From: Mark Brown <broonie@opensource.wolfsonmicro.com>
To: Samuel Ortiz <sameo@linux.intel.com>
Cc: linux-kernel@vger.kernel.org,
patches@opensource.wolfsonmicro.com,
Mark Brown <broonie@opensource.wolfsonmicro.com>
Subject: [PATCH 07/15] mfd: wm5102: Update patch for latest evaluation
Date: Mon, 1 Apr 2013 18:28:04 +0100 [thread overview]
Message-ID: <1364837292-30191-7-git-send-email-broonie@opensource.wolfsonmicro.com> (raw)
In-Reply-To: <1364837292-30191-1-git-send-email-broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
---
drivers/mfd/wm5102-tables.c | 15 ++++++++++-----
1 file changed, 10 insertions(+), 5 deletions(-)
diff --git a/drivers/mfd/wm5102-tables.c b/drivers/mfd/wm5102-tables.c
index a433f58..909e043 100644
--- a/drivers/mfd/wm5102-tables.c
+++ b/drivers/mfd/wm5102-tables.c
@@ -57,15 +57,20 @@ static const struct reg_default wm5102_reva_patch[] = {
};
static const struct reg_default wm5102_revb_patch[] = {
+ { 0x19, 0x0001 },
{ 0x80, 0x0003 },
{ 0x081, 0xE022 },
- { 0x410, 0x4080 },
- { 0x418, 0x4080 },
- { 0x420, 0x4080 },
- { 0x428, 0xC000 },
+ { 0x410, 0x6080 },
+ { 0x418, 0xa080 },
+ { 0x420, 0xa080 },
+ { 0x428, 0xe000 },
+ { 0x443, 0xDC1A },
{ 0x4B0, 0x0066 },
{ 0x458, 0x000b },
{ 0x212, 0x0000 },
+ { 0x171, 0x0000 },
+ { 0x35E, 0x000C },
+ { 0x2D4, 0x0000 },
{ 0x80, 0x0000 },
};
@@ -282,7 +287,7 @@ static const struct reg_default wm5102_reg_default[] = {
{ 0x00000155, 0x0000 }, /* R341 - Rate Estimator 4 */
{ 0x00000156, 0x0000 }, /* R342 - Rate Estimator 5 */
{ 0x00000161, 0x0000 }, /* R353 - Dynamic Frequency Scaling 1 */
- { 0x00000171, 0x0002 }, /* R369 - FLL1 Control 1 */
+ { 0x00000171, 0x0000 }, /* R369 - FLL1 Control 1 */
{ 0x00000172, 0x0008 }, /* R370 - FLL1 Control 2 */
{ 0x00000173, 0x0018 }, /* R371 - FLL1 Control 3 */
{ 0x00000174, 0x007D }, /* R372 - FLL1 Control 4 */
--
1.7.10.4
next prev parent reply other threads:[~2013-04-01 17:30 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-04-01 17:27 [PATCH 0/15] arizona updates for v3.10 Mark Brown
2013-04-01 17:27 ` [PATCH 01/15] mfd: arizona: Disable all wake sources by default Mark Brown
2013-04-01 17:27 ` [PATCH 02/15] mfd: arizona: Clarify error message for failed primary IRQ request Mark Brown
2013-04-01 17:28 ` [PATCH 03/15] mfd: arizona: Basic support for edge triggered IRQs Mark Brown
2013-04-01 17:28 ` [PATCH 04/15] mfd: arizona: Allow GPIO to be specified for IRQ line Mark Brown
2013-04-01 17:28 ` [PATCH 05/15] mfd: arizona: Try to use interrupt flags from interrupt controller Mark Brown
2013-04-01 17:28 ` [PATCH 06/15] mfd: arizona: Support configuring MICBIASes into bypass mode Mark Brown
2013-04-01 17:28 ` Mark Brown [this message]
2013-04-01 17:28 ` [PATCH 08/15] mfd: arizona: Fully support the use of MCLK1 as the 32kHz clock source Mark Brown
2013-04-01 17:28 ` [PATCH 09/15] mfd: arizona: Unconditionally enable 32kHz clock Mark Brown
2013-04-01 17:28 ` [PATCH 10/15] mfd: wm5102: Only use the lowest three bits of device revision Mark Brown
2013-04-01 17:28 ` [PATCH 11/15] mfd: wm5102: Manually apply register patch Mark Brown
2013-04-01 17:28 ` [PATCH 12/15] mfd: arizona: Factor out register polling Mark Brown
2013-04-01 17:28 ` [PATCH 13/15] mfd: arizona: Add a hardware patch mechanism Mark Brown
2013-04-01 17:28 ` [PATCH 14/15] mfd: wm5102: Deactivate standard boot sequence Mark Brown
2013-04-01 17:28 ` [PATCH 15/15] mfd: wm5102: Update defaults to match patch Mark Brown
2013-04-03 18:04 ` [PATCH 0/15] arizona updates for v3.10 Mark Brown
2013-04-03 18:05 ` [PATCH 1/3] mfd: arizona: Hold device in reset while ramping supplies Mark Brown
2013-04-03 18:05 ` [PATCH 2/3] mfd: arizona: Wait for internal clocks to startup after reset Mark Brown
2013-04-03 18:05 ` [PATCH 3/3] mfd: wm5102: Don't wait for boot when boot sequencer is disabled Mark Brown
2013-04-08 9:25 ` [PATCH 0/15] arizona updates for v3.10 Samuel Ortiz
2013-04-08 9:38 ` Samuel Ortiz
2013-04-08 10:04 ` Mark Brown
2013-04-08 10:19 ` Mark Brown
2013-04-08 14:31 ` Samuel Ortiz
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1364837292-30191-7-git-send-email-broonie@opensource.wolfsonmicro.com \
--to=broonie@opensource.wolfsonmicro.com \
--cc=linux-kernel@vger.kernel.org \
--cc=patches@opensource.wolfsonmicro.com \
--cc=sameo@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome