From: Andreas Junge <ajunge@penguincomputing.com>
To: linux-kernel@vger.kernel.org
Subject: RE:x86_64 Opteron dual core panics on boot
Date: Mon, 13 Jun 2005 10:48:07 -0700 [thread overview]
Message-ID: <1118684887.19967.12.camel@jellyfish.highlyscyld.com> (raw)
FYI, we have the same kernel panic as described in Tom Duffy's message
when booting our dual (not dual core) Opteron 248's. About one in ten
boots ends up in a kernel panic.
Andreas Junge
-------------------------
Bootdata ok (command line is ro root=LABEL=/ rhgb console=ttyS0,38400n8
console=tty0 debug)
Linux version 2.6.11-1.27_FC3smp (bhcompile@crowe.devel.redhat.com) (gcc
version 3.4.3 20050227 (Red Hat 3.4.3-22)) #1 SMP Tue May 17 20:38:05
EDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bfff0000 (usable)
BIOS-e820: 00000000bfff0000 - 00000000bfffe000 (ACPI data)
BIOS-e820: 00000000bfffe000 - 00000000c0000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
ACPI: RSDP (v000 ACPIAM ) @
0x00000000000f7f00
ACPI: RSDT (v001 A M I OEMRSDT 0x04000520 MSFT 0x00000097) @
0x00000000bfff0000
ACPI: FADT (v002 A M I OEMFACP 0x04000520 MSFT 0x00000097) @
0x00000000bfff0200
ACPI: MADT (v001 A M I OEMAPIC 0x04000520 MSFT 0x00000097) @
0x00000000bfff0390
ACPI: OEMB (v001 A M I AMI_OEM 0x04000520 MSFT 0x00000097) @
0x00000000bfffe040
ACPI: SRAT (v001 A M I OEMSRAT 0x04000520 MSFT 0x00000097) @
0x00000000bfff4520
ACPI: DSDT (v001 TUNA_ TUNA_110 0x00000110 INTL 0x02002026) @
0x0000000000000000
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 1 -> APIC 1 -> Node 1
SRAT: Node 0 PXM 0 100000-7fffffff
SRAT: Node 1 PXM 1 80000000-bfffffff
SRAT: Node 0 PXM 0 0-7fffffff
Bootmem setup node 0 0000000000000000-000000007fffffff
Bootmem setup node 1 0000000080000000-00000000bfffffff
On node 0 totalpages: 524287
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 520191 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
On node 1 totalpages: 262143
DMA zone: 0 pages, LIFO batch:1
Normal zone: 262143 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
Nvidia board detected. Ignoring ACPI timer override.
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:5 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:5 APIC version 16
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfebff000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 17, address 0xfebff000, GSI 24-27
ACPI: IOAPIC (id[0x04] address[0xfebfe000] gsi_base[28])
IOAPIC[2]: apic_id 4, version 17, address 0xfebfe000, GSI 28-31
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Checking aperture...
CPU 0: aperture @ 4000000 size 32 MB
Aperture from northbridge cpu 0 too small (32 MB)
No AGP bridge found
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
Built 2 zonelists
Kernel command line: ro root=LABEL=/ rhgb console=ttyS0,38400n8
console=tty0 debug
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 2211.365 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Memory: 3024176k/5242880k available (2317k kernel code, 0k reserved,
1224k data, 220k init)
Calibrating delay loop... 4308.99 BogoMIPS (lpj=2154496)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0(1) -> Node 0
Using local APIC NMI watchdog using perfctr0
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0(1) -> Node 0
CPU0: AMD Opteron(tm) Processor 248 stepping 0a
per-CPU timeslice cutoff: 1023.91 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 rip 6000 rsp ffff810081447f58
Initializing CPU#1
Calibrating delay loop... <7>spurious 8259A interrupt: IRQ7.
----------- [cut here ] --------- [please bite here ] ---------
Kernel BUG at timer:418
invalid operand: 0000 [1] SMP
CPU 1
Modules linked in:
Pid: 0, comm: swapper Not tainted 2.6.11-1.27_FC3smp
RIP: 0010:[<ffffffff80141c3e>] <ffffffff80141c3e>{cascade+46}
RSP: 0018:ffff810002c17ed0 EFLAGS: 00010087
reply other threads:[~2005-06-13 17:52 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1118684887.19967.12.camel@jellyfish.highlyscyld.com \
--to=ajunge@penguincomputing.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®