From: Kevin Hao <kexin.hao@windriver.com>
To: Jeff Garzik <jgarzik@redhat.com>,
Jay Cliburn <jacliburn@bellsouth.net>,
Chris Snook <csnook@redhat.com>,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH] net: remove LLTX in atl2 driver
Date: Thu, 25 Sep 2008 08:35:22 +0800 [thread overview]
Message-ID: <1222302922-13200-1-git-send-email-kexin.hao@windriver.com> (raw)
When NETIF_F_LLTX is set, the atlx driver will use a private lock.
But in recent kernels this implementation seems redundant and
can cause problems where AF_PACKET sees things twice. Since
NETIF_F_LLTX is marked as deprecated and shouldn't be used in
new driver, this patch removes NETIF_F_LLTX and adds a mmiowb
before sending packet.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
---
drivers/net/atlx/atl2.c | 24 +-----------------------
drivers/net/atlx/atl2.h | 1 -
2 files changed, 1 insertions(+), 24 deletions(-)
diff --git a/drivers/net/atlx/atl2.c b/drivers/net/atlx/atl2.c
index b2995ac..3df4ee1 100644
--- a/drivers/net/atlx/atl2.c
+++ b/drivers/net/atlx/atl2.c
@@ -116,7 +116,6 @@ static int __devinit atl2_sw_init(struct atl2_adapter *adapter)
hw->max_frame_size = adapter->netdev->mtu;
spin_lock_init(&adapter->stats_lock);
- spin_lock_init(&adapter->tx_lock);
set_bit(__ATL2_DOWN, &adapter->flags);
@@ -749,11 +748,7 @@ static void atl2_down(struct atl2_adapter *adapter)
* reschedule our watchdog timer */
set_bit(__ATL2_DOWN, &adapter->flags);
-#ifdef NETIF_F_LLTX
- netif_stop_queue(netdev);
-#else
netif_tx_disable(netdev);
-#endif
/* reset MAC to disable all RX/TX */
atl2_reset_hw(&adapter->hw);
@@ -829,7 +824,6 @@ static inline int TxdFreeBytes(struct atl2_adapter *adapter)
static int atl2_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
{
struct atl2_adapter *adapter = netdev_priv(netdev);
- unsigned long flags;
struct tx_pkt_header *txph;
u32 offset, copy_len;
int txs_unused;
@@ -845,16 +839,6 @@ static int atl2_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
return NETDEV_TX_OK;
}
-#ifdef NETIF_F_LLTX
- local_irq_save(flags);
- if (!spin_trylock(&adapter->tx_lock)) {
- /* Collision - tell upper layer to requeue */
- local_irq_restore(flags);
- return NETDEV_TX_LOCKED;
- }
-#else
- spin_lock_irqsave(&adapter->tx_lock, flags);
-#endif
txs_unused = TxsFreeUnit(adapter);
txbuf_unused = TxdFreeBytes(adapter);
@@ -862,7 +846,6 @@ static int atl2_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
txs_unused < 1) {
/* not enough resources */
netif_stop_queue(netdev);
- spin_unlock_irqrestore(&adapter->tx_lock, flags);
return NETDEV_TX_BUSY;
}
@@ -908,8 +891,7 @@ static int atl2_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
ATL2_WRITE_REGW(&adapter->hw, REG_MB_TXD_WR_IDX,
(adapter->txd_write_ptr >> 2));
- spin_unlock_irqrestore(&adapter->tx_lock, flags);
-
+ mmiowb();
netdev->trans_start = jiffies;
dev_kfree_skb_any(skb);
return NETDEV_TX_OK;
@@ -1447,10 +1429,6 @@ static int __devinit atl2_probe(struct pci_dev *pdev,
netdev->features |= (NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX);
#endif
-#ifdef NETIF_F_LLTX
- netdev->features |= NETIF_F_LLTX;
-#endif
-
/* Init PHY as early as possible due to power saving issue */
atl2_phy_init(&adapter->hw);
diff --git a/drivers/net/atlx/atl2.h b/drivers/net/atlx/atl2.h
index 6e1f28f..09974df 100644
--- a/drivers/net/atlx/atl2.h
+++ b/drivers/net/atlx/atl2.h
@@ -462,7 +462,6 @@ struct atl2_adapter {
u16 link_duplex;
spinlock_t stats_lock;
- spinlock_t tx_lock;
struct work_struct reset_task;
struct work_struct link_chg_task;
--
1.5.6.2.220.g44701
next reply other threads:[~2008-09-25 0:35 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-09-25 0:35 Kevin Hao [this message]
2008-09-25 20:30 ` Chris Snook
2008-09-25 20:55 ` Jeff Garzik
2008-09-25 22:34 ` Chris Snook
2008-09-25 23:58 ` Jay Cliburn
2008-09-26 1:20 ` Kevin Hao
2008-09-26 1:24 ` Chris Snook
2008-09-26 2:20 ` Kevin Hao
2008-09-26 1:24 ` Jay Cliburn
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1222302922-13200-1-git-send-email-kexin.hao@windriver.com \
--to=kexin.hao@windriver.com \
--cc=csnook@redhat.com \
--cc=jacliburn@bellsouth.net \
--cc=jgarzik@redhat.com \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®