000, IRQ 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI BALANCE SET ACPI: MCFG not present Using ACPI (MADT) for SMP configuration information Built 1 zonelists current: c038ba60 current->thread_info: c0416000 Initializing CPU#0 Kernel command line: BOOT_IMAGE=Linux ro root=303 2.6 Unknown boot option `2.6': ignoring PID hash table entries: 2048 (order 11: 16384 bytes) Detected 2004.923 MHz processor. Using pmtmr for high-res timesource Console: colour dummy device 80x25 Memory: 514760k/524224k available (2120k kernel code, 8700k reserved, 1036k data, 160k init, 0k highmem) Calibrating delay loop... 3973.12 BogoMIPS Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: After all inits, caps: 3febfbff 00000000 00000000 00000080 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available CPU#0: Thermal monitoring enabled CPU: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 04 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=-1 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2004.0263 MHz. ..... host bus clock speed is 100.0213 MHz. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfdb81, last bus=3 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040116 IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9 Mode:1 Active:0) ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICHB._PRT] ACPI: Power Resource [URP1] (off) ACPI: Power Resource [URP2] (off) ACPI: Power Resource [FDDP] (off) ACPI: Power Resource [LPTP] (off) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs *11) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 11) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 *12 14 15) drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub IOAPIC[0]: Set PCI routing entry (2-18 -> 0xa9 -> IRQ 18 Mode:1 Active:1) 00:00:1f[A] -> 2-18 -> IRQ 18 IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17 Mode:1 Active:1) 00:00:1f[B] -> 2-17 -> IRQ 17 IOAPIC[0]: Set PCI routing entry (2-16 -> 0xb9 -> IRQ 16 Mode:1 Active:1) 00:00:1d[A] -> 2-16 -> IRQ 16 IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19 Mode:1 Active:1) 00:00:1d[B] -> 2-19 -> IRQ 19 Pin 2-18 already programmed IOAPIC[0]: Set PCI routing entry (2-23 -> 0xc9 -> IRQ 23 Mode:1 Active:1) 00:00:1d[D] -> 2-23 -> IRQ 23 Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed IOAPIC[0]: Set PCI routing entry (2-22 -> 0xd1 -> IRQ 22 Mode:1 Active:1) 00:03:0e[A] -> 2-22 -> IRQ 22 IOAPIC[0]: Set PCI routing entry (2-20 -> 0xd9 -> IRQ 20 Mode:1 Active:1) 00:03:08[A] -> 2-20 -> IRQ 20 number of MP IRQ sources: 15. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020 .... register #02: 00000000 ....... : arbitration: 00 .... register #03: 00000001 ....... : Boot DT : 1 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 0 1 0 0 0 1 1 71 0a 001 01 0 0 0 0 0 1 1 79 0b 001 01 0 0 0 0 0 1 1 81 0c 001 01 0 0 0 0 0 1 1 89 0d 001 01 0 0 0 0 0 1 1 91 0e 001 01 0 0 0 0 0 1 1 99 0f 001 01 0 0 0 0 0 1 1 A1 10 001 01 1 1 0 1 0 1 1 B9 11 001 01 1 1 0 1 0 1 1 B1 12 001 01 1 1 0 1 0 1 1 A9 13 001 01 1 1 0 1 0 1 1 C1 14 001 01 1 1 0 1 0 1 1 D9 15 000 00 1 0 0 0 0 0 0 00 16 001 01 1 1 0 1 0 1 1 D1 17 001 01 1 1 0 1 0 1 1 C9 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9-> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 0:16 IRQ17 -> 0:17 IRQ18 -> 0:18 IRQ19 -> 0:19 IRQ20 -> 0:20 IRQ22 -> 0:22 IRQ23 -> 0:23 .................................... done. PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' Bluetooth: Core ver 2.3 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized vesafb: framebuffer at 0xd0000000, mapped to 0xe080b000, size 16384k vesafb: mode is 1280x1024x8, linelength=1280, pages=1 vesafb: protected mode interface info at c000:e1b0 vesafb: scrolling: redraw fb0: VESA VGA frame buffer device Machine check exception polling timer started. apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 NTFS driver 2.1.6 [Flags: R/O]. udf: registering filesystem ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] ACPI: Processor [CPU1] (supports C1, 8 throttling states) Console: switching to colour frame buffer device 160x64 pty: 256 Unix98 ptys configured Real Time Clock Driver v1.12 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected an Intel i845 Chipset. agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 128M @ 0xe0000000 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Using anticipatory io scheduler Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH4: IDE controller at PCI slot 0000:00:1f.1 ICH4: chipset revision 1 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA hda: IC35L120AVVA07-0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: LG DVD-ROM DRD-8160B, ATAPI CD/DVD-ROM drive hdd: Hewlett-Packard DVD Writer 200, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100) /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 hdc: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 hdd: ATAPI 32X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) ohci1394: $Rev: 1097 $ Ben Collins ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[dfefb000-dfefb7ff] Max Packet=[2048] video1394: Installed video1394 module raw1394: /dev/raw1394 device initialized eth1394: $Rev: 1096 $ Ben Collins eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (ohci1394) ieee1394: Loaded AMDTP driver ieee1394: Loaded CMP driver Console: switching to colour frame buffer device 160x64 ehci_hcd 0000:00:1d.7: EHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: irq 23, pci mem e1854c00 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 PCI: cache line size of 128 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29 hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1 uhci_hcd 0000:00:1d.0: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: irq 16, io base 0000d400 uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.1: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: irq 19, io base 0000d800 uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c003100c674] Badness in kobject_get at lib/kobject.c:431 Call Trace: [] kobject_get+0x4c/0x4e hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.2: UHCI Host Controller [] get_device+0x18/0x21 [] bus_for_each_dev+0x63/0xba [] nodemgr_node_probe+0x4d/0x124 [] nodemgr_probe_ne_cb+0x0/0x8d [] nodemgr_host_thread+0x17d/0x1a1 [] nodemgr_host_thread+0x0/0x1a1 [] kernel_thread_helper+0x5/0xb Unable to handle kernel paging request at virtual address b828ec83 printing eip: b828ec83 *pde = 00000000 Oops: 0000 [#1] PREEMPT CPU: 0 EIP: 0060:[] Not tainted VLI EFLAGS: 00010282 EIP is at 0xb828ec83 eax: b828ec83 ebx: c03cc3e4 ecx: dfd67f9c edx: 00000000 esi: c0263975 edi: 00000000 ebp: c02626d4 esp: dfd67f40 ds: 007b es: 007b ss: 0068 Process knodemgrd_0 (pid: 10, threadinfo=dfd66000 task=dfe08100) Stack: c01e3150 c03cc3e4 c03cc3c0 c03cc3c8 c03cc320 dfcf3c44 c022fb70 c03cc3e4 dfd67f9c c03cc36c 00000000 dfcf3c3c dfd67f9c dfd63a18 dfd67f9c c0264094 c03cc320 dfcf3c3c dfd67f9c c0263f5d dff94000 dfd63a18 dff94000 dfd63a18 Call Trace: [] kobject_cleanup+0x98/0x9a [] bus_for_each_dev+0x80/0xba [] nodemgr_node_probe+0x4d/0x124 [] nodemgr_probe_ne_cb+0x0/0x8d [] nodemgr_host_thread+0x17d/0x1a1 [] nodemgr_host_thread+0x0/0x1a1 [] kernel_thread_helper+0x5/0xb Code: Bad EIP value. <7>PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: irq 18, io base 0000dc00 uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected drivers/usb/core/usb.c: registered new driver hiddev drivers/usb/core/usb.c: registered new driver hid drivers/usb/input/hid-core.c: v2.0:USB HID core driver mice: PS/2 mouse device common for all mice serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 Bluetooth: HCI USB driver ver 2.4 drivers/usb/core/usb.c: registered new driver hci_usb NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) NET: Registered protocol family 1 NET: Registered protocol family 17 Bluetooth: L2CAP ver 2.1 Bluetooth: L2CAP socket layer initialized Bluetooth: SCO (Voice Link) ver 0.3 Bluetooth: SCO socket layer initialized Bluetooth: RFCOMM ver 1.1 Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: BNEP (Ethernet Emulation) ver 1.0 Bluetooth: BNEP filters: protocol multicast found reiserfs format "3.6" with standard journal hub 2-0:1.0: new USB device on port 2, assigned address 2 input: USB HID v1.10 Mouse [Microsoft Microsoft Wireless Intellimouse Explorer® 1.0A] on usb-0000:00:1d.0-2 hub 4-0:1.0: new USB device on port 1, assigned address 2 Reiserfs journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (hda3) for (hda3) Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 160k freed blk: queue dfda9a00, I/O limit 4095Mb (mask 0xffffffff) hdc: CHECK for good STATUS hdd: CHECK for good STATUS Adding 514044k swap on /dev/hda2. Priority:-1 extents:1 8139too Fast Ethernet driver 0.9.27 eth1: RealTek RTL8139 at 0xe194cf00, 00:50:fc:9c:f7:27, IRQ 18 eth1: Identified 8139 chip type 'RTL-8100B/8139D' e100: Intel(R) PRO/100 Network Driver, 3.0.13_dev e100: Copyright(c) 1999-2004 Intel Corporation e100: eth2: e100_probe: addr 0xdfefa000, irq 20, MAC addr 00:10:DC:50:AD:95 NTFS volume version 3.1. e100: eth2: e100_watchdog: link up, 10Mbps, half-duplex nvidia: module license 'NVIDIA' taints kernel. 0: nvidia: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-5336 Wed Jan 14 18:29:26 PST 2004 agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly. atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.