On Sun, 2004-07-18 at 13:48, Jens Olav Nygaard wrote: 
> > From: Jurgen Kramer <gtm.kramer@inter.nl.net>
> 
> >>Just gave it a try. My EHCI controller is still failing (Asus P4C800-E
> >>i875p) as in the 2.6.7-mm series.
> >>
> >><snip>
> >>ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
> >>ehci_hcd 0000:00:1d.7: EHCI Host Controller
> >>ehci_hcd 0000:00:1d.7: BIOS handoff failed (104, 1010001)
> >>ehci_hcd 0000:00:1d.7: can't reset
> >>ehci_hcd 0000:00:1d.7: init 0000:00:1d.7 fail, -95
> >>ehci_hcd: probe of 0000:00:1d.7 failed with error -95
> >>USB Universal Host Controller Interface driver v2.2
> >><snip>
> 
> This is also what I see (on my Asus P4P800) more or less:
> 
> ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
> ehci_hcd 0000:00:1d.7: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller
> ehci_hcd 0000:00:1d.7: BIOS handoff failed (104, 1010001)
> ehci_hcd 0000:00:1d.7: can't reset
> ehci_hcd 0000:00:1d.7: init 0000:00:1d.7 fail, -95
> ehci_hcd: probe of 0000:00:1d.7 failed with error -95
> 
> The funny thing is, it has happened with various kernel snapshots
> (right term for the 2.6.7-bk??-patches?) but not all.
> I thought I had one (2.6.7-bk17) which didn't give this response,
> but now it does, and I suspect the problem is really something else.
> (Some automatic irq assignment to usb-hardware?)
> 
> I'm not into kernel source hacking so I can't really say much more.
> 
> Jurriaan:
> 
> > That is most probably something in your bios. My Epox 4PCA3+ (also i875
> > chipset) says:
> 
> Then it's in mine also.

As I said in previous mail, my p4c800-e dlx works fine:

--- 
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
ehci_hcd 0000:00:1d.7: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 193, pci mem f9968c00
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
---

You using the latest bios version?  Maybe check if there is a beta
bios available ?

I saw somebody said newer bios versions do not work (Locks after
ACPI init).  I am not sure if this is related, but for our boards
you do not want ISAPNP or PNPBIOS, just ACPI (it used to oops at
some stage - either after ACPI init or PNP init), and I did enable
CONFIG_PNP ...

---
# grep PNP .config
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set
# CONFIG_ISAPNP is not set
# CONFIG_PNPBIOS is not set
# CONFIG_BLK_DEV_IDEPNP is not set
# CONFIG_IP_PNP is not set
---


-- 
Martin Schlemmer