From: Andre Przywara <andre.przywara@amd.com>
To: <cpufreq@vger.kernel.org>, "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg@redhat.com>,
Andreas Herrmann <andreas.herrmann3@amd.com>,
Thomas Renninger <trenn@suse.de>, <linux-pm@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
Andre Przywara <andre.przywara@amd.com>
Subject: [PATCH 8/8] Documentation: Add documentation for boost control switch
Date: Thu, 26 Jul 2012 14:28:44 +0200 [thread overview]
Message-ID: <1343305724-2809-9-git-send-email-andre.przywara@amd.com> (raw)
In-Reply-To: <1343305724-2809-1-git-send-email-andre.przywara@amd.com>
The new acpi-cpufreq driver supports a system global control switch
to disable the frequency boosting feature of some (x86) CPUs.
Provide documentation about the rationale and the usage.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
---
Documentation/ABI/testing/sysfs-devices-system-cpu | 12 +++
Documentation/cpu-freq/boost.txt | 94 ++++++++++++++++++++
2 files changed, 106 insertions(+), 0 deletions(-)
create mode 100644 Documentation/cpu-freq/boost.txt
diff --git a/Documentation/ABI/testing/sysfs-devices-system-cpu b/Documentation/ABI/testing/sysfs-devices-system-cpu
index 5dab364..1107a2e 100644
--- a/Documentation/ABI/testing/sysfs-devices-system-cpu
+++ b/Documentation/ABI/testing/sysfs-devices-system-cpu
@@ -176,3 +176,15 @@ Description: Disable L3 cache indices
All AMD processors with L3 caches provide this functionality.
For details, see BKDGs at
http://developer.amd.com/documentation/guides/Pages/default.aspx
+
+
+What: /sys/devices/system/cpu/cpufreq/boost
+Date: August 2012
+Contact: Linux kernel mailing list <linux-kernel@vger.kernel.org>
+Description: Processor frequency boosting control
+
+ This switch controls the boost setting for the whole system.
+ Boosting allows the CPU and the firmware to run at a frequency
+ beyound it's nominal limit.
+ More details can be found in Documentation/cpu-freq/boost.txt
+
diff --git a/Documentation/cpu-freq/boost.txt b/Documentation/cpu-freq/boost.txt
new file mode 100644
index 0000000..0085494
--- /dev/null
+++ b/Documentation/cpu-freq/boost.txt
@@ -0,0 +1,94 @@
+Processor boosting control
+
+ - information for users -
+
+Quick guide for the impatient:
+--------------------
+/sys/devices/system/cpu/cpufreq/boost
+controls the boost setting for the whole system. You can read and write
+that file with either "0" (boosting disabled) or "1" (boosting allowed).
+Reading or writing 1 does not mean that the system is boosting at this
+very moment, but only that the CPU _may_ raise the frequency at it's
+discretion.
+--------------------
+
+Introduction
+-------------
+Some CPUs support a functionality to raise the operating frequency of
+some cores in a multi-core package if certain conditions apply, mostly
+if the whole chip is not fully utilized and below it's intended thermal
+budget. This is done without operating system control by a combination
+of hardware and firmware.
+On Intel CPUs this is called "Turbo Boost", AMD calls it "Turbo-Core",
+in technical documentation "Core performance boost". In Linux we use
+the term "boost" for convenience.
+
+Rationale for disable switch
+----------------------------
+
+Though the idea is to just give better performance without any user
+intervention, sometimes the need arises to disable this functionality.
+Most systems offer a switch in the (BIOS) firmware to disable the
+functionality at all, but a more fine-grained and dynamic control would
+be desirable:
+1. While running benchmarks, reproducible results are important. Since
+ the boosting functionality depends on the load of the whole package,
+ single thread performance can vary. By explicitly disabling the boost
+ functionality at least for the benchmark's run-time the system will run
+ at a fixed frequency and results are reproducible again.
+2. To examine the impact of the boosting functionality it is helpful
+ to do tests with and without boosting.
+3. Boosting means overclocking the processor, though under controlled
+ conditions. By raising the frequency and the voltage the processor
+ will consume more power than without the boosting, which may be
+ undesirable for instance for mobile users. Disabling boosting may
+ save power here, though this depends on the workload.
+
+
+User controlled switch
+----------------------
+
+To allow the user to toggle the boosting functionality, the acpi-cpufreq
+driver exports a sysfs knob to disable it. There is a file:
+/sys/devices/system/cpu/cpufreq/boost
+which can either read "0" (boosting disabled) or "1" (boosting enabled).
+Reading the file is always supported, even if the processor does not
+support boosting. In this case the file will be read-only and always
+reads as "0". Explicitly changing the permissions and writing to that
+file anyway will return EINVAL.
+
+On supported CPUs one can write either a "0" or a "1" into this file.
+This will either disable the boost functionality on all cores in the
+whole system (0) or will allow the hardware to boost at will (1).
+
+Writing a "1" does not explicitly boost the system, but just allows the
+CPU (and the firmware) to boost at their discretion. Some implementations
+take external factors like the chip's temperature into account, so
+boosting once does not necessarily mean that it will occur every time
+even using the exact same software setup.
+
+
+AMD legacy cpb switch
+---------------------
+The AMD powernow-k8 driver used to support a very similar switch to
+disable or enable the "Core Performance Boost" feature of some AMD CPUs.
+This switch was instantiated in each CPU's cpufreq directory
+(/sys/devices/system/cpu[0-9]*/cpufreq) and was called "cpb".
+Though the per CPU existence hints at a more fine grained control, the
+actual implementation only supported a system-global switch semantics,
+which was simply reflected into each CPU's file. Writing a 0 or 1 into it
+would pull the other CPUs to the same state.
+For compatibility reasons this file and its behavior is still supported
+on AMD CPUs, though it is now protected by a config switch
+(X86_ACPI_CPUFREQ_CPB). On Intel CPUs this file will never be created,
+even with the config option set.
+This functionality is considered legacy and will be removed in some future
+kernel version.
+
+More fine grained boosting control
+----------------------------------
+
+Technically it is possible to switch the boosting functionality at least
+on a per package basis, for some CPUs even per core. Currently the driver
+does not support it, but this may be implemented in the future.
+
--
1.7.4.4
next prev parent reply other threads:[~2012-07-26 12:30 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-07-26 12:28 [PATCH 0/8] acpi-cpufreq: Move modern AMD cpufreq support to acpi-cpufreq Andre Przywara
2012-07-26 12:28 ` [PATCH 1/8] acpi-cpufreq: Add support for modern AMD CPUs Andre Przywara
2012-07-26 12:28 ` [PATCH 2/8] acpi-cpufreq: Add quirk to disable _PSD usage on all " Andre Przywara
2012-07-26 12:28 ` [PATCH 3/8] cpufreq: Add compatibility hack to powernow-k8 Andre Przywara
2012-08-22 0:48 ` Thomas Renninger
2012-07-26 12:28 ` [PATCH 4/8] ACPI: Add fixups for AMD P-state figures Andre Przywara
2012-07-26 12:28 ` [PATCH 5/8] acpi-cpufreq: Add support for disabling dynamic overclocking Andre Przywara
2012-08-05 21:26 ` Rafael J. Wysocki
2012-07-26 12:28 ` [PATCH 6/8] acpi-cpufreq: Add compatibility for legacy AMD cpb sysfs knob Andre Przywara
2012-08-05 21:29 ` Rafael J. Wysocki
2012-07-26 12:28 ` [PATCH 7/8] cpufreq: Remove support for hardware P-state chips from powernow-k8 Andre Przywara
2012-08-05 21:33 ` Rafael J. Wysocki
2012-08-20 13:00 ` Andre Przywara
2012-08-20 20:49 ` Rafael J. Wysocki
2012-08-22 1:00 ` Thomas Renninger
2012-08-22 13:39 ` Andre Przywara
2012-08-22 14:34 ` Thomas Renninger
2012-07-26 12:28 ` Andre Przywara [this message]
2012-08-05 21:34 ` [PATCH 8/8] Documentation: Add documentation for boost control switch Rafael J. Wysocki
2012-07-26 14:01 ` [PATCH 0/8] acpi-cpufreq: Move modern AMD cpufreq support to acpi-cpufreq Thomas Renninger
2012-07-26 19:58 ` Rafael J. Wysocki
2012-08-05 21:20 ` Rafael J. Wysocki
2012-08-05 23:39 ` H. Peter Anvin
2012-08-06 8:20 ` Borislav Petkov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1343305724-2809-9-git-send-email-andre.przywara@amd.com \
--to=andre.przywara@amd.com \
--cc=andreas.herrmann3@amd.com \
--cc=cpufreq@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=mjg@redhat.com \
--cc=rjw@sisk.pl \
--cc=trenn@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome