mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Zhou Yanjie <zhouyanjie@wanyeetech.com>
To: Paul Cercueil <paul@crapouillou.net>,
	Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
	robh+dt@kernel.org, tglx@linutronix.de,
	dongsheng.qiu@ingenic.com, aric.pzqi@ingenic.com,
	rick.tyliu@ingenic.com, yanfei.li@ingenic.com,
	sernia.zhou@foxmail.com, zhenwenjin@gmail.com
Subject: Re: [PATCH v6 2/2] clocksource: Ingenic: Add support for the Ingenic X1000 OST.
Date: Sat, 18 Jul 2020 21:42:26 +0800	[thread overview]
Message-ID: <096c8788-3c50-3eae-1c8e-c0c7487b00af@wanyeetech.com> (raw)
In-Reply-To: <512ODQ.64YN0BEY1JJG@crapouillou.net>

Hello Paul and Daniel,

在 2020/7/18 下午9:12, Paul Cercueil 写道:
> Hi Daniel,
>
> Le ven. 17 juil. 2020 à 10:02, Daniel Lezcano 
> <daniel.lezcano@linaro.org> a écrit :
>> On 17/07/2020 08:13, Zhou Yanjie wrote:
>>>  Hi Daniel,
>>>
>>>  在 2020/7/17 下午12:20, Daniel Lezcano 写道:
>>>>  On 10/07/2020 19:02, 周琰杰 (Zhou Yanjie) wrote:
>>>>>  X1000 and SoCs after X1000 (such as X1500 and X1830) had a separate
>>>>>  OST, it no longer belongs to TCU. This driver will register both a
>>>>>  clocksource and a sched_clock to the system.
>>>>>
>>>>>  Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
>>>>>  Co-developed-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com>
>>>>>  Signed-off-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com>
>>>>>  Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
>>>>>  Reviewed-by: Paul Cercueil <paul@crapouillou.net>
>>>>>  ---
>>>>>
>>>>>  Notes:
>>>>>       v1->v2:
>>>>>       Fix compile warnings.
>>>>>       Reported-by: kernel test robot <lkp@intel.com>
>>>>>            v2->v3:
>>>>>       No change.
>>>>>            v3->v4:
>>>>>       1.Rename "ost" to "sysost"
>>>>>       1.Remove unrelated changes.
>>>>>       2.Remove ost_clock_parent enum.
>>>>>       3.Remove ost->percpu_timer_channel/ost->global_timer_channel.
>>>>>       4.Set up independent .recalc_rate/.set_rate for percpu/global
>>>>>  timer.
>>>>>       5.No longer call functions in variable declarations.
>>>>>            v4->v5:
>>>>>       Use "of_io_request_and_map()" instead "of_iomap()".
>>>>>       Suggested-by: Paul Cercueil <paul@crapouillou.net>
>>>>>            v5->v6:
>>>>>       No change.
>>>>>
>>>>>    drivers/clocksource/Kconfig          |  11 +
>>>>>    drivers/clocksource/Makefile         |   1 +
>>>>>    drivers/clocksource/ingenic-sysost.c | 539
>>>>>  +++++++++++++++++++++++++++++++++++
>>>>>    3 files changed, 551 insertions(+)
>>>>>    create mode 100644 drivers/clocksource/ingenic-sysost.c
>>>>>
>>>>>  diff --git a/drivers/clocksource/Kconfig 
>>>>> b/drivers/clocksource/Kconfig
>>>>>  index 91418381fcd4..1bca8b8fb30f 100644
>>>>>  --- a/drivers/clocksource/Kconfig
>>>>>  +++ b/drivers/clocksource/Kconfig
>>>>>  @@ -696,6 +696,17 @@ config INGENIC_TIMER
>>>>>        help
>>>>>          Support for the timer/counter unit of the Ingenic JZ SoCs.
>>>>>    +config INGENIC_SYSOST
>>>>>  +    bool "Clocksource/timer using the SYSOST in Ingenic X SoCs"
>>>>  We usually use silent options and let the platform's Kconfig 
>>>> enable it.
>>>>  We show up the option only when COMPILE_TEST is enabled.
>>>>
>>>>  Is there a reason to do it differently?
>>>
>>>
>>>  Do you mean
>>>
>>>  bool "Clocksource/timer using the SYSOST in Ingenic X SoCs"
>>>
>>>  or
>>>
>>>  default MACH_INGENIC ?
>>
>> Both, no default here.
>>
>> eg.
>>
>> bool "Clocksource/timer using the SYSOST in Ingenic X SoCs" if 
>> COMPILE_TEST
>>
>> and
>>
>> in arch/mips/Kconfig in the config MACH_INGENIC section :
>>
>> ...
>> select INGENIC_SYSOST
>> ...
>
> Disagreed. That's not how we do things on MIPS. Selecting MACH_INGENIC 
> means "this kernel will support Ingenic SoCs", but not that it will 
> only support these. Hence the depends on MIPS / default MACH_INGENIC.
>
> As for the select INGENIC_SYSOST, this driver only applies to a few 
> SoCs, I certainly don't want it to be force-enabled. I don't even wait 
> it to be force-enabled on X1000, since it is optional there too.
>
> Cheers,
> -Paul


If we still need to keep the "default MACH_INGENIC", then Daniel can 
directly apply the v6 version.

If we need to use the silent options, maybe we can enable them 
separately according to 
MACH_JZ4740/MACH_JZ4770/MACH_JZ4780/MACH_X1000/MACH_X1830.

In fact, I think X1000 and X1830 need to enable this driver in most 
cases, because the current test has found that use TCU to provide 
clocksource and clockevent will cause data loss/error when transmitting 
data through spi or ethernet. And these errors no longer appear after 
using OST.

Thanks and best regards!


>
>>
>>>  This driver has some origins from "INGENIC_TIMER" driver and
>>>  "INGENIC_OST" driver.
>>>  Early Ingenic processors used TCU (timer/counter unit, has 6 or 8
>>>  generic timer channels) to provide clocksource and clockevent (both 
>>> with
>>>  only 16bit precision). This part of the processor can only use
>>>  "INGENIC_TIMER" driver.
>>>
>>>  Later processors provide an independent 32bit or 64bit timer channel
>>>  (still under TCU, known as ost channel, this channel can not generate
>>>  interrupt) to provid higher precision clocksource. The "INGENIC_OST"
>>>  driver is for this channel. These processors can use "INGENIC_TIMER"
>>>  driver, but using "INGENIC_OST" driver to provide higher precision
>>>  clocksource would be a better choice (clockevent still needs to be
>>>  provided by generic timer channel of TCU, and still 16bit precision).
>>>
>>>  And the recent processors provide a SYSOST components, it is 
>>> independent
>>>  from TCU, including a 64bit timer channel for clocksource and a 32bit
>>>  timer channel for clockevent. Although these processors can also use
>>>  "INGENIC_TIMER" driver, but the better choice is completely 
>>> independent
>>>  use of "INGENIC_SYSOST" driver to provide higher precision clocksource
>>>  and clockevent.
>>
>> Ok, the rating should do the job then.
>>
>> Thanks for the explanation.
>>
>>>  You may have already noticed that this independent SYSOST component is
>>>  like an upgraded and streamlined TCU, which only retains one generic
>>>  timer channel that can generate interrupts, upgrade it from 16bit to
>>>  32bit, and then retain the 64bit ost channel. so the driver code and
>>>  Kconfig code of this patch is largely referenced
>>>  "INGENIC_TIMER" driver and "INGENIC_OST" driver.
>>>
>>>  Thanks and best regards!
>>>
>>>>>  +    default MACH_INGENIC
>>>>>  +    depends on MIPS || COMPILE_TEST
>>>>>  +    depends on COMMON_CLK
>>>>>  +    select MFD_SYSCON
>>>>>  +    select TIMER_OF
>>>>>  +    select IRQ_DOMAIN
>>>>>  +    help
>>>>>  +      Support for the SYSOST of the Ingenic X Series SoCs.
>>>>>  +
>>>>  [ ... ]
>>>>
>>>>
>>
>>
>> -- 
>> <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
>>
>> Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
>> <http://twitter.com/#!/linaroorg> Twitter |
>> <http://www.linaro.org/linaro-blog/> Blog
>

  reply	other threads:[~2020-07-18 13:42 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-07-10 17:02 [PATCH v6 0/2] Add support for the OST in Ingenic X1000 周琰杰 (Zhou Yanjie)
2020-07-10 17:02 ` [PATCH v6 1/2] dt-bindings: timer: Add Ingenic X1000 OST bindings 周琰杰 (Zhou Yanjie)
2020-07-13 15:52   ` Rob Herring
2020-07-10 17:02 ` [PATCH v6 2/2] clocksource: Ingenic: Add support for the Ingenic X1000 OST 周琰杰 (Zhou Yanjie)
2020-07-17  4:20   ` Daniel Lezcano
2020-07-17  6:13     ` Zhou Yanjie
2020-07-17  8:02       ` Daniel Lezcano
2020-07-17 14:40         ` Zhou Yanjie
2020-07-18 13:12         ` Paul Cercueil
2020-07-18 13:42           ` Zhou Yanjie [this message]
2020-07-18 15:44             ` Paul Cercueil
2020-07-18 15:55               ` Zhou Yanjie
2020-07-18 16:11                 ` Paul Cercueil
2020-07-18 16:18                   ` Zhou Yanjie

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=096c8788-3c50-3eae-1c8e-c0c7487b00af@wanyeetech.com \
    --to=zhouyanjie@wanyeetech.com \
    --cc=aric.pzqi@ingenic.com \
    --cc=daniel.lezcano@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dongsheng.qiu@ingenic.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=paul@crapouillou.net \
    --cc=rick.tyliu@ingenic.com \
    --cc=robh+dt@kernel.org \
    --cc=sernia.zhou@foxmail.com \
    --cc=tglx@linutronix.de \
    --cc=yanfei.li@ingenic.com \
    --cc=zhenwenjin@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®