From: Nishanth Menon <nm@ti.com>
To: "Benoît Cousson" <bcousson@baylibre.com>,
"Tony Lindgren" <tony@atomide.com>
Cc: <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <linux-omap@vger.kernel.org>,
Nishanth Menon <nm@ti.com>
Subject: [PATCH 4/4] ARM: dts: DRA7: Add device nodes for ABB
Date: Wed, 29 Jan 2014 17:46:16 -0600 [thread overview]
Message-ID: <1391039177-25284-5-git-send-email-nm@ti.com> (raw)
In-Reply-To: <1391039177-25284-1-git-send-email-nm@ti.com>
Add ABB device nodes for DRA7 family of devices. Data is based on
DRA7 Technical Reference Manual revision I (Sept 2013)
Signed-off-by: Nishanth Menon <nm@ti.com>
---
Depends on https://patchwork.kernel.org/patch/3530111/
arch/arm/boot/dts/dra7.dtsi | 132 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 132 insertions(+)
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 1fd75aa..23a2a11 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -559,6 +559,138 @@
status = "disabled";
};
+ abb_mpu: regulator-abb-mpu {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_mpu";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
+ <0x4ae06014 0x4>, <0x4a003b20 0x8>,
+ <0x4ae0c158 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x80>;
+ /* LDOVBBMPU_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBMPU_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1060000 0 0x0 0 0x02000000 0x01F00000
+ 1160000 0 0x4 0 0x02000000 0x01F00000
+ 1210000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
+ abb_ivahd: regulator-abb-ivahd {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_ivahd";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
+ <0x4ae06010 0x4>, <0x4a0025cc 0x8>,
+ <0x4a002470 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x40000000>;
+ /* LDOVBBIVA_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBIVA_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1055000 0 0x0 0 0x02000000 0x01F00000
+ 1150000 0 0x4 0 0x02000000 0x01F00000
+ 1250000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
+ abb_dspeve: regulator-abb-dspeve {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_dspeve";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
+ <0x4ae06010 0x4>, <0x4a0025e0 0x8>,
+ <0x4a00246c 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x20000000>;
+ /* LDOVBBDSPEVE_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBDSPEVE_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1055000 0 0x0 0 0x02000000 0x01F00000
+ 1150000 0 0x4 0 0x02000000 0x01F00000
+ 1250000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
+ abb_gpu: regulator-abb-gpu {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_gpu";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
+ <0x4ae06010 0x4>, <0x4a003b08 0x8>,
+ <0x4ae0c154 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x10000000>;
+ /* LDOVBBGPU_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBGPU_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1090000 0 0x0 0 0x02000000 0x01F00000
+ 1210000 0 0x4 0 0x02000000 0x01F00000
+ 1280000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
mcspi1: spi@48098000 {
compatible = "ti,omap4-mcspi";
reg = <0x48098000 0x200>;
--
1.7.9.5
next prev parent reply other threads:[~2014-01-29 23:46 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-01-29 23:46 [PATCH 0/4] ARM: dts: OMAP3630+: Add ABB device nodes Nishanth Menon
2014-01-29 23:46 ` [PATCH 1/4] ARM: dts: OMAP36xx: Add device node for ABB Nishanth Menon
2014-01-29 23:46 ` [PATCH 2/4] ARM: dts: OMAP4: Add device nodes " Nishanth Menon
2014-01-29 23:46 ` [PATCH 3/4] ARM: dts: OMAP5: " Nishanth Menon
2014-02-20 16:36 ` Nishanth Menon
2014-01-29 23:46 ` Nishanth Menon [this message]
2014-03-05 19:47 ` [PATCH 0/4] ARM: dts: OMAP3630+: Add ABB device nodes Tony Lindgren
2014-03-05 19:49 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1391039177-25284-5-git-send-email-nm@ti.com \
--to=nm@ti.com \
--cc=bcousson@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®