[PATCH 4/5] binding: Add device tree bindings for freescale AIC and AD phy

[<akhil.goyal@freescale.com>]

From: Akhil Goyal <akhil.goyal@freescale.com>

For platforms like BSC9131 and BSC9132, a Radio framework for supporting
various network modes comprise of an Antenna interface controller driver
and a phy driver(AD9361 in this case).
A combination of AIC lane and AD phy is called a rf device which can be used
to operate on a particular network mode.

This patch explain various device tree properties required for AIC and
AD9361 drivers.

Signed-off-by: Akhil Goyal <akhil.goyal@freescale.com>
---
 .../devicetree/bindings/rf/ad9361-phy.txt          |   53 ++++++++++++++++++++
 Documentation/devicetree/bindings/rf/fsl-aic.txt   |   47 +++++++++++++++++
 2 files changed, 100 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/rf/ad9361-phy.txt
 create mode 100644 Documentation/devicetree/bindings/rf/fsl-aic.txt

diff --git a/Documentation/devicetree/bindings/rf/ad9361-phy.txt b/Documentation/devicetree/bindings/rf/ad9361-phy.txt
new file mode 100644
index 0000000..9dbf736
--- /dev/null
+++ b/Documentation/devicetree/bindings/rf/ad9361-phy.txt
@@ -0,0 +1,53 @@
+* AD9361-phy
+
+Required Properties:
+- compatible : should be "adi,ad9361"
+- reg : chipselect of the spi controller
+- spi-max-frequency :  maximum spi bus frequency for this device (Hz).
+- spi-cpha : (optional) Empty property indicating device requires
+		shifted clock phase (CPHA) mode
+- fsl,ad9361-gpios : Specifies GPIOs being used for AD9361
+		This sequence shall be maintained.
+		Here, <&gpio1 2 1> denotes reset gpio
+		<&gpio0 18 1> denotes pa_en gpio
+		<&gpio0 17 1> denotes lna_en gpio
+- fsl,ad9361-band-grpX : denotes group of LTE/WCDMA bands available for a
+  particular combination of values of pa_en and lna_en gpios.
+  where X can be 1,2,3,4
+	- fsl,ad9361-bands : denotes LTE/WCDMA band numbers for normal DL/UL
+	- fsl,ad9361-sniff-bands : denotes LTE/WCDMA band numbers for sniffing
+	- fsl,ad9361-lna : if present in the node then, lna_en gpio is enabled
+	- fsl,ad9361-pa : if present in the node then, pa_en gpio is enabled
+
+For Example:
+
+rfphy0: ad9361-phy@0{
+	compatible = "adi,ad9361";
+	reg = <0>;
+	spi-max-frequency = <20000000>;
+	spi-cpha;
+	fsl,ad9361-gpios = <&gpio1 2 1 &gpio0 18 1 &gpio0 17 1>;
+	fsl,ad9361-band-grp1 {
+		fsl,ad9361-bands = <1 7>;
+		fsl,ad9361-sniff-bands = <>;
+	};
+	fsl,ad9361-band-grp2 {
+		fsl,ad9361-lna;
+		fsl,ad9361-bands= <41>;
+		fsl,ad9361-sniff-bands = <13>;
+	};
+	fsl,ad9361-band-grp3 {
+		fsl,ad9361-pa;
+		fsl,ad9361-bands = <>;
+		fsl,ad9361-sniff-bands = <1 7>;
+	};
+	fsl,ad9361-band-grp4 {
+		fsl,ad9361-pa;
+		fsl,ad9361-lna;
+		fsl,ad9361-bands = <13 40>;
+		fsl,ad9361-sniff-bands = <>;
+	};
+};
+
+
+
diff --git a/Documentation/devicetree/bindings/rf/fsl-aic.txt b/Documentation/devicetree/bindings/rf/fsl-aic.txt
new file mode 100644
index 0000000..4f54a92
--- /dev/null
+++ b/Documentation/devicetree/bindings/rf/fsl-aic.txt
@@ -0,0 +1,47 @@
+Freescale Antenna Interface Controller
+
+AIC is the antenna interface controller found in bsc913x
+family of SOCs. It supports NCDMA, WCDMA-FDD, LTE-FDD, LTE-TDD
+and GSM-SNIFF network modes. AIC has multiple lanes on which RFICs
+can be connected. And AIC supports 4 RFICs working simultaneously.
+
+Required Properties:
+- #address-cells : should be 1
+- #size-cells : should be 1
+- compatible : should be fsl,bsc9131-aic or fsl,bsc9132-aic or both
+- reg : offset and length of common register set of AIC
+- interrupts : For AIC, first is capture complete interrupt
+		second is dsp general interrupt
+aic node can have multiple sub nodes of aiclanes for each lane.
+- aiclane : Required Properties
+	- reg : offset and length of common register set of AIC lane
+	- lane_id : it can be 0, 1, 2, 3, 4, 5
+	- interrupts : lane specific TTI interrupt line
+
+For Example:
+
+aic@50000 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "fsl,bsc9131-aic", "fsl,bsc9132-aic";
+	reg = <0x50000 0x200>;
+	interrupts = <49 2 0 0 53 2 0 0>;
+	lane0: aiclane@200 {
+		reg = <0x200 0x200>;
+		lane_id = <0>;
+		interrupts = <45 2 0 0>;
+	};
+
+	lane1: aiclane@400 {
+		reg = <0x400 0x200>;
+		lane_id = <1>;
+		interrupts = <46 2 0 0>;
+	};
+
+	lane2: aiclane@600 {
+		reg = <0x600 0x200>;
+		lane_id = <2>;
+		interrupts = <47 2 0 0>;
+	};
+};
+
-- 
1.6.3.1