Linux version 2.6.9-rc2-mm1 (root@teapot) (gcc version 3.3.4 (Debian 1:3.3.4-11)) #1 Sun Sep 19 21:31:51 CEST 2004
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
 BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
 BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65520
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 61424 pages, LIFO batch:14
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 NEC                                   ) @ 0x000fb550
ACPI: RSDT (v001    NEC ND000020 0x00000001 MSFT 0x00000097) @ 0x0fff0000
ACPI: FADT (v001    NEC ND000020 0x00000001 MSFT 0x00000097) @ 0x0fff0030
ACPI: BOOT (v001    NEC ND000020 0x00000001 MSFT 0x00000097) @ 0x0fff00b0
ACPI: DSDT (v001    NEC ND000020 0x00000001 MSFT 0x0100000a) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
Built 1 zonelists
Initializing CPU#0
Kernel command line: root=/dev/hda1 ro 
CPU 0 irqstacks, hard=c030d000 soft=c030c000
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 697.084 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256812k/262080k available (1420k kernel code, 4700k reserved, 550k data, 100k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1380.35 BogoMIPS (lpj=690176)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000
CPU: After vendor identify, caps:  0383f9ff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps:        0383f9ff 00000000 00000000 00000040
CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: IRQ9 SCI: Level Trigger.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdb81, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
requesting new irq thread for IRQ9...
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [NRTH] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.NRTH._PRT]
ACPI: Embedded Controller [EC0] (gpe 9)
ACPI: Power Resource [PUSB] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 10) *0
ACPI: PCI Interrupt Link [LNKB] (IRQs 5) *0
ACPI: PCI Interrupt Link [LNKC] (IRQs 5 7 10) *0
ACPI: PCI Interrupt Link [LNKD] (IRQs 9) *0
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically.  If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device().  As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior.  If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
Simple Boot Flag at 0x7e set to 0x1
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
i8042: ACPI  [P2KI] at I/O 0x0, 0x0, irq 1
i8042: ACPI  [P2MI] at irq 12
i8042.c: Can't read CTR while initializing i8042.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: HITACHI_DK23BA-20, ATA DISK drive
requesting new irq thread for IRQ14...
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: MATSHITADVD-ROM SR-8185, ATAPI CD/DVD-ROM drive
requesting new irq thread for IRQ15...
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
IRQ#14 thread started up.
hda: 39070080 sectors (20003 MB) w/2048KiB Cache, CHS=38760/16/63, UDMA(33)
hda: cache flushes not supported
 hda: hda1 hda2 < hda5 >
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
ACPI: (supports S0 S3 S4 S5)
ACPI wakeup devices: 
MDM0 PRB1 LID0 
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 100k freed
NET: Registered protocol family 1
Adding 500936k swap on /dev/hda5.  Priority:-1 extents:1
Generic RTC Driver v1.07
IRQ#15 thread started up.
hdc: ATAPI 24X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Linux agpgart interface v0.100 (c) Dave Jones
Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 10 (level, low) -> IRQ 10
Yenta: CardBus bridge found at 0000:00:0c.0 [1033:80b6]
yenta 0000:00:0c.0: Preassigned resource 3 busy, reconfiguring...
requesting new irq thread for IRQ10...
Yenta: ISA IRQ mask 0x0898, PCI irq 10
Socket status: 30000006
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:0c.1[B] -> GSI 5 (level, low) -> IRQ 5
Yenta: CardBus bridge found at 0000:00:0c.1 [1033:80b6]
yenta 0000:00:0c.1: Preassigned resource 2 busy, reconfiguring...
yenta 0000:00:0c.1: Preassigned resource 3 busy, reconfiguring...
requesting new irq thread for IRQ5...
Yenta: ISA IRQ mask 0x0898, PCI irq 5
Socket status: 30000068
PCI: Enabling device 0000:06:00.0 (0000 -> 0003)
ACPI: PCI interrupt 0000:06:00.0[A] -> GSI 5 (level, low) -> IRQ 5
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:06:00.0: 3Com PCI 3CCFE575CT Tornado CardBus at 0x4400. Vers LK1.1.19
PCI: Setting latency timer of device 0000:06:00.0 to 64
agpgart: Detected an Intel 440BX Chipset.
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 256M @ 0xe0000000
ACPI: PCI interrupt 0000:06:00.0[A] -> GSI 5 (level, low) -> IRQ 5
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9
ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 9 (level, low) -> IRQ 9
uhci_hcd 0000:00:07.2: Intel Corp. 82371AB/EB/MB PIIX4 USB
uhci_hcd 0000:00:07.2: irq 9, io base 0xef80
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using address 2
IRQ#9 thread started up.
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 5 (level, low) -> IRQ 5
eth0: Setting full-duplex based on MII #0 link partner capability of 01e1.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02e3aa0(lo)
IPv6 over IPv4 tunneling driver
IRQ#5 thread started up.
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [AC] (on-line)
ACPI: Processor [CPU0] (supports C1)
ACPI: Power Button (CM) [PRB1]
ACPI: Lid Switch [LID0]
ACPI: Fan [FANC] (on)
ACPI: Thermal Zone [THRM] (64 C)