From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1752730AbaAXIro (ORCPT ); Fri, 24 Jan 2014 03:47:44 -0500 Received: from albert.telenet-ops.be ([195.130.137.90]:49663 "EHLO albert.telenet-ops.be" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752448AbaAXIoS (ORCPT ); Fri, 24 Jan 2014 03:44:18 -0500 From: Geert Uytterhoeven To: Mark Brown Cc: linux-spi@vger.kernel.org, linux-sh@vger.kernel.org, linux-kernel@vger.kernel.org, Geert Uytterhoeven Subject: [PATCH v3 10/14] spi: rspi: Add support for loopback mode Date: Fri, 24 Jan 2014 09:44:00 +0100 Message-Id: <1390553044-11860-11-git-send-email-geert@linux-m68k.org> X-Mailer: git-send-email 1.7.9.5 In-Reply-To: <1390553044-11860-1-git-send-email-geert@linux-m68k.org> References: <1390553044-11860-1-git-send-email-geert@linux-m68k.org> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org From: Geert Uytterhoeven Add support for specifying loopback mode. Signed-off-by: Geert Uytterhoeven --- v3: - This became a lot simpler after merging the send_pio() and receive_pio() methods drivers/spi/spi-rspi.c | 22 ++++++++++++++-------- 1 file changed, 14 insertions(+), 8 deletions(-) diff --git a/drivers/spi/spi-rspi.c b/drivers/spi/spi-rspi.c index 0c7556978d2e..28db8770aaf3 100644 --- a/drivers/spi/spi-rspi.c +++ b/drivers/spi/spi-rspi.c @@ -183,8 +183,9 @@ struct rspi_data { struct spi_master *master; wait_queue_head_t wait; struct clk *clk; - u8 spsr; u16 spcmd; + u8 spsr; + u8 sppcr; int rx_irq, tx_irq; const struct spi_ops *ops; @@ -252,8 +253,8 @@ static int rspi_set_config_register(struct rspi_data *rspi, int access_size) { int spbr; - /* Sets output mode(CMOS) and MOSI signal(from previous transfer) */ - rspi_write8(rspi, 0x00, RSPI_SPPCR); + /* Sets output mode, MOSI signal, and (optionally) loopback */ + rspi_write8(rspi, rspi->sppcr, RSPI_SPPCR); /* Sets transfer bit rate */ spbr = clk_get_rate(rspi->clk) / (2 * rspi->max_speed_hz) - 1; @@ -288,8 +289,8 @@ static int rspi_rz_set_config_register(struct rspi_data *rspi, int access_size) { int spbr; - /* Sets output mode */ - rspi_write8(rspi, 0x00, RSPI_SPPCR); + /* Sets output mode, MOSI signal, and (optionally) loopback */ + rspi_write8(rspi, rspi->sppcr, RSPI_SPPCR); /* Sets transfer bit rate */ spbr = clk_get_rate(rspi->clk) / (2 * rspi->max_speed_hz) - 1; @@ -322,8 +323,8 @@ static int qspi_set_config_register(struct rspi_data *rspi, int access_size) u16 spcmd; int spbr; - /* Sets output mode(CMOS) and MOSI signal(from previous transfer) */ - rspi_write8(rspi, 0x00, RSPI_SPPCR); + /* Sets output mode, MOSI signal, and (optionally) loopback */ + rspi_write8(rspi, rspi->sppcr, RSPI_SPPCR); /* Sets transfer bit rate */ spbr = clk_get_rate(rspi->clk) / (2 * rspi->max_speed_hz); @@ -829,6 +830,11 @@ static int rspi_setup(struct spi_device *spi) if (spi->mode & SPI_CPHA) rspi->spcmd |= SPCMD_CPHA; + /* CMOS output mode and MOSI signal from previous transfer */ + rspi->sppcr = 0; + if (spi->mode & SPI_LOOP) + rspi->sppcr |= SPPCR_SPLP; + set_config_register(rspi, 8); return 0; @@ -1050,7 +1056,7 @@ static int rspi_probe(struct platform_device *pdev) master->cleanup = rspi_cleanup; master->prepare_message = rspi_prepare_message; master->unprepare_message = rspi_unprepare_message; - master->mode_bits = SPI_CPHA | SPI_CPOL; + master->mode_bits = SPI_CPHA | SPI_CPOL | SPI_LOOP; ret = platform_get_irq_byname(pdev, "rx"); if (ret < 0) { -- 1.7.9.5