mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Suman Anna <s-anna@ti.com>
To: Ohad Ben-Cohen <ohad@wizery.com>, Mark Rutland <mark.rutland@arm.com>
Cc: Tony Lindgren <tony@atomide.com>,
	Kumar Gala <galak@codeaurora.org>, <linux-kernel@vger.kernel.org>,
	<linux-omap@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	Suman Anna <s-anna@ti.com>
Subject: [PATCHv4 6/7] hwspinlock/omap: enable module before reading SYSSTATUS register
Date: Mon, 13 Jan 2014 18:19:23 -0600	[thread overview]
Message-ID: <1389658764-39199-7-git-send-email-s-anna@ti.com> (raw)
In-Reply-To: <1389658764-39199-1-git-send-email-s-anna@ti.com>

The number of hwspinlocks are determined based on the value read
from the IP block's SYSSTATUS register. However, the module may
not be enabled and clocked, and the read may result in a bus error.

This particular issue is seen rather easily on AM33XX, since the
module wakeup is software controlled, and it is disabled out of
reset. Make sure the module is enabled and clocked before reading
the SYSSTATUS register.

Signed-off-by: Suman Anna <s-anna@ti.com>
---
 drivers/hwspinlock/omap_hwspinlock.c | 21 ++++++++++++++-------
 1 file changed, 14 insertions(+), 7 deletions(-)

diff --git a/drivers/hwspinlock/omap_hwspinlock.c b/drivers/hwspinlock/omap_hwspinlock.c
index 9f56fb2..194886e 100644
--- a/drivers/hwspinlock/omap_hwspinlock.c
+++ b/drivers/hwspinlock/omap_hwspinlock.c
@@ -101,10 +101,23 @@ static int omap_hwspinlock_probe(struct platform_device *pdev)
 	if (!io_base)
 		return -ENOMEM;
 
+	/*
+	 * make sure the module is enabled and clocked before reading
+	 * the module SYSSTATUS register
+	 */
+	pm_runtime_enable(&pdev->dev);
+	pm_runtime_get_sync(&pdev->dev);
+
 	/* Determine number of locks */
 	i = readl(io_base + SYSSTATUS_OFFSET);
 	i >>= SPINLOCK_NUMLOCKS_BIT_OFFSET;
 
+	/*
+	 * runtime PM will make sure the clock of this module is
+	 * enabled again iff at least one lock is requested
+	 */
+	pm_runtime_put(&pdev->dev);
+
 	/* one of the four lsb's must be set, and nothing else */
 	if (hweight_long(i & 0xf) != 1 || i > 8) {
 		ret = -EINVAL;
@@ -124,12 +137,6 @@ static int omap_hwspinlock_probe(struct platform_device *pdev)
 	for (i = 0, hwlock = &bank->lock[0]; i < num_locks; i++, hwlock++)
 		hwlock->priv = io_base + LOCK_BASE_OFFSET + sizeof(u32) * i;
 
-	/*
-	 * runtime PM will make sure the clock of this module is
-	 * enabled iff at least one lock is requested
-	 */
-	pm_runtime_enable(&pdev->dev);
-
 	ret = hwspin_lock_register(bank, &pdev->dev, &omap_hwspinlock_ops,
 						base_id, num_locks);
 	if (ret)
@@ -138,9 +145,9 @@ static int omap_hwspinlock_probe(struct platform_device *pdev)
 	return 0;
 
 reg_fail:
-	pm_runtime_disable(&pdev->dev);
 	kfree(bank);
 iounmap_base:
+	pm_runtime_disable(&pdev->dev);
 	iounmap(io_base);
 	return ret;
 }
-- 
1.8.4.3


  parent reply	other threads:[~2014-01-14  0:21 UTC|newest]

Thread overview: 44+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-01-14  0:19 [PATCHv4 0/7] omap hwspinlock dt support Suman Anna
2014-01-14  0:19 ` [PATCHv4 1/7] Documentation: dt: add common bindings for hwspinlock Suman Anna
2014-01-14  0:19 ` [PATCHv4 2/7] Documentation: dt: add the omap hwspinlock bindings document Suman Anna
2014-01-14  0:19 ` [PATCHv4 3/7] hwspinlock/core: maintain a list of registered hwspinlock banks Suman Anna
2014-01-14  0:19 ` [PATCHv4 4/7] hwspinlock/core: add common OF helpers Suman Anna
2014-02-07 22:49   ` Bjorn Andersson
2014-02-10 19:14     ` Suman Anna
2014-03-02  5:14       ` Ohad Ben-Cohen
2014-03-02 20:19         ` Bjorn Andersson
2014-03-03 18:46           ` Suman Anna
2014-03-04 17:38           ` Suman Anna
2014-03-13 16:43             ` Josh Cartwright
2014-03-14  8:58             ` Ohad Ben-Cohen
2014-03-14 13:12           ` Ohad Ben-Cohen
2014-03-14 15:23             ` Josh Cartwright
2014-03-15 17:32               ` Ohad Ben-Cohen
2014-09-26 14:40   ` Bjorn Andersson
2014-09-26 16:25     ` Suman Anna
2014-10-06  9:44       ` Ohad Ben-Cohen
2014-11-06 18:24         ` Suman Anna
2014-11-07  5:06           ` Ohad Ben-Cohen
2014-01-14  0:19 ` [PATCHv4 5/7] hwspinlock/omap: add support for dt nodes Suman Anna
2014-01-14  0:19 ` Suman Anna [this message]
2014-01-14 13:10   ` [PATCHv4 6/7] hwspinlock/omap: enable module before reading SYSSTATUS register Felipe Balbi
2014-01-14 14:04     ` Felipe Balbi
2014-01-14 16:56       ` Anna, Suman
2014-01-15 23:46         ` Anna, Suman
2014-01-15 23:36   ` [UPDATED PATCHv4 " Suman Anna
2014-01-14  0:19 ` [PATCHv4 7/7] hwspinlock/omap: enable build for AM33xx, AM43xx & DRA7xx Suman Anna
2014-01-14 13:12   ` Felipe Balbi
2014-01-14 16:51     ` Anna, Suman
2014-01-14 17:29       ` Felipe Balbi
2014-01-14 18:36         ` Anna, Suman
2014-01-14 13:12 ` [PATCHv4 0/7] omap hwspinlock dt support Felipe Balbi
2014-02-10 19:27 ` Suman Anna
2014-02-24 18:14   ` Suman Anna
2014-03-14 20:10     ` Ohad Ben-Cohen
2014-03-14 23:58       ` Suman Anna
2014-03-17 14:23         ` Ohad Ben-Cohen
2014-03-17 19:10           ` Suman Anna
2014-03-17 19:47             ` Ohad Ben-Cohen
2014-03-17 23:46               ` Suman Anna
2014-03-18 13:35                 ` Ohad Ben-Cohen
2014-03-31 22:45                   ` Suman Anna

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1389658764-39199-7-git-send-email-s-anna@ti.com \
    --to=s-anna@ti.com \
    --cc=devicetree@vger.kernel.org \
    --cc=galak@codeaurora.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=ohad@wizery.com \
    --cc=tony@atomide.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®