From: Davide Ciminaghi <ciminaghi@gnudd.com>
To: jaswinder.singh@linaro.org, will.deacon@arm.com,
linux@arm.linux.org.uk, tglx@linutronix.de, mingo@redhat.com,
hpa@zytor.com, djbw@fb.com, vinod.koul@intel.com,
grant.likely@secretlab.ca, linus.walleij@linaro.org,
rubini@gnudd.com, wim@iguana.be, cjb@laptop.org,
davidb@codeaurora.org, nico@fluxnic.net, ben-linux@fluff.org,
viresh.linux@gmail.com, rajeev-dlh.kumar@st.com
Cc: linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, giancarlo.asnaghi@st.com
Subject: [PATCH v4 1/7] DMA: PL330: use prefix in reg names to build under x86
Date: Mon, 10 Dec 2012 14:42:30 +0100 [thread overview]
Message-ID: <1355146956-6009-2-git-send-email-ciminaghi@gnudd.com> (raw)
In-Reply-To: <1355146956-6009-1-git-send-email-ciminaghi@gnudd.com>
From: Alessandro Rubini <rubini@gnudd.com>
This driver would not compile if ARM_AMBA is selected under x86,
because "CS" and "DS" are already defined there. But AMBA
is used in the x86 world by a PCI-to-AMBA bridge, to be submitted.
The patch just adds the "PL330_" prefix to all registers,
so it can be built by randomconfig after ARM_AMBA appears within x86.
No other technical changes have been performed.
The patch was build-tested only.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
[Davide Ciminaghi <ciminaghi@gnudd.com>: only registers prefixed]
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
---
The patch is quite big, but what it actually does is just renaming the pl330
registers. What follows is the output of
git diff --word-diff 6c57c3ff~..6c57c3ff
This format should allow better readability for reviewing.
Note that 'index' and '@@' strings at the beginning of lines
have been escaped by adding a leading '#' to avoid errors while actually
applying the patch.
diff --git a/drivers/dma/pl330.c b/drivers/dma/pl330.c
#index f7edb6f..939eec6 100644
--- a/drivers/dma/pl330.c
+++ b/drivers/dma/pl330.c
#@@ -69,7 +69,7 @@ enum pl330_reqtype {
};
/* Register and Bit field Definitions */
#define [-DS-]{+PL330_DS+} 0x0
#define DS_ST_STOP 0x0
#define DS_ST_EXEC 0x1
#define DS_ST_CMISS 0x2
#@@ -83,33 +83,33 @@ enum pl330_reqtype {
#define DS_ST_FLTCMP 0xe
#define DS_ST_FAULT 0xf
#define [-DPC-]{+PL330_DPC+} 0x4
#define [-INTEN-]{+PL330_INTEN+} 0x20
#define [-ES-]{+PL330_ES+} 0x24
#define [-INTSTATUS-]{+PL330_INTSTATUS+} 0x28
#define [-INTCLR-]{+PL330_INTCLR+} 0x2c
#define [-FSM-]{+PL330_FSM+} 0x30
#define [-FSC-]{+PL330_FSC+} 0x34
#define [-FTM-]{+PL330_FTM+} 0x38
#define _FTC 0x40
#define [-FTC(n)-]{+PL330_FTC(n)+} (_FTC + (n)*0x4)
#define _CS 0x100
#define [-CS(n)-]{+PL330_CS(n)+} (_CS + (n)*0x8)
#define CS_CNS (1 << 21)
#define _CPC 0x104
#define [-CPC(n)-]{+PL330_CPC(n)+} (_CPC + (n)*0x8)
#define _SA 0x400
#define [-SA(n)-]{+PL330_SA(n)+} (_SA + (n)*0x20)
#define _DA 0x404
#define [-DA(n)-]{+PL330_DA(n)+} (_DA + (n)*0x20)
#define _CC 0x408
#define [-CC(n)-]{+PL330_CC(n)+} (_CC + (n)*0x20)
#define CC_SRCINC (1 << 0)
#define CC_DSTINC (1 << 14)
#@@ -130,24 +130,24 @@ enum pl330_reqtype {
#define CC_SWAP_SHFT 28
#define _LC0 0x40c
#define [-LC0(n)-]{+PL330_LC0(n)+} (_LC0 + (n)*0x20)
#define _LC1 0x410
#define [-LC1(n)-]{+PL330_LC1(n)+} (_LC1 + (n)*0x20)
#define [-DBGSTATUS-]{+PL330_DBGSTATUS+} 0xd00
#define DBG_BUSY (1 << 0)
#define [-DBGCMD-]{+PL330_DBGCMD+} 0xd04
#define [-DBGINST0-]{+PL330_DBGINST0+} 0xd08
#define [-DBGINST1-]{+PL330_DBGINST1+} 0xd0c
#define [-CR0-]{+PL330_CR0+} 0xe00
#define [-CR1-]{+PL330_CR1+} 0xe04
#define [-CR2-]{+PL330_CR2+} 0xe08
#define [-CR3-]{+PL330_CR3+} 0xe0c
#define [-CR4-]{+PL330_CR4+} 0xe10
#define [-CRD-]{+PL330_CRD+} 0xe14
#define PERIPH_ID 0xfe0
#define PERIPH_REV_SHIFT 20
#@@ -1016,7 +1016,7 @@ static bool _until_dmac_idle(struct pl330_thread *thrd)
do {
/* Until Manager is Idle */
if (!(readl(regs + [-DBGSTATUS)-]{+PL330_DBGSTATUS)+} & DBG_BUSY))
break;
cpu_relax();
#@@ -1039,10 +1039,10 @@ static inline void _execute_DBGINSN(struct pl330_thread *thrd,
val |= (1 << 0);
val |= (thrd->id << 8); /* Channel Number */
}
writel(val, regs + [-DBGINST0);-]{+PL330_DBGINST0);+}
val = *((u32 *)&insn[2]);
writel(val, regs + [-DBGINST1);-]{+PL330_DBGINST1);+}
/* If timed out due to halted state-machine */
if (_until_dmac_idle(thrd)) {
#@@ -1051,7 +1051,7 @@ static inline void _execute_DBGINSN(struct pl330_thread *thrd,
}
/* Get going */
writel(0, regs + [-DBGCMD);-]{+PL330_DBGCMD);+}
}
/*
#@@ -1076,9 +1076,9 @@ static inline u32 _state(struct pl330_thread *thrd)
u32 val;
if (is_manager(thrd))
val = readl(regs + [-DS)-]{+PL330_DS)+} & 0xf;
else
val = readl(regs + [-CS(thrd->id))-]{+PL330_CS(thrd->id))+} & 0xf;
switch (val) {
case DS_ST_STOP:
#@@ -1145,7 +1145,8 @@ static void _stop(struct pl330_thread *thrd)
_emit_KILL(0, insn);
/* Stop generating interrupts for SEV */
writel(readl(regs + [-INTEN)-]{+PL330_INTEN)+} & ~(1 << thrd->ev),
regs + [-INTEN);-]{+PL330_INTEN);+}
_execute_DBGINSN(thrd, insn, is_manager(thrd));
}
#@@ -1184,7 +1185,7 @@ static bool _trigger(struct pl330_thread *thrd)
if (r->cfg)
ns = r->cfg->nonsecure ? 1 : 0;
else if (readl(regs + [-CS(thrd->id))-]{+PL330_CS(thrd->id))+} & CS_CNS)
ns = 1;
else
ns = 0;
#@@ -1200,7 +1201,7 @@ static bool _trigger(struct pl330_thread *thrd)
_emit_GO(0, insn, &go);
/* Set to generate interrupts for SEV */
writel(readl(regs + [-INTEN)-]{+PL330_INTEN)+} | (1 << thrd->ev), regs + [-INTEN);-]{+PL330_INTEN);+}
/* Only manager can execute GO */
_execute_DBGINSN(thrd, insn, true);
#@@ -1575,7 +1576,7 @@ static int pl330_submit_req(void *ch_id, struct pl330_req *r)
ccr = _prepare_ccr(r->cfg);
} else {
ccr = readl(regs + [-CC(thrd->id));-]{+PL330_CC(thrd->id));+}
}
/* If this req doesn't have valid xfer settings */
#@@ -1652,7 +1653,7 @@ static void pl330_dotask(unsigned long data)
_stop(thrd);
if (readl(regs + [-FSC)-]{+PL330_FSC)+} & (1 << thrd->id))
err = PL330_ERR_FAIL;
else
err = PL330_ERR_ABORT;
#@@ -1697,13 +1698,13 @@ static int pl330_update(const struct pl330_info *pi)
spin_lock_irqsave(&pl330->lock, flags);
val = readl(regs + [-FSM)-]{+PL330_FSM)+} & 0x1;
if (val)
pl330->dmac_tbd.reset_mngr = true;
else
pl330->dmac_tbd.reset_mngr = false;
val = readl(regs + [-FSC)-]{+PL330_FSC)+} & ((1 << pi->pcfg.num_chan) - 1);
pl330->dmac_tbd.reset_chan |= val;
if (val) {
int i = 0;
#@@ -1711,8 +1712,8 @@ static int pl330_update(const struct pl330_info *pi)
if (val & (1 << i)) {
dev_info(pi->dev,
"Reset Channel-%d\t CS-%x FTC-%x\n",
i, readl(regs + [-CS(i)),-]{+PL330_CS(i)),+}
readl(regs + [-FTC(i)));-]{+PL330_FTC(i)));+}
_stop(&pl330->channels[i]);
}
i++;
#@@ -1720,7 +1721,7 @@ static int pl330_update(const struct pl330_info *pi)
}
/* Check which event happened i.e, thread notified */
val = readl(regs + [-ES);-]{+PL330_ES);+}
if (pi->pcfg.num_events < 32
&& val & ~((1 << pi->pcfg.num_events) - 1)) {
pl330->dmac_tbd.reset_dmac = true;
#@@ -1732,12 +1733,12 @@ static int pl330_update(const struct pl330_info *pi)
for (ev = 0; ev < pi->pcfg.num_events; ev++) {
if (val & (1 << ev)) { /* Event occurred */
struct pl330_thread *thrd;
u32 inten = readl(regs + [-INTEN);-]{+PL330_INTEN);+}
int active;
/* Clear the event */
if (inten & (1 << ev))
writel(1 << ev, regs + [-INTCLR);-]{+PL330_INTCLR);+}
ret = 1;
#@@ -1944,41 +1945,41 @@ static void read_dmac_config(struct pl330_info *pi)
void __iomem *regs = pi->base;
u32 val;
val = readl(regs + [-CRD)-]{+PL330_CRD)+} >> CRD_DATA_WIDTH_SHIFT;
val &= CRD_DATA_WIDTH_MASK;
pi->pcfg.data_bus_width = 8 * (1 << val);
val = readl(regs + [-CRD)-]{+PL330_CRD)+} >> CRD_DATA_BUFF_SHIFT;
val &= CRD_DATA_BUFF_MASK;
pi->pcfg.data_buf_dep = val + 1;
val = readl(regs + [-CR0)-]{+PL330_CR0)+} >> CR0_NUM_CHANS_SHIFT;
val &= CR0_NUM_CHANS_MASK;
val += 1;
pi->pcfg.num_chan = val;
val = readl(regs + [-CR0);-]{+PL330_CR0);+}
if (val & CR0_PERIPH_REQ_SET) {
val = (val >> CR0_NUM_PERIPH_SHIFT) & CR0_NUM_PERIPH_MASK;
val += 1;
pi->pcfg.num_peri = val;
pi->pcfg.peri_ns = readl(regs + [-CR4);-]{+PL330_CR4);+}
} else {
pi->pcfg.num_peri = 0;
}
val = readl(regs + [-CR0);-]{+PL330_CR0);+}
if (val & CR0_BOOT_MAN_NS)
pi->pcfg.mode |= DMAC_MODE_NS;
else
pi->pcfg.mode &= ~DMAC_MODE_NS;
val = readl(regs + [-CR0)-]{+PL330_CR0)+} >> CR0_NUM_EVENTS_SHIFT;
val &= CR0_NUM_EVENTS_MASK;
val += 1;
pi->pcfg.num_events = val;
pi->pcfg.irq_ns = readl(regs + [-CR3);-]{+PL330_CR3);+}
pi->pcfg.periph_id = get_id(pi, PERIPH_ID);
pi->pcfg.pcell_id = get_id(pi, PCELL_ID);
And here's the actual patch:
drivers/dma/pl330.c | 107 ++++++++++++++++++++++++++-------------------------
1 file changed, 54 insertions(+), 53 deletions(-)
diff --git a/drivers/dma/pl330.c b/drivers/dma/pl330.c
index f7edb6f..939eec6 100644
--- a/drivers/dma/pl330.c
+++ b/drivers/dma/pl330.c
@@ -69,7 +69,7 @@ enum pl330_reqtype {
};
/* Register and Bit field Definitions */
-#define DS 0x0
+#define PL330_DS 0x0
#define DS_ST_STOP 0x0
#define DS_ST_EXEC 0x1
#define DS_ST_CMISS 0x2
@@ -83,33 +83,33 @@ enum pl330_reqtype {
#define DS_ST_FLTCMP 0xe
#define DS_ST_FAULT 0xf
-#define DPC 0x4
-#define INTEN 0x20
-#define ES 0x24
-#define INTSTATUS 0x28
-#define INTCLR 0x2c
-#define FSM 0x30
-#define FSC 0x34
-#define FTM 0x38
+#define PL330_DPC 0x4
+#define PL330_INTEN 0x20
+#define PL330_ES 0x24
+#define PL330_INTSTATUS 0x28
+#define PL330_INTCLR 0x2c
+#define PL330_FSM 0x30
+#define PL330_FSC 0x34
+#define PL330_FTM 0x38
#define _FTC 0x40
-#define FTC(n) (_FTC + (n)*0x4)
+#define PL330_FTC(n) (_FTC + (n)*0x4)
#define _CS 0x100
-#define CS(n) (_CS + (n)*0x8)
+#define PL330_CS(n) (_CS + (n)*0x8)
#define CS_CNS (1 << 21)
#define _CPC 0x104
-#define CPC(n) (_CPC + (n)*0x8)
+#define PL330_CPC(n) (_CPC + (n)*0x8)
#define _SA 0x400
-#define SA(n) (_SA + (n)*0x20)
+#define PL330_SA(n) (_SA + (n)*0x20)
#define _DA 0x404
-#define DA(n) (_DA + (n)*0x20)
+#define PL330_DA(n) (_DA + (n)*0x20)
#define _CC 0x408
-#define CC(n) (_CC + (n)*0x20)
+#define PL330_CC(n) (_CC + (n)*0x20)
#define CC_SRCINC (1 << 0)
#define CC_DSTINC (1 << 14)
@@ -130,24 +130,24 @@ enum pl330_reqtype {
#define CC_SWAP_SHFT 28
#define _LC0 0x40c
-#define LC0(n) (_LC0 + (n)*0x20)
+#define PL330_LC0(n) (_LC0 + (n)*0x20)
#define _LC1 0x410
-#define LC1(n) (_LC1 + (n)*0x20)
+#define PL330_LC1(n) (_LC1 + (n)*0x20)
-#define DBGSTATUS 0xd00
+#define PL330_DBGSTATUS 0xd00
#define DBG_BUSY (1 << 0)
-#define DBGCMD 0xd04
-#define DBGINST0 0xd08
-#define DBGINST1 0xd0c
+#define PL330_DBGCMD 0xd04
+#define PL330_DBGINST0 0xd08
+#define PL330_DBGINST1 0xd0c
-#define CR0 0xe00
-#define CR1 0xe04
-#define CR2 0xe08
-#define CR3 0xe0c
-#define CR4 0xe10
-#define CRD 0xe14
+#define PL330_CR0 0xe00
+#define PL330_CR1 0xe04
+#define PL330_CR2 0xe08
+#define PL330_CR3 0xe0c
+#define PL330_CR4 0xe10
+#define PL330_CRD 0xe14
#define PERIPH_ID 0xfe0
#define PERIPH_REV_SHIFT 20
@@ -1016,7 +1016,7 @@ static bool _until_dmac_idle(struct pl330_thread *thrd)
do {
/* Until Manager is Idle */
- if (!(readl(regs + DBGSTATUS) & DBG_BUSY))
+ if (!(readl(regs + PL330_DBGSTATUS) & DBG_BUSY))
break;
cpu_relax();
@@ -1039,10 +1039,10 @@ static inline void _execute_DBGINSN(struct pl330_thread *thrd,
val |= (1 << 0);
val |= (thrd->id << 8); /* Channel Number */
}
- writel(val, regs + DBGINST0);
+ writel(val, regs + PL330_DBGINST0);
val = *((u32 *)&insn[2]);
- writel(val, regs + DBGINST1);
+ writel(val, regs + PL330_DBGINST1);
/* If timed out due to halted state-machine */
if (_until_dmac_idle(thrd)) {
@@ -1051,7 +1051,7 @@ static inline void _execute_DBGINSN(struct pl330_thread *thrd,
}
/* Get going */
- writel(0, regs + DBGCMD);
+ writel(0, regs + PL330_DBGCMD);
}
/*
@@ -1076,9 +1076,9 @@ static inline u32 _state(struct pl330_thread *thrd)
u32 val;
if (is_manager(thrd))
- val = readl(regs + DS) & 0xf;
+ val = readl(regs + PL330_DS) & 0xf;
else
- val = readl(regs + CS(thrd->id)) & 0xf;
+ val = readl(regs + PL330_CS(thrd->id)) & 0xf;
switch (val) {
case DS_ST_STOP:
@@ -1145,7 +1145,8 @@ static void _stop(struct pl330_thread *thrd)
_emit_KILL(0, insn);
/* Stop generating interrupts for SEV */
- writel(readl(regs + INTEN) & ~(1 << thrd->ev), regs + INTEN);
+ writel(readl(regs + PL330_INTEN) & ~(1 << thrd->ev),
+ regs + PL330_INTEN);
_execute_DBGINSN(thrd, insn, is_manager(thrd));
}
@@ -1184,7 +1185,7 @@ static bool _trigger(struct pl330_thread *thrd)
if (r->cfg)
ns = r->cfg->nonsecure ? 1 : 0;
- else if (readl(regs + CS(thrd->id)) & CS_CNS)
+ else if (readl(regs + PL330_CS(thrd->id)) & CS_CNS)
ns = 1;
else
ns = 0;
@@ -1200,7 +1201,7 @@ static bool _trigger(struct pl330_thread *thrd)
_emit_GO(0, insn, &go);
/* Set to generate interrupts for SEV */
- writel(readl(regs + INTEN) | (1 << thrd->ev), regs + INTEN);
+ writel(readl(regs + PL330_INTEN) | (1 << thrd->ev), regs + PL330_INTEN);
/* Only manager can execute GO */
_execute_DBGINSN(thrd, insn, true);
@@ -1575,7 +1576,7 @@ static int pl330_submit_req(void *ch_id, struct pl330_req *r)
ccr = _prepare_ccr(r->cfg);
} else {
- ccr = readl(regs + CC(thrd->id));
+ ccr = readl(regs + PL330_CC(thrd->id));
}
/* If this req doesn't have valid xfer settings */
@@ -1652,7 +1653,7 @@ static void pl330_dotask(unsigned long data)
_stop(thrd);
- if (readl(regs + FSC) & (1 << thrd->id))
+ if (readl(regs + PL330_FSC) & (1 << thrd->id))
err = PL330_ERR_FAIL;
else
err = PL330_ERR_ABORT;
@@ -1697,13 +1698,13 @@ static int pl330_update(const struct pl330_info *pi)
spin_lock_irqsave(&pl330->lock, flags);
- val = readl(regs + FSM) & 0x1;
+ val = readl(regs + PL330_FSM) & 0x1;
if (val)
pl330->dmac_tbd.reset_mngr = true;
else
pl330->dmac_tbd.reset_mngr = false;
- val = readl(regs + FSC) & ((1 << pi->pcfg.num_chan) - 1);
+ val = readl(regs + PL330_FSC) & ((1 << pi->pcfg.num_chan) - 1);
pl330->dmac_tbd.reset_chan |= val;
if (val) {
int i = 0;
@@ -1711,8 +1712,8 @@ static int pl330_update(const struct pl330_info *pi)
if (val & (1 << i)) {
dev_info(pi->dev,
"Reset Channel-%d\t CS-%x FTC-%x\n",
- i, readl(regs + CS(i)),
- readl(regs + FTC(i)));
+ i, readl(regs + PL330_CS(i)),
+ readl(regs + PL330_FTC(i)));
_stop(&pl330->channels[i]);
}
i++;
@@ -1720,7 +1721,7 @@ static int pl330_update(const struct pl330_info *pi)
}
/* Check which event happened i.e, thread notified */
- val = readl(regs + ES);
+ val = readl(regs + PL330_ES);
if (pi->pcfg.num_events < 32
&& val & ~((1 << pi->pcfg.num_events) - 1)) {
pl330->dmac_tbd.reset_dmac = true;
@@ -1732,12 +1733,12 @@ static int pl330_update(const struct pl330_info *pi)
for (ev = 0; ev < pi->pcfg.num_events; ev++) {
if (val & (1 << ev)) { /* Event occurred */
struct pl330_thread *thrd;
- u32 inten = readl(regs + INTEN);
+ u32 inten = readl(regs + PL330_INTEN);
int active;
/* Clear the event */
if (inten & (1 << ev))
- writel(1 << ev, regs + INTCLR);
+ writel(1 << ev, regs + PL330_INTCLR);
ret = 1;
@@ -1944,41 +1945,41 @@ static void read_dmac_config(struct pl330_info *pi)
void __iomem *regs = pi->base;
u32 val;
- val = readl(regs + CRD) >> CRD_DATA_WIDTH_SHIFT;
+ val = readl(regs + PL330_CRD) >> CRD_DATA_WIDTH_SHIFT;
val &= CRD_DATA_WIDTH_MASK;
pi->pcfg.data_bus_width = 8 * (1 << val);
- val = readl(regs + CRD) >> CRD_DATA_BUFF_SHIFT;
+ val = readl(regs + PL330_CRD) >> CRD_DATA_BUFF_SHIFT;
val &= CRD_DATA_BUFF_MASK;
pi->pcfg.data_buf_dep = val + 1;
- val = readl(regs + CR0) >> CR0_NUM_CHANS_SHIFT;
+ val = readl(regs + PL330_CR0) >> CR0_NUM_CHANS_SHIFT;
val &= CR0_NUM_CHANS_MASK;
val += 1;
pi->pcfg.num_chan = val;
- val = readl(regs + CR0);
+ val = readl(regs + PL330_CR0);
if (val & CR0_PERIPH_REQ_SET) {
val = (val >> CR0_NUM_PERIPH_SHIFT) & CR0_NUM_PERIPH_MASK;
val += 1;
pi->pcfg.num_peri = val;
- pi->pcfg.peri_ns = readl(regs + CR4);
+ pi->pcfg.peri_ns = readl(regs + PL330_CR4);
} else {
pi->pcfg.num_peri = 0;
}
- val = readl(regs + CR0);
+ val = readl(regs + PL330_CR0);
if (val & CR0_BOOT_MAN_NS)
pi->pcfg.mode |= DMAC_MODE_NS;
else
pi->pcfg.mode &= ~DMAC_MODE_NS;
- val = readl(regs + CR0) >> CR0_NUM_EVENTS_SHIFT;
+ val = readl(regs + PL330_CR0) >> CR0_NUM_EVENTS_SHIFT;
val &= CR0_NUM_EVENTS_MASK;
val += 1;
pi->pcfg.num_events = val;
- pi->pcfg.irq_ns = readl(regs + CR3);
+ pi->pcfg.irq_ns = readl(regs + PL330_CR3);
pi->pcfg.periph_id = get_id(pi, PERIPH_ID);
pi->pcfg.pcell_id = get_id(pi, PCELL_ID);
--
1.7.10.4
next prev parent reply other threads:[~2012-12-10 13:44 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-12-10 13:42 [PATCH v4 0/7] enable support for AMBA drivers " Davide Ciminaghi
2012-12-10 13:42 ` Davide Ciminaghi [this message]
2012-12-11 4:25 ` [PATCH v4 1/7] DMA: PL330: use prefix in reg names to build " Jassi Brar
2012-12-10 13:42 ` [PATCH v4 2/7] pl080.h: moved from arm/include/asm/hardware to include/linux/amba/ Davide Ciminaghi
2012-12-10 21:44 ` Linus Walleij
2012-12-10 22:25 ` Davide Ciminaghi
2013-01-13 13:25 ` Vinod Koul
2012-12-10 13:42 ` [PATCH v4 3/7] watchdog: sp805_wdt depends on ARM Davide Ciminaghi
2012-12-12 21:21 ` Wim Van Sebroeck
2012-12-12 22:20 ` Grant Likely
2012-12-10 13:42 ` [PATCH v4 4/7] mmci: replace readsl/writesl with ioread32_rep/iowrite32_rep Davide Ciminaghi
2012-12-10 13:42 ` [PATCH v4 5/7] mmc: use the new <linux/sizes.h> Davide Ciminaghi
2012-12-10 13:42 ` [PATCH v4 6/7] drivers/amba: add support for a PCI bridge Davide Ciminaghi
2012-12-10 13:42 ` [PATCH v4 7/7] x86: add CONFIG_ARM_AMBA, selected by STA2X11 Davide Ciminaghi
2012-12-13 0:48 ` H. Peter Anvin
2012-12-10 22:15 ` [PATCH v4 0/7] enable support for AMBA drivers under x86 David Brown
2012-12-13 0:37 ` H. Peter Anvin
2012-12-13 1:10 ` Grant Likely
2012-12-13 1:16 ` H. Peter Anvin
2012-12-13 2:02 ` H. Peter Anvin
2012-12-13 2:16 ` H. Peter Anvin
2012-12-13 18:14 ` Alessandro Rubini
2013-05-05 12:36 ` Borislav Petkov
2013-05-05 20:24 ` Alessandro Rubini
2013-05-05 20:39 ` Borislav Petkov
2013-05-06 9:41 ` Ingo Molnar
2013-05-06 10:11 ` Borislav Petkov
2013-05-06 9:54 ` Alessandro Rubini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1355146956-6009-2-git-send-email-ciminaghi@gnudd.com \
--to=ciminaghi@gnudd.com \
--cc=ben-linux@fluff.org \
--cc=cjb@laptop.org \
--cc=davidb@codeaurora.org \
--cc=djbw@fb.com \
--cc=giancarlo.asnaghi@st.com \
--cc=grant.likely@secretlab.ca \
--cc=hpa@zytor.com \
--cc=jaswinder.singh@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
--cc=mingo@redhat.com \
--cc=nico@fluxnic.net \
--cc=rajeev-dlh.kumar@st.com \
--cc=rubini@gnudd.com \
--cc=tglx@linutronix.de \
--cc=vinod.koul@intel.com \
--cc=viresh.linux@gmail.com \
--cc=will.deacon@arm.com \
--cc=wim@iguana.be \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®