From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1757318Ab2ESK3Z (ORCPT ); Sat, 19 May 2012 06:29:25 -0400 Received: from mail.work-microwave.de ([62.245.205.51]:36457 "EHLO work-microwave.de" rhost-flags-OK-OK-OK-FAIL) by vger.kernel.org with ESMTP id S1755345Ab2ESK3Y (ORCPT ); Sat, 19 May 2012 06:29:24 -0400 From: Roland Stigge To: arm@kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org, kevin.wells@nxp.com, srinivas.bakki@nxp.com Cc: Roland Stigge Subject: [PATCH] ARM: LPC32xx: Adjust dts files to gpio dt binding Date: Sat, 19 May 2012 12:28:53 +0200 Message-Id: <1337423333-24356-1-git-send-email-stigge@antcom.de> X-Mailer: git-send-email 1.7.9 X-FEAS-SYSTEM-WL: rst@work-microwave.de, 192.168.11.78 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org The GPIO devicetree binding in 3.5 doesn't register the various LPC32xx GPIO banks via DT subnodes but always all at once, and changes the gpio referencing to 3 cells (bank, gpio, flags). This patch adjusts the DTS files to this binding that was just accepted to the gpio subsystem. Signed-off-by: Roland Stigge --- Applies to branch next/dt of arm-soc.git You can also pull from git://git.antcom.de/linux-2.6.git lpc32xx/dt (where just this single commit is new) arch/arm/boot/dts/lpc32xx.dtsi | 41 ++--------------------------------------- arch/arm/boot/dts/phy3250.dts | 4 ++-- 2 files changed, 4 insertions(+), 41 deletions(-) --- linux-2.6.orig/arch/arm/boot/dts/lpc32xx.dtsi +++ linux-2.6/arch/arm/boot/dts/lpc32xx.dtsi @@ -215,45 +215,8 @@ gpio: gpio@40028000 { compatible = "nxp,lpc3220-gpio"; reg = <0x40028000 0x1000>; - /* create a private address space for enumeration */ - #address-cells = <1>; - #size-cells = <0>; - - gpio_p0: gpio-bank@0 { - gpio-controller; - #gpio-cells = <2>; - reg = <0>; - }; - - gpio_p1: gpio-bank@1 { - gpio-controller; - #gpio-cells = <2>; - reg = <1>; - }; - - gpio_p2: gpio-bank@2 { - gpio-controller; - #gpio-cells = <2>; - reg = <2>; - }; - - gpio_p3: gpio-bank@3 { - gpio-controller; - #gpio-cells = <2>; - reg = <3>; - }; - - gpi_p3: gpio-bank@4 { - gpio-controller; - #gpio-cells = <2>; - reg = <4>; - }; - - gpo_p3: gpio-bank@5 { - gpio-controller; - #gpio-cells = <2>; - reg = <5>; - }; + gpio-controller; + #gpio-cells = <3>; /* bank, pin, flags */ }; watchdog@4003C000 { --- linux-2.6.orig/arch/arm/boot/dts/phy3250.dts +++ linux-2.6/arch/arm/boot/dts/phy3250.dts @@ -131,13 +131,13 @@ compatible = "gpio-leds"; led0 { - gpios = <&gpo_p3 1 1>; /* GPO_P3 1, GPIO 80, active low */ + gpios = <&gpio 5 1 1>; /* GPO_P3 1, GPIO 80, active low */ linux,default-trigger = "heartbeat"; default-state = "off"; }; led1 { - gpios = <&gpo_p3 14 1>; /* GPO_P3 14, GPIO 93, active low */ + gpios = <&gpio 5 14 1>; /* GPO_P3 14, GPIO 93, active low */ linux,default-trigger = "timer"; default-state = "off"; };