base + _REG(VPU_HDMI_SETTING));
>  
> -	DRM_DEBUG_DRIVER("%d:\"%s\"\n", mode->base.id, mode->name);
> +	DRM_DEBUG_DRIVER("%d:\"%s\" div%d\n", mode->base.id, mode->name,
> +			 mode->clock > 340000 ? 40 : 10);
>  
>  	/* Enable clocks */
>  	regmap_update_bits(priv->hhi, HHI_HDMI_CLK_CNTL, 0xffff, 0x100);
> @@ -385,9 +386,17 @@ static int dw_hdmi_phy_init(struct dw_hdmi *hdmi, void *data,
>  	/* Enable normal output to PHY */
>  	dw_hdmi_top_write(dw_hdmi, HDMITX_TOP_BIST_CNTL, BIT(12));
>  
> -	/* TMDS pattern setup (TOFIX pattern for 4k2k scrambling) */
> -	dw_hdmi_top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_01, 0x001f001f);
> -	dw_hdmi_top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_23, 0x001f001f);
> +	/* TMDS pattern setup (TOFIX Handle the YUV420 case) */
> +	if (mode->clock > 340000) {
> +		dw_hdmi_top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_01, 0);
> +		dw_hdmi_top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_23,
> +				  0x03ff03ff);
> +	} else {
> +		dw_hdmi_top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_01,
> +				  0x001f001f);
> +		dw_hdmi_top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_23,
> +				  0x001f001f);
> +	}

    val = mode->clock > 340000 ? 0x03ff03ff : 0x001f001f;
    dw_hdmi_top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_01, val);

    dw_hdmi_top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_23, val);

The best would be to replace these magic values with descriptive macros.

Regards

Andrzej

>  
>  	/* Load TMDS pattern */
>  	dw_hdmi_top_write(dw_hdmi, HDMITX_TOP_TMDS_CLK_PTTN_CNTL, 0x1);
> @@ -413,6 +422,8 @@ static int dw_hdmi_phy_init(struct dw_hdmi *hdmi, void *data,
>  	/* Disable clock, fifo, fifo_wr */
>  	regmap_update_bits(priv->hhi, HHI_HDMI_PHY_CNTL1, 0xf, 0);
>  
> +	dw_hdmi_set_high_tmds_clock_ratio(hdmi);
> +
>  	msleep(100);
>  
>  	/* Reset PHY 3 times in a row */
> @@ -562,6 +573,10 @@ dw_hdmi_mode_valid(struct drm_connector *connector,
>  		mode->vdisplay, mode->vsync_start,
>  		mode->vsync_end, mode->vtotal, mode->type, mode->flags);
>  
> +	/* If sink max TMDS clock, we reject the mode */
> +	if (mode->clock > connector->display_info.max_tmds_clock)
> +		return MODE_BAD;
> +
>  	/* Check against non-VIC supported modes */
>  	if (!vic) {
>  		status = meson_venc_hdmi_supported_mode(mode);

_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic