Linux version 2.5.11 (it0@it0) (gcc version 2.95.4 20011002 (Debian prerelease)) #4 Mon Apr 29 11:22:23 CEST 2002 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000020000000 (usable) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 512MB LOWMEM available. On node 0 totalpages: 131072 zone(0): 4096 pages. zone(1): 126976 pages. zone(2): 0 pages. Kernel command line: BOOT_IMAGE=custom-2.5.11 root=806 bootfs=ext3 ide0=ata66 hdc=ide-scsi ide_setup: ide0=ata66 ide_setup: hdc=ide-scsi Local APIC disabled by BIOS -- reenabling. Found and enabled local APIC! Initializing CPU#0 Detected 1470.058 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 2929.45 BogoMIPS Memory: 516580k/524288k available (1587k kernel code, 7324k reserved, 603k data, 224k init, 0k highmem) Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes) Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes) CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor = 2 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Machine check exception polling timer started. CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000 CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000 CPU: AMD Athlon(tm) XP processor 1700+ stepping 02 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 1469.9880 MHz. ..... host bus clock speed is 267.2704 MHz. cpu: 0, clocks: 2672704, slice: 1336352 CPU0 mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket PCI: PCI BIOS revision 2.10 entry at 0xfb4a0, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) Unknown bridge resource 0: assuming transparent PCI: Using IRQ router VIA [1106/0686] at 00:07.0 Applying VIA southbridge workaround. PCI: Disabling Via external APIC routing usb.c: registered new driver usbfs usb.c: registered new driver hub IA-32 Microcode Update Driver: v1.11 apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16) Starting kswapd BIO: pool of 256 setup, 14Kb (56 bytes/bio) biovec: init pool 0, 1 entries, 12 bytes biovec: init pool 1, 4 entries, 48 bytes biovec: init pool 2, 16 entries, 192 bytes biovec: init pool 3, 64 entries, 768 bytes biovec: init pool 4, 128 entries, 1536 bytes biovec: init pool 5, 256 entries, 3072 bytes devfs: v1.13 (20020406) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). parport0: PC-style at 0x378 [PCSPP(,...)] parport_pc: Via 686A parallel port: io=0x378 i2c-core.o: i2c core module i2c-dev.o: i2c /dev entries driver module i2c-core.o: driver i2c-dev dummy driver registered. i2c-algo-bit.o: i2c bit algorithm module i2c-proc.o version 2.6.1 (20010825) pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A lp0: using parport0 (polling). Real Time Clock Driver v1.11 Non-volatile memory driver v1.1 block: 256 slots per queue, batch=32 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Intel(R) PRO/100 Fast Ethernet Adapter - Loadable driver, ver 2.0.27-pre3 Copyright (c) 2002 Intel Corporation PCI: Found IRQ 11 for device 00:0d.0 PCI: Sharing IRQ 11 with 00:07.2 PCI: Sharing IRQ 11 with 00:07.3 PCI: Sharing IRQ 11 with 00:0b.0 eth0: Compaq Fast Ethernet Server Adapter Mem:0xe3203000 IRQ:11 Speed:100 Mbps Dx:Full Hardware receive checksums disabled Linux video capture interface: v1.00 Linux agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 440M agpgart: Detected Via Apollo Pro KT133 chipset agpgart: AGP aperture is 256M @ 0xc0000000 Uniform Multi-Platform E-IDE driver ver.:7.0.0 ide: system bus speed 33MHz VIA Technologies, Inc. Bus Master IDE: IDE controller on PCI slot 00:07.1 VIA Technologies, Inc. Bus Master IDE: chipset revision 6 VIA Technologies, Inc. Bus Master IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1 VIA Technologies, Inc. Bus Master IDE: warning: ATA-66/100 forced bit set! ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA hdc: LITE-ON LTR-16101B, ATAPI CD/DVD-ROM drive hdd: ASUS CD-S500/A, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hdd: ATAPI 50X CD-ROM drive, 128kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 SCSI subsystem driver Revision: 1.00 PCI: Found IRQ 11 for device 00:0b.0 PCI: Sharing IRQ 11 with 00:07.2 PCI: Sharing IRQ 11 with 00:07.3 PCI: Sharing IRQ 11 with 00:0d.0 scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.4 aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs (scsi0:A:0): 40.000MB/s transfers (20.000MHz, offset 63, 16bit) Vendor: IBM Model: DDYS-T18350N Rev: S93E Type: Direct-Access ANSI SCSI revision: 03 (scsi0:A:1): 40.000MB/s transfers (20.000MHz, offset 31, 16bit) Vendor: IBM Model: DNES-309170W Rev: SAH0 Type: Direct-Access ANSI SCSI revision: 03 (scsi0:A:6): 40.000MB/s transfers (20.000MHz, offset 31, 16bit) Vendor: IBM Model: DNES-309170W Rev: SAH0 Type: Direct-Access ANSI SCSI revision: 03 scsi0:A:0:0: Tagged Queuing enabled. Depth 253 scsi0:A:1:0: Tagged Queuing enabled. Depth 253 scsi0:A:6:0: Tagged Queuing enabled. Depth 253 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0 Attached scsi disk sdc at scsi0, channel 0, id 6, lun 0 SCSI device sda: 35843670 512-byte hdwr sectors (18352 MB) Partition check: /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 p8 p9 > SCSI device sdb: 17916240 512-byte hdwr sectors (9173 MB) /dev/scsi/host0/bus0/target1/lun0: p1 p2 SCSI device sdc: 17916240 512-byte hdwr sectors (9173 MB) /dev/scsi/host0/bus0/target6/lun0: p1 p2 md: raid0 personality registered as nr 2 md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 131072 bind 65536) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. found reiserfs format "3.6" with standard journal Reiserfs journal params: device 08:06, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (sd(8,6)) for (sd(8,6)) reiserfs: replayed 2 transactions in 0 seconds Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 224k freed Adding Swap: 514072k swap-space (priority 1) Adding Swap: 514072k swap-space (priority 1) NTFS driver 2.0.4 [Flags: R/O MODULE]. Copyright (c) 2001,2002 Anton Altaparmakov. uhci.c: USB Universal Host Controller Interface driver v1.1 PCI: Found IRQ 11 for device 00:07.2 PCI: Sharing IRQ 11 with 00:07.3 PCI: Sharing IRQ 11 with 00:0b.0 PCI: Sharing IRQ 11 with 00:0d.0 uhci.c: USB UHCI at I/O 0xd400, IRQ 11 hcd.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found at / hub.c: 2 ports detected PCI: Found IRQ 11 for device 00:07.3 PCI: Sharing IRQ 11 with 00:07.2 PCI: Sharing IRQ 11 with 00:0b.0 PCI: Sharing IRQ 11 with 00:0d.0 uhci.c: USB UHCI at I/O 0xd800, IRQ 11 hcd.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found at / hub.c: 2 ports detected mice: PS/2 mouse device common for all mice usb.c: registered new driver usb_mouse usbmouse.c: v1.6:USB HID Boot Protocol mouse driver usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.31:USB HID core driver [drm] AGP 0.99 on VIA Apollo KT133 @ 0xc0000000 256MB [drm] Initialized radeon 1.1.1 20010405 on minor 0 PCI: Found IRQ 5 for device 00:09.0 scsi1 : SCSI host adapter emulation for IDE ATAPI devices Vendor: LITE-ON Model: LTR-16101B Rev: TS0W Type: CD-ROM ANSI SCSI revision: 02 Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0 sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray [events: 00000068] [events: 00000068] [events: 00000068] md: autorun ... md: considering scsi/host0/bus0/target6/lun0/part1 ... md: adding scsi/host0/bus0/target6/lun0/part1 ... md: adding scsi/host0/bus0/target1/lun0/part1 ... md: adding scsi/host0/bus0/target0/lun0/part9 ... md: created md0 md: bind md: bind md: bind md: running: md: scsi/host0/bus0/target6/lun0/part1's event counter: 00000068 md: scsi/host0/bus0/target1/lun0/part1's event counter: 00000068 md: scsi/host0/bus0/target0/lun0/part9's event counter: 00000068 Unable to handle kernel NULL pointer dereference at virtual address 00000010 printing eip: c01e13f5 *pde = 00000000 Oops: 0000 CPU: 0 EIP: 0010:[] Not tainted EFLAGS: 00010202 eax: 00000000 ebx: c152fb14 ecx: c0395fc0 edx: 00000000 esi: 00000003 edi: df885000 ebp: c152fb00 esp: df287e08 ds: 0018 es: 0018 ss: 0018 Process raidstart (pid: 99, threadinfo=df286000 task=df825240) Stack: c152fb14 c023c79a 00000000 c0395fc0 00000002 c152fb00 c152fb00 00000001 c023ca16 c152fb00 df215900 c152fb14 c152fb00 df215900 00000008 000029a0 000029a0 c011ba29 000029a0 00000286 df286000 000029a0 000029a0 00000286 Call Trace: [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] Code: 0f b7 50 10 b2 00 66 0f b6 40 10 01 c2 89 d0 66 c1 e8 08 0f <3>error: raidstart[99] exited with preempt_count 1 hub.c: new USB device 00:07.2-1, assigned address 2 found reiserfs format "3.6" with standard journal Reiserfs journal params: device 08:07, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (sd(8,7)) for (sd(8,7)) reiserfs: replayed 1 transactions in 0 seconds Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device 08:08, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (sd(8,8)) for (sd(8,8)) reiserfs: replayed 1 transactions in 0 seconds Using r5 hash to sort names sh-2006: read_super_block: bread failed (dev md(9,0), block 8, size 1024) sh-2006: read_super_block: bread failed (dev md(9,0), block 64, size 1024) sh-2021: reiserfs_fill_super: can not find reiserfs on md(9,0) usb_control/bulk_msg: timeout input.c: calling /sbin/hotplug input [HOME=/ PATH=/sbin:/bin:/usr/sbin:/usr/bin ACTION=add PRODUCT=3/46d/c209/103 NAME=Logitech Inc. WingMan Gamepad] input.c: hotplug returned -2 input: USB HID v1.00 Joystick [Logitech Inc. WingMan Gamepad] on usb-00:07.2-1 spurious 8259A interrupt: IRQ7. hub.c: new USB device 00:07.2-2, assigned address 3 usb_control/bulk_msg: timeout input.c: calling /sbin/hotplug input [HOME=/ PATH=/sbin:/bin:/usr/sbin:/usr/bin ACTION=add PRODUCT=3/46d/c030/101 NAME=Logitech Inc. iFeel Mouse ] input.c: hotplug returned -2 input: USB HID v1.00 Mouse [Logitech Inc. iFeel Mouse ] on usb-00:07.2-2