From: Daniel Golle <daniel@makrotopia.org>
To: Pavel Machek <pavel@ucw.cz>, Lee Jones <lee@kernel.org>,
Andrew Lunn <andrew@lunn.ch>,
Christian Marangi <ansuelsmth@gmail.com>,
"David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Daniel Golle <daniel@makrotopia.org>,
Li Zetao <lizetao1@huawei.com>,
linux-leds@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH v2] leds: trigger: netdev: extend speeds up to 10G
Date: Sun, 26 Nov 2023 22:07:18 +0000 [thread overview]
Message-ID: <120eddc938b588622020822510e3c19a4d169686.1701035950.git.daniel@makrotopia.org> (raw)
Add 2.5G, 5G and 10G as available speeds to the netdev LED trigger.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
v2: add missing sysfs entries
drivers/leds/trigger/ledtrig-netdev.c | 32 ++++++++++++++++++++++++++-
include/linux/leds.h | 3 +++
2 files changed, 34 insertions(+), 1 deletion(-)
diff --git a/drivers/leds/trigger/ledtrig-netdev.c b/drivers/leds/trigger/ledtrig-netdev.c
index e358e77e4b38f..bd68da15c723e 100644
--- a/drivers/leds/trigger/ledtrig-netdev.c
+++ b/drivers/leds/trigger/ledtrig-netdev.c
@@ -99,6 +99,18 @@ static void set_baseline_state(struct led_netdev_data *trigger_data)
trigger_data->link_speed == SPEED_1000)
blink_on = true;
+ if (test_bit(TRIGGER_NETDEV_LINK_2500, &trigger_data->mode) &&
+ trigger_data->link_speed == SPEED_2500)
+ blink_on = true;
+
+ if (test_bit(TRIGGER_NETDEV_LINK_5000, &trigger_data->mode) &&
+ trigger_data->link_speed == SPEED_5000)
+ blink_on = true;
+
+ if (test_bit(TRIGGER_NETDEV_LINK_10000, &trigger_data->mode) &&
+ trigger_data->link_speed == SPEED_10000)
+ blink_on = true;
+
if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &trigger_data->mode) &&
trigger_data->duplex == DUPLEX_HALF)
blink_on = true;
@@ -286,6 +298,9 @@ static ssize_t netdev_led_attr_show(struct device *dev, char *buf,
case TRIGGER_NETDEV_LINK_10:
case TRIGGER_NETDEV_LINK_100:
case TRIGGER_NETDEV_LINK_1000:
+ case TRIGGER_NETDEV_LINK_2500:
+ case TRIGGER_NETDEV_LINK_5000:
+ case TRIGGER_NETDEV_LINK_10000:
case TRIGGER_NETDEV_HALF_DUPLEX:
case TRIGGER_NETDEV_FULL_DUPLEX:
case TRIGGER_NETDEV_TX:
@@ -316,6 +331,9 @@ static ssize_t netdev_led_attr_store(struct device *dev, const char *buf,
case TRIGGER_NETDEV_LINK_10:
case TRIGGER_NETDEV_LINK_100:
case TRIGGER_NETDEV_LINK_1000:
+ case TRIGGER_NETDEV_LINK_2500:
+ case TRIGGER_NETDEV_LINK_5000:
+ case TRIGGER_NETDEV_LINK_10000:
case TRIGGER_NETDEV_HALF_DUPLEX:
case TRIGGER_NETDEV_FULL_DUPLEX:
case TRIGGER_NETDEV_TX:
@@ -334,7 +352,10 @@ static ssize_t netdev_led_attr_store(struct device *dev, const char *buf,
if (test_bit(TRIGGER_NETDEV_LINK, &mode) &&
(test_bit(TRIGGER_NETDEV_LINK_10, &mode) ||
test_bit(TRIGGER_NETDEV_LINK_100, &mode) ||
- test_bit(TRIGGER_NETDEV_LINK_1000, &mode)))
+ test_bit(TRIGGER_NETDEV_LINK_1000, &mode) ||
+ test_bit(TRIGGER_NETDEV_LINK_2500, &mode) ||
+ test_bit(TRIGGER_NETDEV_LINK_5000, &mode) ||
+ test_bit(TRIGGER_NETDEV_LINK_10000, &mode)))
return -EINVAL;
cancel_delayed_work_sync(&trigger_data->work);
@@ -364,6 +385,9 @@ DEFINE_NETDEV_TRIGGER(link, TRIGGER_NETDEV_LINK);
DEFINE_NETDEV_TRIGGER(link_10, TRIGGER_NETDEV_LINK_10);
DEFINE_NETDEV_TRIGGER(link_100, TRIGGER_NETDEV_LINK_100);
DEFINE_NETDEV_TRIGGER(link_1000, TRIGGER_NETDEV_LINK_1000);
+DEFINE_NETDEV_TRIGGER(link_2500, TRIGGER_NETDEV_LINK_2500);
+DEFINE_NETDEV_TRIGGER(link_5000, TRIGGER_NETDEV_LINK_5000);
+DEFINE_NETDEV_TRIGGER(link_10000, TRIGGER_NETDEV_LINK_10000);
DEFINE_NETDEV_TRIGGER(half_duplex, TRIGGER_NETDEV_HALF_DUPLEX);
DEFINE_NETDEV_TRIGGER(full_duplex, TRIGGER_NETDEV_FULL_DUPLEX);
DEFINE_NETDEV_TRIGGER(tx, TRIGGER_NETDEV_TX);
@@ -422,6 +446,9 @@ static struct attribute *netdev_trig_attrs[] = {
&dev_attr_link_10.attr,
&dev_attr_link_100.attr,
&dev_attr_link_1000.attr,
+ &dev_attr_link_2500.attr,
+ &dev_attr_link_5000.attr,
+ &dev_attr_link_10000.attr,
&dev_attr_full_duplex.attr,
&dev_attr_half_duplex.attr,
&dev_attr_rx.attr,
@@ -519,6 +546,9 @@ static void netdev_trig_work(struct work_struct *work)
test_bit(TRIGGER_NETDEV_LINK_10, &trigger_data->mode) ||
test_bit(TRIGGER_NETDEV_LINK_100, &trigger_data->mode) ||
test_bit(TRIGGER_NETDEV_LINK_1000, &trigger_data->mode) ||
+ test_bit(TRIGGER_NETDEV_LINK_2500, &trigger_data->mode) ||
+ test_bit(TRIGGER_NETDEV_LINK_5000, &trigger_data->mode) ||
+ test_bit(TRIGGER_NETDEV_LINK_10000, &trigger_data->mode) ||
test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &trigger_data->mode) ||
test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &trigger_data->mode);
interval = jiffies_to_msecs(
diff --git a/include/linux/leds.h b/include/linux/leds.h
index aa16dc2a8230f..1bdf7f5a0d7c0 100644
--- a/include/linux/leds.h
+++ b/include/linux/leds.h
@@ -588,6 +588,9 @@ enum led_trigger_netdev_modes {
TRIGGER_NETDEV_LINK_10,
TRIGGER_NETDEV_LINK_100,
TRIGGER_NETDEV_LINK_1000,
+ TRIGGER_NETDEV_LINK_2500,
+ TRIGGER_NETDEV_LINK_5000,
+ TRIGGER_NETDEV_LINK_10000,
TRIGGER_NETDEV_HALF_DUPLEX,
TRIGGER_NETDEV_FULL_DUPLEX,
TRIGGER_NETDEV_TX,
--
2.43.0
next reply other threads:[~2023-11-26 22:09 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-11-26 22:07 Daniel Golle [this message]
2023-11-27 12:58 ` Andrew Lunn
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=120eddc938b588622020822510e3c19a4d169686.1701035950.git.daniel@makrotopia.org \
--to=daniel@makrotopia.org \
--cc=andrew@lunn.ch \
--cc=ansuelsmth@gmail.com \
--cc=davem@davemloft.net \
--cc=kuba@kernel.org \
--cc=lee@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=lizetao1@huawei.com \
--cc=pavel@ucw.cz \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®