From: Saranya Gopal <saranya.gopal@intel.com>
To: lars@metafoo.de, cbou@mail.ru, dwmw2@infradead.org
Cc: linux-kernel@vger.kernel.org, Saranya Gopal <saranya.gopal@intel.com>
Subject: [PATCHv3] bq27x00_battery: Add support for BQ27425 chip
Date: Sat, 30 Jun 2012 22:26:14 +0530 [thread overview]
Message-ID: <1341075374-31704-1-git-send-email-saranya.gopal@intel.com> (raw)
This patch adds support for BQ27425 (TI) chip. This chip is same as
BQ27500 with few registers removed and register address map changed.
The data sheet for this chip is publicly available at
http://www.ti.com/product/bq27425-g1
Changes since v2:
Remove register address definitions of bq27425 and
use register address offset instead.
Add a small helper function to decide if the chip version
is higher than bq27200 to make it less noisy
to add another chip with similar register layout.
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
---
drivers/power/bq27x00_battery.c | 88 +++++++++++++++++++++++++++++++-------
1 files changed, 71 insertions(+), 17 deletions(-)
diff --git a/drivers/power/bq27x00_battery.c b/drivers/power/bq27x00_battery.c
index f5d6d37..ec6ed18 100644
--- a/drivers/power/bq27x00_battery.c
+++ b/drivers/power/bq27x00_battery.c
@@ -22,6 +22,7 @@
* Datasheets:
* http://focus.ti.com/docs/prod/folders/print/bq27000.html
* http://focus.ti.com/docs/prod/folders/print/bq27500.html
+ * http://www.ti.com/product/bq27425-g1
*/
#include <linux/module.h>
@@ -67,6 +68,10 @@
#define BQ27500_FLAG_SOC1 BIT(2) /* State-of-Charge threshold 1 */
#define BQ27500_FLAG_FC BIT(9)
+/* bq27425 register addresses are same as bq27x00 addresses minus 4 */
+#define BQ27425_REG_OFFSET 0x04
+#define BQ27425_REG_SOC 0x1C
+
#define BQ27000_RS 20 /* Resistor sense */
struct bq27x00_device_info;
@@ -74,7 +79,7 @@ struct bq27x00_access_methods {
int (*read)(struct bq27x00_device_info *di, u8 reg, bool single);
};
-enum bq27x00_chip { BQ27000, BQ27500 };
+enum bq27x00_chip { BQ27000, BQ27500, BQ27425};
struct bq27x00_reg_cache {
int temperature;
@@ -125,6 +130,20 @@ static enum power_supply_property bq27x00_battery_props[] = {
POWER_SUPPLY_PROP_ENERGY_NOW,
};
+static enum power_supply_property bq27425_battery_props[] = {
+ POWER_SUPPLY_PROP_STATUS,
+ POWER_SUPPLY_PROP_PRESENT,
+ POWER_SUPPLY_PROP_VOLTAGE_NOW,
+ POWER_SUPPLY_PROP_CURRENT_NOW,
+ POWER_SUPPLY_PROP_CAPACITY,
+ POWER_SUPPLY_PROP_CAPACITY_LEVEL,
+ POWER_SUPPLY_PROP_TEMP,
+ POWER_SUPPLY_PROP_TECHNOLOGY,
+ POWER_SUPPLY_PROP_CHARGE_FULL,
+ POWER_SUPPLY_PROP_CHARGE_NOW,
+ POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
+};
+
static unsigned int poll_interval = 360;
module_param(poll_interval, uint, 0644);
MODULE_PARM_DESC(poll_interval, "battery poll interval in seconds - " \
@@ -137,10 +156,24 @@ MODULE_PARM_DESC(poll_interval, "battery poll interval in seconds - " \
static inline int bq27x00_read(struct bq27x00_device_info *di, u8 reg,
bool single)
{
+ if (di->chip == BQ27425)
+ return di->bus.read(di, reg - BQ27425_REG_OFFSET, single);
return di->bus.read(di, reg, single);
}
/*
+ * Higher versions of the chip like BQ27425 and BQ27500
+ * differ from BQ27000 and BQ27200 in calculation of certain
+ * parameters. Hence we need to check for the chip type.
+ */
+static bool is_chip_version_higher(struct bq27x00_device_info *di)
+{
+ if (di->chip == BQ27425 || di->chip == BQ27500)
+ return true;
+ return false;
+}
+
+/*
* Return the battery Relative State-of-Charge
* Or < 0 if something fails.
*/
@@ -150,6 +183,9 @@ static int bq27x00_battery_read_rsoc(struct bq27x00_device_info *di)
if (di->chip == BQ27500)
rsoc = bq27x00_read(di, BQ27500_REG_SOC, false);
+ else if (di->chip == BQ27425)
+ rsoc = bq27x00_read(di, BQ27425_REG_SOC + BQ27425_REG_OFFSET,
+ false);
else
rsoc = bq27x00_read(di, BQ27000_REG_RSOC, true);
@@ -174,7 +210,7 @@ static int bq27x00_battery_read_charge(struct bq27x00_device_info *di, u8 reg)
return charge;
}
- if (di->chip == BQ27500)
+ if (is_chip_version_higher(di))
charge *= 1000;
else
charge = charge * 3570 / BQ27000_RS;
@@ -208,7 +244,7 @@ static int bq27x00_battery_read_ilmd(struct bq27x00_device_info *di)
{
int ilmd;
- if (di->chip == BQ27500)
+ if (is_chip_version_higher(di))
ilmd = bq27x00_read(di, BQ27500_REG_DCAP, false);
else
ilmd = bq27x00_read(di, BQ27000_REG_ILMD, true);
@@ -218,7 +254,7 @@ static int bq27x00_battery_read_ilmd(struct bq27x00_device_info *di)
return ilmd;
}
- if (di->chip == BQ27500)
+ if (is_chip_version_higher(di))
ilmd *= 1000;
else
ilmd = ilmd * 256 * 3570 / BQ27000_RS;
@@ -262,7 +298,7 @@ static int bq27x00_battery_read_temperature(struct bq27x00_device_info *di)
return temp;
}
- if (di->chip == BQ27500)
+ if (is_chip_version_higher(di))
temp -= 2731;
else
temp = ((temp * 5) - 5463) / 2;
@@ -310,10 +346,12 @@ static void bq27x00_update(struct bq27x00_device_info *di)
{
struct bq27x00_reg_cache cache = {0, };
bool is_bq27500 = di->chip == BQ27500;
+ bool is_bq27425 = di->chip == BQ27425;
cache.flags = bq27x00_read(di, BQ27x00_REG_FLAGS, !is_bq27500);
if (cache.flags >= 0) {
- if (!is_bq27500 && (cache.flags & BQ27000_FLAG_CI)) {
+ if (!is_bq27500 && !is_bq27425
+ && (cache.flags & BQ27000_FLAG_CI)) {
dev_info(di->dev, "battery is not calibrated! ignoring capacity values\n");
cache.capacity = -ENODATA;
cache.energy = -ENODATA;
@@ -323,14 +361,23 @@ static void bq27x00_update(struct bq27x00_device_info *di)
cache.charge_full = -ENODATA;
} else {
cache.capacity = bq27x00_battery_read_rsoc(di);
- cache.energy = bq27x00_battery_read_energy(di);
- cache.time_to_empty = bq27x00_battery_read_time(di, BQ27x00_REG_TTE);
- cache.time_to_empty_avg = bq27x00_battery_read_time(di, BQ27x00_REG_TTECP);
- cache.time_to_full = bq27x00_battery_read_time(di, BQ27x00_REG_TTF);
+ if (!is_bq27425) {
+ cache.energy = bq27x00_battery_read_energy(di);
+ cache.time_to_empty =
+ bq27x00_battery_read_time(di,
+ BQ27x00_REG_TTE);
+ cache.time_to_empty_avg =
+ bq27x00_battery_read_time(di,
+ BQ27x00_REG_TTECP);
+ cache.time_to_full =
+ bq27x00_battery_read_time(di,
+ BQ27x00_REG_TTF);
+ }
cache.charge_full = bq27x00_battery_read_lmd(di);
}
cache.temperature = bq27x00_battery_read_temperature(di);
- cache.cycle_count = bq27x00_battery_read_cyct(di);
+ if (!is_bq27425)
+ cache.cycle_count = bq27x00_battery_read_cyct(di);
/* We only have to read charge design full once */
if (di->charge_design_full <= 0)
@@ -376,7 +423,7 @@ static int bq27x00_battery_current(struct bq27x00_device_info *di,
return curr;
}
- if (di->chip == BQ27500) {
+ if (is_chip_version_higher(di)) {
/* bq27500 returns signed value */
val->intval = (int)((s16)curr) * 1000;
} else {
@@ -397,7 +444,7 @@ static int bq27x00_battery_status(struct bq27x00_device_info *di,
{
int status;
- if (di->chip == BQ27500) {
+ if (is_chip_version_higher(di)) {
if (di->cache.flags & BQ27500_FLAG_FC)
status = POWER_SUPPLY_STATUS_FULL;
else if (di->cache.flags & BQ27500_FLAG_DSC)
@@ -425,7 +472,7 @@ static int bq27x00_battery_capacity_level(struct bq27x00_device_info *di,
{
int level;
- if (di->chip == BQ27500) {
+ if (is_chip_version_higher(di)) {
if (di->cache.flags & BQ27500_FLAG_FC)
level = POWER_SUPPLY_CAPACITY_LEVEL_FULL;
else if (di->cache.flags & BQ27500_FLAG_SOC1)
@@ -570,8 +617,14 @@ static int bq27x00_powersupply_init(struct bq27x00_device_info *di)
int ret;
di->bat.type = POWER_SUPPLY_TYPE_BATTERY;
- di->bat.properties = bq27x00_battery_props;
- di->bat.num_properties = ARRAY_SIZE(bq27x00_battery_props);
+ di->chip = BQ27425;
+ if (di->chip == BQ27425) {
+ di->bat.properties = bq27425_battery_props;
+ di->bat.num_properties = ARRAY_SIZE(bq27425_battery_props);
+ } else {
+ di->bat.properties = bq27x00_battery_props;
+ di->bat.num_properties = ARRAY_SIZE(bq27x00_battery_props);
+ }
di->bat.get_property = bq27x00_battery_get_property;
di->bat.external_power_changed = bq27x00_external_power_changed;
@@ -729,6 +782,7 @@ static int bq27x00_battery_remove(struct i2c_client *client)
static const struct i2c_device_id bq27x00_id[] = {
{ "bq27200", BQ27000 }, /* bq27200 is same as bq27000, but with i2c */
{ "bq27500", BQ27500 },
+ { "bq27425", BQ27425 },
{},
};
MODULE_DEVICE_TABLE(i2c, bq27x00_id);
--
1.7.1
next reply other threads:[~2012-06-30 17:00 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-06-30 16:56 Saranya Gopal [this message]
2012-07-02 16:03 ` Lars-Peter Clausen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1341075374-31704-1-git-send-email-saranya.gopal@intel.com \
--to=saranya.gopal@intel.com \
--cc=cbou@mail.ru \
--cc=dwmw2@infradead.org \
--cc=lars@metafoo.de \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®