From: john stultz <johnstul@us.ibm.com>
To: Ingo Molnar <mingo@elte.hu>
Cc: lkml <linux-kernel@vger.kernel.org>,
rusty@rustcorp.com.au, jakub@redhat.com
Subject: [BUG] futex_handle_fault always fails.
Date: Mon, 07 Aug 2006 14:39:58 -0700 [thread overview]
Message-ID: <1154986798.5343.26.camel@localhost.localdomain> (raw)
We found this issue last week w/ the -RT kernel, but it seems the same
issue is in mainline as well.
Basically is possible for futex_unlock_pi to return without actually
freeing the lock. This is due to buggy logic in the use of
futex_handle_fault() and its attempt argument in a failure case.
Looking at futex.c the logic is as follows:
1) In futex_unlock_pi() we start w/ ret=0 and we go down to the first
futex_atomic_cmpxchg_inatomic(), where we find uval==-EFAULT. We then
jump to the pi_faulted label.
2) From pi_faulted: We increment attempt, unlock the sem and hit the
retry label.
3) From the retry label, with ret still zero, we again hit EFAULT on the
first futex_atomic_cmpxchg_inatomic(), and again goto the pi_faulted
label.
4) Again from pi_faulted: we increment attempt and enter the
conditional, where we call futex_handle_fault.
5) futex_handle_fault fails, and we goto the out_unlock_release_sem
label.
6) From out_unlock_release_sem we return, and since ret is still zero,
we return without error, while never actually unlocking the lock.
Issue #1: at the first futex_atomic_cmpxchg_inatomic() we should
probably be setting ret=-EFAULT before jumping to pi_faulted: However
in our case this doesn't really affect anything, as the glibc we're
using ignores the error value from futex_unlock_pi().
Issue #2: Look at futex_handle_fault(), its first conditional will
return -EFAULT if attempt is >= 2. However, from the "if(attempt++)
futex_handle_fault(attempt)" logic above, we'll *never* call
futex_handle_fault when attempt is less then two. So we never get a
chance to even try to fault the page in.
The following patch addresses these two issues by 1) Always setting ret
to -EFAULT if futex_handle_fault fails, and 2) Removing the = in
futex_handle_fault's (attempt >= 2) check.
I'm really not sure this is the right fix, but wanted to bring it up so
folks knew the issue is alive and well in the current -git tree. From
looking at the git logs the logic was first introduced (then later
copied to other places) in the following commit almost a year ago:
http://www.kernel.org/git/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=4732efbeb997189d9f9b04708dc26bf8613ed721;hp=5b039e681b8c5f30aac9cc04385cc94be45d0823
Thoughts, comments?
thanks
-john
diff --git a/kernel/futex.c b/kernel/futex.c
index c2b2e0b..d4633c5 100644
--- a/kernel/futex.c
+++ b/kernel/futex.c
@@ -297,7 +297,7 @@ static int futex_handle_fault(unsigned l
struct vm_area_struct * vma;
struct mm_struct *mm = current->mm;
- if (attempt >= 2 || !(vma = find_vma(mm, address)) ||
+ if (attempt > 2 || !(vma = find_vma(mm, address)) ||
vma->vm_start > address || !(vma->vm_flags & VM_WRITE))
return -EFAULT;
@@ -747,8 +747,10 @@ retry:
*/
if (attempt++) {
if (futex_handle_fault((unsigned long)uaddr2,
- attempt))
+ attempt)) {
+ ret = -EFAULT;
goto out;
+ }
goto retry;
}
@@ -1322,9 +1324,10 @@ static int do_futex_lock_pi(u32 __user *
* still holding the mmap_sem.
*/
if (attempt++) {
- if (futex_handle_fault((unsigned long)uaddr, attempt))
+ if (futex_handle_fault((unsigned long)uaddr, attempt)) {
+ ret = -EFAULT;
goto out_unlock_release_sem;
-
+ }
goto retry_locked;
}
@@ -1506,9 +1509,10 @@ pi_faulted:
* still holding the mmap_sem.
*/
if (attempt++) {
- if (futex_handle_fault((unsigned long)uaddr, attempt))
+ if (futex_handle_fault((unsigned long)uaddr, attempt)) {
+ ret = -EFAULT;
goto out_unlock;
-
+ }
goto retry_locked;
}
next reply other threads:[~2006-08-07 21:40 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-08-07 21:39 john stultz [this message]
2006-08-08 8:38 ` Mike Galbraith
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1154986798.5343.26.camel@localhost.localdomain \
--to=johnstul@us.ibm.com \
--cc=jakub@redhat.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mingo@elte.hu \
--cc=rusty@rustcorp.com.au \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome