From: Philipp Reisner <philipp.reisner@linbit.com>
To: linux-kernel@vger.kernel.org, Jens Axboe <axboe@kernel.dk>
Cc: drbd-dev@lists.linbit.com
Subject: [PATCH 10/11] drbd: Be consistent in reporting incompatibilities in P_PROTOCOL settings
Date: Fri, 14 Oct 2011 23:57:51 +0200 [thread overview]
Message-ID: <1318629472-11110-11-git-send-email-philipp.reisner@linbit.com> (raw)
In-Reply-To: <1318629472-11110-1-git-send-email-philipp.reisner@linbit.com>
From: Andreas Gruenbacher <agruen@linbit.com>
Refer to the settings by the names which drbdsetup and drbd.conf are using.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
---
drivers/block/drbd/drbd_receiver.c | 14 +++++++-------
1 files changed, 7 insertions(+), 7 deletions(-)
diff --git a/drivers/block/drbd/drbd_receiver.c b/drivers/block/drbd/drbd_receiver.c
index 06bbf0f..aa674bf 100644
--- a/drivers/block/drbd/drbd_receiver.c
+++ b/drivers/block/drbd/drbd_receiver.c
@@ -3093,37 +3093,37 @@ static int receive_protocol(struct drbd_tconn *tconn, struct packet_info *pi)
nc = rcu_dereference(tconn->net_conf);
if (p_proto != nc->wire_protocol) {
- conn_err(tconn, "incompatible communication protocols\n");
+ conn_err(tconn, "incompatible %s settings\n", "protocol");
goto disconnect_rcu_unlock;
}
if (convert_after_sb(p_after_sb_0p) != nc->after_sb_0p) {
- conn_err(tconn, "incompatible after-sb-0pri settings\n");
+ conn_err(tconn, "incompatible %s settings\n", "after-sb-0pri");
goto disconnect_rcu_unlock;
}
if (convert_after_sb(p_after_sb_1p) != nc->after_sb_1p) {
- conn_err(tconn, "incompatible after-sb-1pri settings\n");
+ conn_err(tconn, "incompatible %s settings\n", "after-sb-1pri");
goto disconnect_rcu_unlock;
}
if (convert_after_sb(p_after_sb_2p) != nc->after_sb_2p) {
- conn_err(tconn, "incompatible after-sb-2pri settings\n");
+ conn_err(tconn, "incompatible %s settings\n", "after-sb-2pri");
goto disconnect_rcu_unlock;
}
if (p_discard_my_data && nc->discard_my_data) {
- conn_err(tconn, "both sides have the 'discard_my_data' flag set\n");
+ conn_err(tconn, "incompatible %s settings\n", "discard-my-data");
goto disconnect_rcu_unlock;
}
if (p_two_primaries != nc->two_primaries) {
- conn_err(tconn, "incompatible setting of the two-primaries options\n");
+ conn_err(tconn, "incompatible %s settings\n", "allow-two-primaries");
goto disconnect_rcu_unlock;
}
if (strcmp(integrity_alg, nc->integrity_alg)) {
- conn_err(tconn, "incompatible setting of the data-integrity-alg\n");
+ conn_err(tconn, "incompatible %s settings\n", "data-integrity-alg");
goto disconnect_rcu_unlock;
}
--
1.7.4.1
next prev parent reply other threads:[~2011-10-14 21:57 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-10-14 21:57 [RFC 00/11] drbd: part 20 of adding multiple volume support to drbd Philipp Reisner
2011-10-14 21:57 ` [PATCH 01/11] drbd: Correctly handle resources without volumes Philipp Reisner
2011-10-14 21:57 ` [PATCH 02/11] drbd: report net config even for resources without a single volume Philipp Reisner
2011-10-14 21:57 ` [PATCH 03/11] drbd: Changed some defaults Philipp Reisner
2011-10-14 21:57 ` [PATCH 04/11] drbd: Define scale factors in a single place Philipp Reisner
2011-10-14 21:57 ` [PATCH 05/11] drbd: Fix the maximum accepted minor device number Philipp Reisner
2011-10-14 21:57 ` [PATCH 06/11] drbd: Allow to create devices with a minor number > minor_count Philipp Reisner
2011-10-14 21:57 ` [PATCH 07/11] drbd: Print memory address in hex instead of decimal in error message Philipp Reisner
2011-10-14 21:57 ` [PATCH 08/11] drbd: receive_protocol(): Give variables more easily searchable names Philipp Reisner
2011-10-14 21:57 ` [PATCH 09/11] drbd: receive_protocol(): Make the program flow less confusing Philipp Reisner
2011-10-14 21:57 ` Philipp Reisner [this message]
2011-10-14 21:57 ` [PATCH 11/11] drbd: receive_protocol(): We cannot change our own data-integrity-alg setting here Philipp Reisner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1318629472-11110-11-git-send-email-philipp.reisner@linbit.com \
--to=philipp.reisner@linbit.com \
--cc=axboe@kernel.dk \
--cc=drbd-dev@lists.linbit.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®