From: darktim@darktim.dyndns.org
To: linux-kernel@vger.kernel.org
Subject: PROBLEM: Kernel does not boot with Machine Check Exeption
Date: Fri, 15 Mar 2002 12:15:18 +0100 (CET) [thread overview]
Message-ID: <1016190918.3c91d7c69aacd@darktim.dyndns.org> (raw)
Hello.
After I have upgraded mey Kernel from 2.4.19-pre2-ac4 to 2.4.19-pre3
the machine hangs while checking the CPU.
The last message on the screen was:
CPU: L1 I cache: 16k, L1 D cache: 16k
CPU: L2 cache: 512k
Intel machine check architecture supported
After that the system hangs.
After unchecking /Processor type and features/Machine Check Exeption
and recompiling the kernel the machine boots normally.
System is debian_sid on IBM Thinkpad 600
I hope you have enough information to handle this report.
Kindest regards,
Andre Timmermann
Additional info:
/proc/cpuinfo:
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 5
model name : Pentium II (Deschutes)
stepping : 0
cpu MHz : 265.272
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat
pse36 mmx fxsr
bogomips : 529.20
-----
lspci -vvv:
00:00.0 Host bridge: Intel Corp. 440BX/ZX - 82443BX/ZX Host bridge (AGP
disabled) (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+
Latency: 64
Region 0: Memory at <unassigned> (32-bit, prefetchable) [size=256M]
00:02.0 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Subsystem: IBM: Unknown device 0092
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20301000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=03, sec-latency=176
Memory window 0: 10000000-103ff000 (prefetchable)
Memory window 1: 10400000-107ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:02.1 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Subsystem: IBM: Unknown device 0092
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 20300000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=04, subordinate=06, sec-latency=176
Memory window 0: 10800000-10bff000 (prefetchable)
Memory window 1: 10c00000-10fff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:03.0 VGA compatible controller: Neomagic Corporation NM2160 [MagicGraph
128XD] (rev 01) (prog-if 00 [VGA])
Subsystem: IBM MagicGraph 128XD
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at 20000000 (32-bit, non-prefetchable) [size=2M]
Region 2: Memory at 20200000 (32-bit, non-prefetchable) [size=1M]
00:07.0 Bridge: Intel Corp. 82371AB PIIX4 ISA (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corp. 82371AB PIIX4 IDE (rev 01) (prog-if 80
[Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at fcf0 [size=16]
00:07.2 USB Controller: Intel Corp. 82371AB PIIX4 USB (rev 01) (prog-if 00
[UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 48
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 8400 [size=32]
00:07.3 Bridge: Intel Corp. 82371AB PIIX4 ACPI (rev 01)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
-----
ver_linux:
Linux schleppi666 2.4.19-pre3 #3 Fri Mar 15 11:03:48 CET 2002 i686 unknown
Gnu C 2.95.4
Gnu make 3.79.1
util-linux 2.11n
mount 2.11n
modutils 2.4.13
e2fsprogs 1.27
pcmcia-cs 3.1.33
PPP 2.4.1
Linux C Library 2.2.5
Dynamic linker (ldd) 2.2.5
Procps 2.0.7
Net-tools 1.60
Kbd 1.06
Sh-utils 2.0.11
Modules Loaded 3c589_cs nls_iso8859-1 nls_cp437
next reply other threads:[~2002-03-15 11:18 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-03-15 11:15 darktim [this message]
2002-03-15 12:28 ` Dave Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1016190918.3c91d7c69aacd@darktim.dyndns.org \
--to=darktim@darktim.dyndns.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®