From: Lee Jones <lee.jones@linaro.org>
To: linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, dwmw2@infradead.org,
linux-mtd@lists.infradead.org, angus.clark@st.com
Cc: linus.walleij@linaro.org, Lee Jones <lee.jones@linaro.org>
Subject: [PATCH 20/23] mtd: st_spi_fsm: Provide a method to put the chip into 32bit addressing mode
Date: Fri, 22 Nov 2013 16:22:57 +0000 [thread overview]
Message-ID: <1385137380-28968-21-git-send-email-lee.jones@linaro.org> (raw)
In-Reply-To: <1385137380-28968-1-git-send-email-lee.jones@linaro.org>
Most Serial Flash chips support 24bit addressing as a default but more
recent incarnations can support 32bit. Based on information provided
though platform specific data and capabilities we can determine whether
or not our current chip can. This patch provides a means to setup the
FSM message sequence to put the chip into 32bit mode.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
drivers/mtd/devices/st_spi_fsm.c | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/drivers/mtd/devices/st_spi_fsm.c b/drivers/mtd/devices/st_spi_fsm.c
index 9a66c99..b99b4c1 100644
--- a/drivers/mtd/devices/st_spi_fsm.c
+++ b/drivers/mtd/devices/st_spi_fsm.c
@@ -28,6 +28,8 @@
#include "st_spi_fsm.h"
#include "serial_flash_cmds.h"
+static struct stfsm_seq stfsm_seq_en_32bit_addr;/* Dynamically populated */
+
static struct stfsm_seq stfsm_seq_read_jedec = {
.data_size = TRANSFER_SIZE(8),
.seq_opc[0] = (SEQ_OPC_PADS_1 |
@@ -128,6 +130,23 @@ static void stfsm_wait_seq(struct stfsm *fsm)
dev_err(fsm->dev, "timeout on sequence completion\n");
}
+static int stfsm_enter_32bit_addr(struct stfsm *fsm, int enter)
+{
+ struct stfsm_seq *seq = &stfsm_seq_en_32bit_addr;
+ uint32_t cmd = enter ? FLASH_CMD_EN4B_ADDR : FLASH_CMD_EX4B_ADDR;
+
+ seq->seq_opc[0] = (SEQ_OPC_PADS_1 |
+ SEQ_OPC_CYCLES(8) |
+ SEQ_OPC_OPCODE(cmd) |
+ SEQ_OPC_CSDEASSERT);
+
+ stfsm_load_seq(fsm, seq);
+
+ stfsm_wait_seq(fsm);
+
+ return 0;
+}
+
/*
* SoC reset on 'boot-from-spi' systems
*
--
1.8.1.2
next prev parent reply other threads:[~2013-11-22 16:24 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-11-22 16:22 [PATCH 00/23] mtd: st_spi_fsm: Add new device Lee Jones
2013-11-22 16:22 ` [PATCH 01/23] mtd: st_spi_fsm: Allocate resources and register with MTD framework Lee Jones
2013-11-22 16:22 ` [PATCH 02/23] mtd: st_spi_fsm: Supply all register address and bit logic defines Lee Jones
2013-11-22 16:22 ` [PATCH 03/23] mtd: st_spi_fsm: Initialise and configure the FSM for normal working conditions Lee Jones
2013-11-22 16:22 ` [PATCH 04/23] mtd: st_spi_fsm: Supply framework for device requests Lee Jones
2013-11-22 16:22 ` [PATCH 05/23] mtd: st_spi_fsm: Supply a method to read from the FSM's FIFO Lee Jones
2013-11-22 16:22 ` [PATCH 06/23] mtd: st_spi_fsm: Supply defines for the possible flash command opcodes Lee Jones
2013-11-22 16:22 ` [PATCH 07/23] mtd: st_spi_fsm: Add support for JEDEC ID extraction Lee Jones
2013-11-22 16:22 ` [PATCH 08/23] mtd: devices: Provide header for shared OPCODEs and SFDP commands Lee Jones
2013-11-22 16:22 ` [PATCH 09/23] mtd: st_spi_fsm: Provide device look-up table Lee Jones
2013-11-22 16:22 ` [PATCH 10/23] mtd: st_spi_fsm: Dynamically setup flash device based on JEDEC ID Lee Jones
2013-11-22 16:22 ` [PATCH 11/23] ARM: STi: Add support for the FSM Serial Flash Controller Lee Jones
2013-11-22 16:22 ` [PATCH 12/23] mtd: st_spi_fsm: Search for preferred FSM message sequence configurations Lee Jones
2013-11-22 16:22 ` [PATCH 13/23] mtd: st_spi_fsm: Fetch platform specific configurations Lee Jones
2013-11-22 16:22 ` [PATCH 14/23] mtd: st_spi_fsm: Prepare the read/write FSM message sequence(s) Lee Jones
2013-11-22 16:22 ` [PATCH 15/23] mtd: st_spi_fsm: Fetch boot-device from mode pins Lee Jones
2013-11-22 16:22 ` [PATCH 16/23] mtd: st_spi_fsm: Provide the erase one sector sequence Lee Jones
2013-11-22 16:22 ` [PATCH 17/23] mtd: st_spi_fsm: Provide the sequence for enabling 32bit addressing mode Lee Jones
2013-11-22 16:22 ` [PATCH 18/23] mtd: st_spi_fsm: Prepare read/write sequences according to configuration Lee Jones
2013-11-22 16:22 ` [PATCH 19/23] mtd: st_spi_fsm: Add a check to if the chip can handle an SoC reset Lee Jones
2013-11-22 16:22 ` Lee Jones [this message]
2013-11-22 16:22 ` [PATCH 21/23] mtd: st_spi_fsm: Update the flash Volatile Configuration Register Lee Jones
2013-11-22 16:22 ` [PATCH 22/23] mtd: st_spi_fsm: Provide the default read/write configurations Lee Jones
2013-11-22 16:23 ` [PATCH 23/23] mtd: st_spi_fsm: Supply the N25Qxxx specific read configurations Lee Jones
2013-11-27 4:07 ` [PATCH 00/23] mtd: st_spi_fsm: Add new device Brian Norris
2013-11-27 11:52 ` Lee Jones
2013-11-28 3:34 ` Huang Shijie
2013-11-28 9:07 ` Angus Clark
2013-11-28 9:29 ` Lee Jones
2013-11-29 11:05 ` Huang Shijie
2013-11-29 11:53 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1385137380-28968-21-git-send-email-lee.jones@linaro.org \
--to=lee.jones@linaro.org \
--cc=angus.clark@st.com \
--cc=dwmw2@infradead.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®