Re: [PATCH v2] ACPI: DPTF: Add new PCH FIVR methods

[Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>]

On Tue, 2021-05-18 at 11:36 +0200, Rafael J. Wysocki wrote:
> On Tue, May 18, 2021 at 5:42 AM Srinivas Pandruvada
> <srinivas.pandruvada@linux.intel.com> wrote:
> > 
> > Some additional information is required for updating PCH FIVR
> > values
> > upon WiFi channel changes.
> > 
> > New attributes added to the existing sysfs:
> > fivr_switching_freq_mhz : Get the FIVR switching control frequency
> >                           using ACPI method GFCS. Refer to the
> >                           documentation for the equation.
> > fivr_switching_fault_status: Read the FIVR switching frequency
> > control
> >                         fault status. Uses ACPI method GFFS
> > 
> > ssc_clock_info : Presents SSC (spread spectrum clock) information
> > for EMI
> > (Electro magnetic interference) control. Use ACPI method GEMI.
> > Refer
> > to the description of GEMI method below.
> > 
> > GFFS
> > This ACPI method is used to read the FIVR switching frequency
> > control
> > fault status.
> > Bits    Description
> > [0:0]   Fault status when set to 1
> > [31:1]  Reserved
> > 
> > GFCS
> > This ACPI method is used to read the FIVR switching control
> > frequency.
> > Bits    Description
> > [11:0]  Actual Frequency = value * XTAL_FREQ / 128
> > [31:12] Reserved
> > 
> > GEMI
> > This ACPI method is used to read the programmed register value for
> > EMI
> > (Electro magnetic interference) control.
> > 
> > Bits    Description
> > [7:0]   Sets clock spectrum spread percentage:
> >         0x00=0.2% , 0x3F=10%
> >         1 LSB = 0.1% increase in spread (for
> >         settings 0x01 thru 0x1C)
> >         1 LSB = 0.2% increase in spread (for
> >         settings 0x1E thru 0x3F)
> > [8]     When set to 1, enables spread
> >         spectrum clock
> > [9]     0: Triangle mode. FFC frequency
> >         walks around the Fcenter in a linear
> >         fashion
> >         1: Random walk mode. FFC frequency
> >         changes randomly within the SSC
> >         (Spread spectrum clock) range
> > [10]    0: No white noise. 1: Add white noise
> >         to spread waveform
> > [11]    When 1, future writes are ignored.
> > 
> > Signed-off-by: Srinivas Pandruvada <  
> > srinivas.pandruvada@linux.intel.com>
> > ---
> > v2
> >         Update documentation for fivr_switching_freq_mhz
> > 
> >  Documentation/ABI/testing/sysfs-platform-dptf | 42
> > +++++++++++++++++++
> >  drivers/acpi/dptf/dptf_pch_fivr.c             |  9 ++++
> >  2 files changed, 51 insertions(+)
> > 
> > diff --git a/Documentation/ABI/testing/sysfs-platform-dptf
> > b/Documentation/ABI/testing/sysfs-platform-dptf
> > index 141834342a4d..fe62f024eb93 100644
> > --- a/Documentation/ABI/testing/sysfs-platform-dptf
> > +++ b/Documentation/ABI/testing/sysfs-platform-dptf
> > @@ -111,3 +111,45 @@ Contact:   linux-acpi@vger.kernel.org
> >  Description:
> >                 (RW) The PCH FIVR (Fully Integrated Voltage
> > Regulator) switching frequency in MHz,
> >                 when FIVR clock is 38.4MHz.
> > +
> > +What:         
> > /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fiv
> > r_switching_freq_mhz
> > +Date:          June, 2021
> > +KernelVersion: v5.14
> > +Contact:       linux-acpi@vger.kernel.org
> > +Description:
> > +               (RO) Get the FIVR switching control frequency in
> > MHz after applying equation
> > +               "fivr_switching_freq_mhz * XTAL_FREQ / 128". Here
> > XTAL_FREQ is Crystal Oscillator frequency
> > +               in MHz, which is product specific.
> 
> IMO it would be sufficient to say the following here:
> 
> +               (RO) PCH FIVR switching control frequency in the
> units
> of XTAL_FREQ / 128,
> +               where XTAL_FREQ is the Crystal Oscillator frequency
> (product specific).
> 
> This means that it needs to be multiplied by XTAL_FREQ / 128 to get
> the frequency in the whatever units XTAL_FREQ is expressed.
> 
Looks good.

> I can make this change when applying the patch.

> 
Thanks,
Srinivas


> > +What:         
> > /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fiv
> > r_switching_fault_status
> > +Date:          June, 2021
> > +KernelVersion: v5.14
> > +Contact:       linux-acpi@vger.kernel.org
> > +Description:
> > +               (RO) Read the FIVR switching frequency control
> > fault status.
> > +
> > +What:         
> > /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/ssc
> > _clock_info
> > +Date:          June, 2021
> > +KernelVersion: v5.14
> > +Contact:       linux-acpi@vger.kernel.org
> > +Description:
> > +               (RO) Presents SSC (spread spectrum clock)
> > information for EMI
> > +               (Electro magnetic interference) control. This is a
> > bit mask.
> > +               Bits    Description
> > +               [7:0]   Sets clock spectrum spread percentage:
> > +                       0x00=0.2% , 0x3F=10%
> > +                       1 LSB = 0.1% increase in spread (for
> > +                       settings 0x01 thru 0x1C)
> > +                       1 LSB = 0.2% increase in spread (for
> > +                       settings 0x1E thru 0x3F)
> > +               [8]     When set to 1, enables spread
> > +                       spectrum clock
> > +               [9]     0: Triangle mode. FFC frequency
> > +                       walks around the Fcenter in a linear
> > +                       fashion
> > +                       1: Random walk mode. FFC frequency
> > +                       changes randomly within the SSC
> > +                       (Spread spectrum clock) range
> > +               [10]    0: No white noise. 1: Add white noise
> > +                       to spread waveform
> > +               [11]    When 1, future writes are ignored.
> > diff --git a/drivers/acpi/dptf/dptf_pch_fivr.c
> > b/drivers/acpi/dptf/dptf_pch_fivr.c
> > index 5fca18296bf6..22c4ae0401ef 100644
> > --- a/drivers/acpi/dptf/dptf_pch_fivr.c
> > +++ b/drivers/acpi/dptf/dptf_pch_fivr.c
> > @@ -55,15 +55,24 @@ static ssize_t name##_store(struct device
> > *dev,\
> > 
> >  PCH_FIVR_SHOW(freq_mhz_low_clock, GFC0)
> >  PCH_FIVR_SHOW(freq_mhz_high_clock, GFC1)
> > +PCH_FIVR_SHOW(ssc_clock_info, GEMI)
> > +PCH_FIVR_SHOW(fivr_switching_freq_mhz, GFCS)
> > +PCH_FIVR_SHOW(fivr_switching_fault_status, GFFS)
> >  PCH_FIVR_STORE(freq_mhz_low_clock, RFC0)
> >  PCH_FIVR_STORE(freq_mhz_high_clock, RFC1)
> > 
> >  static DEVICE_ATTR_RW(freq_mhz_low_clock);
> >  static DEVICE_ATTR_RW(freq_mhz_high_clock);
> > +static DEVICE_ATTR_RO(ssc_clock_info);
> > +static DEVICE_ATTR_RO(fivr_switching_freq_mhz);
> > +static DEVICE_ATTR_RO(fivr_switching_fault_status);
> > 
> >  static struct attribute *fivr_attrs[] = {
> >         &dev_attr_freq_mhz_low_clock.attr,
> >         &dev_attr_freq_mhz_high_clock.attr,
> > +       &dev_attr_ssc_clock_info.attr,
> > +       &dev_attr_fivr_switching_freq_mhz.attr,
> > +       &dev_attr_fivr_switching_fault_status.attr,
> >         NULL
> >  };
> > 
> > --
> > 2.27.0
> >