From: Yijing Wang <wangyijing@huawei.com>
To: "David S. Miller" <davem@davemloft.net>
Cc: <linux-kernel@vger.kernel.org>, Hanjun Guo <guohanjun@huawei.com>,
Yijing Wang <wangyijing@huawei.com>, <netdev@vger.kernel.org>
Subject: [PATCH 2/6] net/trivial: replace numeric with standard PM state macros
Date: Thu, 27 Jun 2013 20:53:42 +0800 [thread overview]
Message-ID: <1372337622-26076-1-git-send-email-wangyijing@huawei.com> (raw)
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
---
drivers/net/ethernet/8390/ne2k-pci.c | 2 +-
drivers/net/ethernet/emulex/benet/be_main.c | 4 ++--
drivers/net/ethernet/intel/e100.c | 4 ++--
drivers/net/ethernet/myricom/myri10ge/myri10ge.c | 2 +-
drivers/net/ethernet/realtek/8139cp.c | 2 +-
drivers/net/ethernet/ti/tlan.c | 2 +-
drivers/net/ethernet/via/via-velocity.c | 2 +-
drivers/net/wireless/orinoco/orinoco_pci.h | 2 +-
8 files changed, 10 insertions(+), 10 deletions(-)
diff --git a/drivers/net/ethernet/8390/ne2k-pci.c b/drivers/net/ethernet/8390/ne2k-pci.c
index 587a885..9220108 100644
--- a/drivers/net/ethernet/8390/ne2k-pci.c
+++ b/drivers/net/ethernet/8390/ne2k-pci.c
@@ -676,7 +676,7 @@ static int ne2k_pci_resume (struct pci_dev *pdev)
struct net_device *dev = pci_get_drvdata (pdev);
int rc;
- pci_set_power_state(pdev, 0);
+ pci_set_power_state(pdev, PCI_D0);
pci_restore_state(pdev);
rc = pci_enable_device(pdev);
diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c
index a0b4be5..f4994ae 100644
--- a/drivers/net/ethernet/emulex/benet/be_main.c
+++ b/drivers/net/ethernet/emulex/benet/be_main.c
@@ -4390,7 +4390,7 @@ static int be_resume(struct pci_dev *pdev)
if (status)
return status;
- pci_set_power_state(pdev, 0);
+ pci_set_power_state(pdev, PCI_D0);
pci_restore_state(pdev);
/* tell fw we're ready to fire cmds */
@@ -4486,7 +4486,7 @@ static pci_ers_result_t be_eeh_reset(struct pci_dev *pdev)
return PCI_ERS_RESULT_DISCONNECT;
pci_set_master(pdev);
- pci_set_power_state(pdev, 0);
+ pci_set_power_state(pdev, PCI_D0);
pci_restore_state(pdev);
/* Check if card is ok and fw is ready */
diff --git a/drivers/net/ethernet/intel/e100.c b/drivers/net/ethernet/intel/e100.c
index d2bea3f..5115ae7 100644
--- a/drivers/net/ethernet/intel/e100.c
+++ b/drivers/net/ethernet/intel/e100.c
@@ -3069,7 +3069,7 @@ static int e100_resume(struct pci_dev *pdev)
pci_set_power_state(pdev, PCI_D0);
pci_restore_state(pdev);
/* ack any pending wake events, disable PME */
- pci_enable_wake(pdev, 0, 0);
+ pci_enable_wake(pdev, PCI_D0, 0);
/* disable reverse auto-negotiation */
if (nic->phy == phy_82552_v) {
@@ -3160,7 +3160,7 @@ static void e100_io_resume(struct pci_dev *pdev)
struct nic *nic = netdev_priv(netdev);
/* ack any pending wake events, disable PME */
- pci_enable_wake(pdev, 0, 0);
+ pci_enable_wake(pdev, PCI_D0, 0);
netif_device_attach(netdev);
if (netif_running(netdev)) {
diff --git a/drivers/net/ethernet/myricom/myri10ge/myri10ge.c b/drivers/net/ethernet/myricom/myri10ge/myri10ge.c
index 7be9788..967bae8 100644
--- a/drivers/net/ethernet/myricom/myri10ge/myri10ge.c
+++ b/drivers/net/ethernet/myricom/myri10ge/myri10ge.c
@@ -3299,7 +3299,7 @@ static int myri10ge_resume(struct pci_dev *pdev)
if (mgp == NULL)
return -EINVAL;
netdev = mgp->dev;
- pci_set_power_state(pdev, 0); /* zeros conf space as a side effect */
+ pci_set_power_state(pdev, PCI_D0); /* zeros conf space as a side effect */
msleep(5); /* give card time to respond */
pci_read_config_word(mgp->pdev, PCI_VENDOR_ID, &vendor);
if (vendor == 0xffff) {
diff --git a/drivers/net/ethernet/realtek/8139cp.c b/drivers/net/ethernet/realtek/8139cp.c
index 0352345..e6acb9f 100644
--- a/drivers/net/ethernet/realtek/8139cp.c
+++ b/drivers/net/ethernet/realtek/8139cp.c
@@ -1817,7 +1817,7 @@ static int cp_set_eeprom(struct net_device *dev,
/* Put the board into D3cold state and wait for WakeUp signal */
static void cp_set_d3_state (struct cp_private *cp)
{
- pci_enable_wake (cp->pdev, 0, 1); /* Enable PME# generation */
+ pci_enable_wake(cp->pdev, PCI_D0, 1); /* Enable PME# generation */
pci_set_power_state (cp->pdev, PCI_D3hot);
}
diff --git a/drivers/net/ethernet/ti/tlan.c b/drivers/net/ethernet/ti/tlan.c
index 60c400f..c80b1d5 100644
--- a/drivers/net/ethernet/ti/tlan.c
+++ b/drivers/net/ethernet/ti/tlan.c
@@ -372,7 +372,7 @@ static int tlan_resume(struct pci_dev *pdev)
pci_set_power_state(pdev, PCI_D0);
pci_restore_state(pdev);
- pci_enable_wake(pdev, 0, 0);
+ pci_enable_wake(pdev, PCI_D0, 0);
netif_device_attach(dev);
if (netif_running(dev))
diff --git a/drivers/net/ethernet/via/via-velocity.c b/drivers/net/ethernet/via/via-velocity.c
index fb62489..f5d7c3f 100644
--- a/drivers/net/ethernet/via/via-velocity.c
+++ b/drivers/net/ethernet/via/via-velocity.c
@@ -3082,7 +3082,7 @@ static int velocity_resume(struct pci_dev *pdev)
return 0;
pci_set_power_state(pdev, PCI_D0);
- pci_enable_wake(pdev, 0, 0);
+ pci_enable_wake(pdev, PCI_D0, 0);
pci_restore_state(pdev);
mac_wol_reset(vptr->mac_regs);
diff --git a/drivers/net/wireless/orinoco/orinoco_pci.h b/drivers/net/wireless/orinoco/orinoco_pci.h
index ea7231a..43f5b9f 100644
--- a/drivers/net/wireless/orinoco/orinoco_pci.h
+++ b/drivers/net/wireless/orinoco/orinoco_pci.h
@@ -38,7 +38,7 @@ static int orinoco_pci_resume(struct pci_dev *pdev)
struct net_device *dev = priv->ndev;
int err;
- pci_set_power_state(pdev, 0);
+ pci_set_power_state(pdev, PCI_D0);
err = pci_enable_device(pdev);
if (err) {
printk(KERN_ERR "%s: pci_enable_device failed on resume\n",
--
1.7.1
next reply other threads:[~2013-06-27 12:54 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-06-27 12:53 Yijing Wang [this message]
2013-06-29 5:12 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1372337622-26076-1-git-send-email-wangyijing@huawei.com \
--to=wangyijing@huawei.com \
--cc=davem@davemloft.net \
--cc=guohanjun@huawei.com \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®