From: Jurgen Kramer <gtm.kramer@inter.nl.net>
To: Mario Lang <mlang@delysid.org>
Cc: linux-kernel@vger.kernel.org
Subject: Re: PROBLEM: JVC MP-XP7210 hangs on boot with 2.6.0-test4
Date: Sat, 30 Aug 2003 10:56:31 +0200 [thread overview]
Message-ID: <1062233791.1482.2.camel@paragon.slim> (raw)
In-Reply-To: <87k78wsip0.fsf@lexx.delysid.org>
OK, I've tried 2.6.0-test4 on my XP7210 and it works just
happily. Everything is working: ACPI, PCMCIA, ALSA, SISFB the works...
Maybe it's your version of GCC? I use GCC 3.2.2 which comes with RH9.
Cheers,
Jurgen
On Fri, 2003-08-29 at 15:21, Mario Lang wrote:
> Hi.
>
> I just tried 2.6.0-test4 on my Laptop (JVC MP-XP7210, 256MB RAM, IDE).
> However, it hangs on boot. I tried booting with acpi=off and also
> with "acpi=off noapic". Both options seem to help nothing,
> and the same output appears on all attempts to boot.
>
> I compiled the kernel with gcc 3.3.2.
>
> Here is the output I get:
>
> [<c0 10 92 69>] Kernel_thread_helper+0x5/0xc
> Code: 0f ba 6e 24 00 c7 44 24 04 00 00 00 00 89 34 24 e8 25 fa ff
> <0> Kernel Panic: Fatal Exception in Interrupt
> in interrupt handler - not syncing
>
> (and here it hangs)
>
> P.S.: I am not subscribed, please CC.
>
> Here is also the output of lspci -vv run under 2.4.20-pre7-acpi:
>
> 00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 31)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 32
> Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=64M]
> Capabilities: [c0] AGP version 2.0
> Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
>
> 00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) (prog-if 80 [Master])
> Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 16
> Region 4: I/O ports at d800 [size=16]
>
> 00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:01.1 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet (rev 82)
> Subsystem: Asustek Computer, Inc.: Unknown device 1455
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (13000ns min, 2750ns max)
> Interrupt: pin C routed to IRQ 5
> Region 0: I/O ports at d400 [size=256]
> Region 1: Memory at d3800000 (32-bit, non-prefetchable) [size=4K]
> Expansion ROM at <unassigned> [disabled] [size=128K]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=160mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:01.2 USB Controller: Silicon Integrated Systems [SiS] SiS7001 USB Controller (rev 07) (prog-if 10 [OHCI])
> Subsystem: Silicon Integrated Systems [SiS] SiS7001 USB Controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), cache line size 08
> Interrupt: pin D routed to IRQ 4
> Region 0: Memory at d3000000 (32-bit, non-prefetchable) [size=4K]
>
> 00:01.3 USB Controller: Silicon Integrated Systems [SiS] SiS7001 USB Controller (rev 07) (prog-if 10 [OHCI])
> Subsystem: Silicon Integrated Systems [SiS] Onboard USB Controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (20000ns max), cache line size 08
> Interrupt: pin D routed to IRQ 4
> Region 0: Memory at d2800000 (32-bit, non-prefetchable) [size=4K]
>
> 00:01.4 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator (rev 02)
> Subsystem: Asustek Computer, Inc.: Unknown device 1473
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (500ns min, 6000ns max)
> Interrupt: pin B routed to IRQ 7
> Region 0: I/O ports at d000 [size=256]
> Region 1: Memory at d2000000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=55mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:01.6 Modem: Silicon Integrated Systems [SiS] Intel 537 [56k Winmodem] (rev a0) (prog-if 00 [Generic])
> Subsystem: Asustek Computer, Inc.: Unknown device 1616
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (13000ns min, 2750ns max)
> Interrupt: pin C routed to IRQ 5
> Region 0: I/O ports at b800 [size=256]
> Region 1: I/O ports at b400 [size=128]
> Capabilities: [48] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:02.0 PCI bridge: Silicon Integrated Systems [SiS] SiS 530 Virtual PCI-to-PCI bridge (AGP) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 0000a000-0000afff
> Memory behind bridge: d1800000-d1ffffff
> Prefetchable memory behind bridge: d8000000-e7efffff
> BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
>
> 00:09.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 88)
> Subsystem: Asustek Computer, Inc.: Unknown device 1674
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 168
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at 000de000 (32-bit, non-prefetchable) [size=4K]
> Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
> Memory window 0: 10400000-107ff000 (prefetchable)
> Memory window 1: 10800000-10bff000
> I/O window 0: 00004000-000040ff
> I/O window 1: 00004400-000044ff
> BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
> 16-bit legacy interface ports at 0001
>
> 00:09.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 88)
> Subsystem: Asustek Computer, Inc.: Unknown device 1674
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 168
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
> Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
> Memory window 0: 10c00000-10fff000 (prefetchable)
> Memory window 1: 11000000-113ff000
> I/O window 0: 00004800-000048ff
> I/O window 1: 00004c00-00004cff
> BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
> 16-bit legacy interface ports at 0001
>
> 00:09.2 System peripheral: Ricoh Co Ltd: Unknown device 0576
> Subsystem: Asustek Computer, Inc.: Unknown device 1674
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at 10001000 (32-bit, non-prefetchable) [disabled] [size=256]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME+
>
> 00:0a.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
> Subsystem: Asustek Computer, Inc.: Unknown device 1677
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (500ns min, 1000ns max), cache line size 08
> Interrupt: pin A routed to IRQ 4
> Region 0: Memory at d1000000 (32-bit, non-prefetchable) [size=2K]
> Region 1: Memory at d0800000 (32-bit, non-prefetchable) [size=16K]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME+
>
> 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] SiS630 GUI Accelerator+3D (rev 31) (prog-if 00 [VGA])
> Subsystem: Asustek Computer, Inc.: Unknown device 1672
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> BIST result: 00
> Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
> Region 1: Memory at d1800000 (32-bit, non-prefetchable) [size=128K]
> Region 2: I/O ports at a800 [size=128]
> Capabilities: [40] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] AGP version 2.0
> Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
>
prev parent reply other threads:[~2003-08-30 8:57 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-08-29 13:21 Mario Lang
2003-08-29 16:48 ` Andrew Morton
2003-09-03 11:54 ` Mario Lang
2003-08-29 19:50 ` Jurgen Kramer
2003-08-30 8:56 ` Jurgen Kramer [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1062233791.1482.2.camel@paragon.slim \
--to=gtm.kramer@inter.nl.net \
--cc=linux-kernel@vger.kernel.org \
--cc=mlang@delysid.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome