I have booted 2.4.20-pre4 on another machine with a VIA chipset (ASUS A7V333) gcc-2.95.3 and just about everything the same. Regards Sid. On Tue, 2002-08-20 at 15:15, Sid Boyce wrote: > Thanks for the reply. I saw some posts about the VIA chipset and > wondered if they were related. During kernel/modules builds, I get a > number of warnings of various ideXXX.ver redefined. > Strange you are seeing this on the 845G chipset also. > Regards > Sid. > > On Tue, 2002-08-20 at 12:11, Tony Spinillo wrote: > > Sid, > > > > I just saw your post on linux-kernel. What chipset is your > > motherboard? > > I have had similiar problems. I'm using an 845G chipset board. > > 2.4.20pre1ac1 is also working well for me. The latest patches fail > > to pick up my IDE devices. > > > > They might be interested in seeing your lspci -vvv. Mine has been > > getting hits at http://ac.marywood.edu/tspin/www/lspci.txt > > since I posted it. > > > > -ac6 is supposed to have more fixes. > > > > Good luck! > > > > Tony > > > > > > > > > > > > > > > > > > > > > > __________________________________________________ > > Do You Yahoo!? > > HotJobs - Search Thousands of New Jobs > > http://www.hotjobs.com > -- > Sid Boyce ... hamradio G3VBV ... Cessna/Warrior Pilot > Linux only shop > ---- > > 00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266] > Subsystem: Asustek Computer, Inc.: Unknown device 807f > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0 > Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M] > Capabilities: [a0] AGP version 2.0 > Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2 > Command: RQ=0 SBA- AGP- 64bit- FW- Rate= > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT266 AGP] (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > Memory behind bridge: d6000000-d7dfffff > Prefetchable memory behind bridge: d7f00000-dfffffff > BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:09.0 USB Controller: VIA Technologies, Inc. UHCI USB (rev 50) (prog-if 00 [UHCI]) > Subsystem: Asustek Computer, Inc.: Unknown device 8080 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 32, cache line size 08 > Interrupt: pin A routed to IRQ 9 > Region 4: I/O ports at d800 [size=32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:09.1 USB Controller: VIA Technologies, Inc. UHCI USB (rev 50) (prog-if 00 [UHCI]) > Subsystem: Asustek Computer, Inc.: Unknown device 8080 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 32, cache line size 08 > Interrupt: pin B routed to IRQ 11 > Region 4: I/O ports at d400 [size=32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:09.2 USB Controller: VIA Technologies, Inc.: Unknown device 3104 (rev 51) (prog-if 20) > Subsystem: Asustek Computer, Inc.: Unknown device 8080 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 32, cache line size 08 > Interrupt: pin C routed to IRQ 10 > Region 0: Memory at d5800000 (32-bit, non-prefetchable) [size=256] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10) > Subsystem: Realtek Semiconductor Co., Ltd. RT8139 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 32 (8000ns min, 16000ns max) > Interrupt: pin A routed to IRQ 11 > Region 0: I/O ports at d000 [size=256] > Region 1: Memory at d5000000 (32-bit, non-prefetchable) [size=256] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:0e.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 08) > Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V, AudioPCI128 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- SERR- Latency: 32 (3000ns min, 32000ns max) > Interrupt: pin A routed to IRQ 10 > Region 0: I/O ports at b800 [size=64] > Capabilities: [dc] Power Management version 1 > Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:0f.0 SCSI storage controller: Adaptec AHA-2940/2940W / AIC-7871 (rev 03) > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 32 (2000ns min, 2000ns max), cache line size 08 > Interrupt: pin A routed to IRQ 5 > Region 0: I/O ports at b400 [disabled] [size=256] > Region 1: Memory at d4800000 (32-bit, non-prefetchable) [size=4K] > Expansion ROM at [disabled] [size=64K] > > 00:11.0 ISA bridge: VIA Technologies, Inc.: Unknown device 3147 > Subsystem: Asustek Computer, Inc.: Unknown device 808c > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0 > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) > Subsystem: Asustek Computer, Inc.: Unknown device 808c > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 32 > Interrupt: pin A routed to IRQ 0 > Region 4: I/O ports at b000 [size=16] > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:11.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 23) (prog-if 00 [UHCI]) > Subsystem: Asustek Computer, Inc.: Unknown device 808c > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 32, cache line size 08 > Interrupt: pin D routed to IRQ 9 > Region 4: I/O ports at a800 [size=32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:11.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 23) (prog-if 00 [UHCI]) > Subsystem: Asustek Computer, Inc.: Unknown device 808c > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 32, cache line size 08 > Interrupt: pin D routed to IRQ 9 > Region 4: I/O ports at a400 [size=32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 01:00.0 VGA compatible controller: nVidia Corporation NV11 (GeForce2 MX) (rev b2) (prog-if 00 [VGA]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 64 (1250ns min, 250ns max) > Interrupt: pin A routed to IRQ 11 > Region 0: Memory at d6000000 (32-bit, non-prefetchable) [size=16M] > Region 1: Memory at d8000000 (32-bit, prefetchable) [size=128M] > Expansion ROM at d7ff0000 [disabled] [size=64K] > Capabilities: [60] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [44] AGP version 2.0 > Status: RQ=31 SBA- 64bit- FW+ Rate=x1,x2 > Command: RQ=0 SBA- AGP- 64bit- FW- Rate= > -- Sid Boyce ... hamradio G3VBV ... Cessna/Warrior Pilot Linux only shop