From: Benjamin Hahn <B.Hahn@phytec.de>
To: Frank Li <Frank.li@oss.nxp.com>
Cc: Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Shawn Guo <shawnguo@kernel.org>, Frank Li <Frank.Li@nxp.com>,
Sascha Hauer <s.hauer@pengutronix.de>,
Pengutronix Kernel Team <kernel@pengutronix.de>,
Fabio Estevam <festevam@gmail.com>,
Yannic Moog <y.moog@phytec.de>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
imx@lists.linux.dev, linux-arm-kernel@lists.infradead.org,
upstream@lists.phytec.de
Subject: Re: [PATCH v2 3/5] arm64: dts: imx95-phyflex-libra-rdk: Add overlays
Date: Tue, 17 Nov 2026 10:32:25 +0100 [thread overview]
Message-ID: <06904f2c-379b-412a-a842-04d7898c56d4@phytec.de> (raw)
In-Reply-To: <avc7o0T0-tSW_c0H@SMW015318>
Am 13.11.26 um 17:32 schrieb Frank Li:
> On Fri, Nov 13, 2026 at 05:00:05PM +0100, Benjamin Hahn wrote:
>
> subject Add overlay for som temperature sensors and ...
>
>> Add overlays for SoM temperature sensors and M.2 Key-E WIFI/BT cards
>> that need the nxp,88w8987-bt compatible in devicetree (tested on
>> IW611/IW612).
>>
>> Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
>> ---
>> arch/arm64/boot/dts/freescale/Makefile | 9 ++++++++
>> .../imx95-phyflex-fpsc-g-som-temperature.dtso | 23 +++++++++++++++++++++
>> .../imx95-phyflex-libra-rdk-bluetooth-88w8987.dtso | 24 ++++++++++++++++++++++
> which is independ, suggest use two patches to do that.
Will do
>
>> 3 files changed, 56 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
>> index 4eb7508193e7..17b357f4886a 100644
>> --- a/arch/arm64/boot/dts/freescale/Makefile
>> +++ b/arch/arm64/boot/dts/freescale/Makefile
>> @@ -739,7 +739,16 @@ imx95-19x19-evk-pcie1-ep-dtbs += imx95-19x19-evk.dtb imx-pcie1-ep.dtbo
>> dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-evk-pcie0-ep.dtb imx95-19x19-evk-pcie1-ep.dtb
>> dtb-$(CONFIG_ARCH_MXC) += imx95-libra-rdk-fpsc.dtb
>>
>> +imx95-phyflex-fpsc-g-som-temperature-dtbs := \
>> + imx95-phyflex-libra-rdk.dtb \
>> + imx95-phyflex-fpsc-g-som-temperature.dtbo
>> +imx95-phyflex-libra-rdk-bluetooth-88w8987-dtbs := \
>> + imx95-phyflex-libra-rdk.dtb \
>> + imx95-phyflex-libra-rdk-bluetooth-88w8987.dtbo
>> +
>> dtb-$(CONFIG_ARCH_MXC) += imx95-phyflex-libra-rdk.dtb
>> +dtb-$(CONFIG_ARCH_MXC) += imx95-phyflex-fpsc-g-som-temperature.dtb
>> +dtb-$(CONFIG_ARCH_MXC) += imx95-phyflex-libra-rdk-bluetooth-88w8987.dtb
>>
>> dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-verdin-evk.dtb
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx95-phyflex-fpsc-g-som-temperature.dtso b/arch/arm64/boot/dts/freescale/imx95-phyflex-fpsc-g-som-temperature.dtso
>> new file mode 100644
>> index 000000000000..84afe1ff9f06
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/freescale/imx95-phyflex-fpsc-g-som-temperature.dtso
>> @@ -0,0 +1,23 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Copyright (C) 2026 PHYTEC Messtechnik GmbH
>> + */
>> +
>> +/dts-v1/;
>> +/plugin/;
>> +
>> +&dram_sense {
>> + status = "okay";
>> +};
>> +
>> +&emmc_sense {
>> + status = "okay";
>> +};
>> +
>> +ðphy_sense {
>> + status = "okay";
>> +};
>> +
>> +&pmic_sense {
>> + status = "okay";
>> +};
>> diff --git a/arch/arm64/boot/dts/freescale/imx95-phyflex-libra-rdk-bluetooth-88w8987.dtso b/arch/arm64/boot/dts/freescale/imx95-phyflex-libra-rdk-bluetooth-88w8987.dtso
>> new file mode 100644
>> index 000000000000..1601e04b3940
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/freescale/imx95-phyflex-libra-rdk-bluetooth-88w8987.dtso
>> @@ -0,0 +1,24 @@
>> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
>> +/*
>> + * Copyright (C) 2026 PHYTEC Messtechnik GmbH
>> + */
>> +/dts-v1/;
>> +/plugin/;
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +
>> +&lpuart8 {
>> + bluetooth {
> Can you add label for bluetooth at boards file, so this overlay can
> reuse for other 88w8987-bt module.
This would be technically possible, but I don't think it is the cleanest
solution.
1. adding an empty bluetooth node into the base dts leads to DTBS_CHECK
errors:
arch/arm64/boot/dts/freescale/imx95-phyflex-libra-rdk.dtb:
serial@426a0000 (fsl,imx95-lpuart): bluetooth: 'compatible' is a
required property
from schema $id:
http://devicetree.org/schemas/serial/fsl-lpuart.yaml
arch/arm64/boot/dts/freescale/imx95-phyflex-libra-rdk.dtb:
serial@426a0000 (fsl,imx95-lpuart): Unevaluated properties are not
allowed ('bluetooth', 'uart-has-rtscts' were unexpected)
from schema $id:
http://devicetree.org/schemas/serial/fsl-lpuart.yaml
arch/arm64/boot/dts/freescale/imx95-phyflex-libra-rdk.dtb:
serial@426a0000 (fsl,imx95-lpuart): bluetooth: 'compatible' is a
required property
from schema $id: http://devicetree.org/schemas/serial/serial.yaml
2. I also think this is a bit missleading, as this UART is not used fix
for bluetooth on M.2 Key-E, but its default is RS232/RS485. It can be
switched to Key-E by the Multiplexer controlled by UART1_BT_RS_SEL GPIO.
The (default) state of this GPIO also needs to be switched when
enabling this overlay. So this leads to the overlay not beeing generic
anyway.
>
>> + compatible = "nxp,88w8987-bt";
>> + fw-init-baudrate = <115200>;
>> + };
>> +};
>> +
>> +&gpio_expander1 {
>> + uart1_bt_rs_sel: bt-rs-hog {
>> + gpios = <14 GPIO_ACTIVE_HIGH>;
>> + gpio-hog;
> Look like it is pinmux ref gpio-mux
>
> https://lore.kernel.org/imx/20261023-dxl_lcdif-v4-5-4ae8395a4b23@nxp.com/
Looks like a good solution, will do.
Benjamin
>
> Frank
>> + line-name = "UART1_BT_RS_SEL";
>> + output-high;
>> + };
>> +};
>>
>> --
>> 2.53.0
>>
>>
next prev parent reply other threads:[~2026-11-17 9:32 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-13 16:00 [PATCH v2 0/5] arm64: dts: update imx95 Libra for the newest hardware version Benjamin Hahn
2026-11-13 16:00 ` [PATCH v2 1/5] dt-bindings: arm: fsl: Add phyFLEX-i.MX 95 Libra RDK Benjamin Hahn
2026-11-13 16:48 ` Conor Dooley
2026-11-13 16:00 ` [PATCH v2 2/5] arm64: dts: imx95-phyflex-libra-rdk: " Benjamin Hahn
2026-11-13 16:00 ` [PATCH v2 3/5] arm64: dts: imx95-phyflex-libra-rdk: Add overlays Benjamin Hahn
2026-11-13 16:32 ` Frank Li
2026-11-17 9:32 ` Benjamin Hahn [this message]
2026-11-13 16:00 ` [PATCH v2 4/5] arm64: dts: imx95-libra-rdk-fpsc: remove devicetree for old Libra Benjamin Hahn
2026-11-13 16:00 ` [PATCH v2 5/5] dt-bindings: arm: fsl: remove outdated PHYTEC i.MX95 FPSC Benjamin Hahn
2026-11-13 16:48 ` Conor Dooley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=06904f2c-379b-412a-a842-04d7898c56d4@phytec.de \
--to=b.hahn@phytec.de \
--cc=Frank.Li@nxp.com \
--cc=Frank.li@oss.nxp.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=imx@lists.linux.dev \
--cc=kernel@pengutronix.de \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
--cc=upstream@lists.phytec.de \
--cc=y.moog@phytec.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®