mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Robert Love <rml@tech9.net>
To: torvalds@transmeta.com
Cc: linux-kernel@vger.kernel.org
Subject: [PATCH] hyperthreading scheduler improvement
Date: 26 Aug 2002 16:05:36 -0400	[thread overview]
Message-ID: <1030392337.15007.413.camel@phantasy> (raw)

Linus,

This patch implements a per-arch load balancing scheme for P4s to better
balance across the virtual CPUs (e.g. prefer fully unused CPUs to a
single available HT unit).  This is the same logic in 2.4-ac, 2.4-aa,
etc.

This patch uses the previously posted per-arch load balancing
infrastructure.

The new logic is keyed off of a new CONFIG_X86_HYPERTHREADING value
which is currently set off of CONFIG_MPENTIUM4.  Thus, only kernels
compiled for P4s will receive the new logic.  It is safe to make the
code available to all x86s, however.

As I am not fortunate enough to have dual Xeons at my disposal, this
patch is largely untested for performance, although it is present in -aa
and -ac.  I suspect this could show very acceptable performance gains.

	Robert Love

diff -urN linux-2.5.31/arch/i386/config.in linux/arch/i386/config.in
--- linux-2.5.31/arch/i386/config.in	Sat Aug 10 21:41:25 2002
+++ linux/arch/i386/config.in	Sat Aug 24 22:07:10 2002
@@ -103,6 +103,7 @@
    define_bool CONFIG_X86_TSC y
    define_bool CONFIG_X86_GOOD_APIC y
    define_bool CONFIG_X86_USE_PPRO_CHECKSUM y
+   define_bool CONFIG_X86_HYPERTHREADING y
 fi
 if [ "$CONFIG_MK6" = "y" ]; then
    define_int  CONFIG_X86_L1_CACHE_SHIFT 5
diff -urN linux-2.5.31/include/asm-i386/processor.h linux/include/asm-i386/processor.h
--- linux-2.5.31/include/asm-i386/processor.h	Sat Aug 10 21:41:18 2002
+++ linux/include/asm-i386/processor.h	Sat Aug 24 22:07:10 2002
@@ -488,4 +488,6 @@
 
 #endif
 
+#define ARCH_HAS_SMP_BALANCE
+
 #endif /* __ASM_I386_PROCESSOR_H */
diff -urN linux-2.5.31/include/asm-i386/smp_balance.h linux/include/asm-i386/smp_balance.h
--- linux-2.5.31/include/asm-i386/smp_balance.h	Wed Dec 31 19:00:00 1969
+++ linux/include/asm-i386/smp_balance.h	Sat Aug 24 22:26:15 2002
@@ -0,0 +1,55 @@
+#ifndef _ASM_SMP_BALANCE_H
+#define _ASM_SMP_BALANCE_H
+
+/*
+ * We have an architecture-specific SMP load balancer to improve
+ * scheduling behavior on hyperthreaded CPUs.  Since only P4s have
+ * HT, we only use the code if CONFIG_MPENTIUM4 is set.
+ *
+ * Distributions may want to make this unconditional to support all
+ * x86 machines on one kernel.  The overhead in the non-P4 case is
+ * minimal while the benefit to SMP P4s is probably decent.
+ */
+#if defined(CONFIG_X86_HYPERTHREADING)
+
+/*
+ * Find any idle processor package (i.e. both virtual processors are idle)
+ */
+static inline int find_idle_package(int this_cpu)
+{
+	int i;
+
+	i = this_cpu;
+
+	for (i = (this_cpu + 1) % NR_CPUS;
+	     i != this_cpu;
+	     i = (i + 1) % NR_CPUS) {
+		int sibling = cpu_sibling_map[i];
+
+		if (idle_cpu(i) && idle_cpu(sibling))
+			return i;
+	}
+	return -1;	/* not found */
+}
+
+static inline int arch_load_balance(int this_cpu, int idle)
+{
+	/* Special hack for hyperthreading */
+       if (unlikely(smp_num_siblings > 1 && idle && !idle_cpu(cpu_sibling_map[this_cpu]))) {
+               int found;
+               struct runqueue *rq_target;
+
+               if ((found = find_idle_package(this_cpu)) >= 0 ) {
+                       rq_target = cpu_rq(found);
+                       resched_task(rq_target->idle);
+                       return 1;
+               }
+       }
+       return 0;
+}
+
+#else
+#define arch_load_balance(x, y)		(0)
+#endif
+
+#endif /* _ASM_SMP_BALANCE_H */




             reply	other threads:[~2002-08-26 20:01 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2002-08-26 20:05 Robert Love [this message]
2002-08-26 20:15 ` Alan Cox
2002-08-26 20:25   ` Robert Love
2002-08-26 20:35     ` Alan Cox
2002-08-26 20:40       ` Robert Love
2002-08-26 20:53 ` Robert Love

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1030392337.15007.413.camel@phantasy \
    --to=rml@tech9.net \
    --cc=linux-kernel@vger.kernel.org \
    --cc=torvalds@transmeta.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®