From: Tim Kryger <tim.kryger@linaro.org>
To: Chris Ball <chris@printf.net>, Ulf Hansson <ulf.hansson@linaro.org>
Cc: Tim Kryger <tim.kryger@linaro.org>,
Mike Looijmans <mike.looijmans@topic.nl>,
Andrew Bresticker <abrestic@chromium.org>,
"Linux MMC List" <linux-mmc@vger.kernel.org>,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Subject: [PATCH 2/2] mmc: sdhci: Use common mmc_regulator_get_supply
Date: Thu, 17 Apr 2014 17:47:01 -0700 [thread overview]
Message-ID: <1397782021-31396-3-git-send-email-tim.kryger@linaro.org> (raw)
In-Reply-To: <1397782021-31396-1-git-send-email-tim.kryger@linaro.org>
Replace some buggy code with a call to mmc_regulator_get_supply.
When external regulator provides VDD, ocr_avail is set directly based on
the supported voltage range. This allows for the use of regulators that
can't provide exactly 1.8v, 3.0v, or 3.3v. Commit cec2e21 had attempted
to address this by relaxing the range checks in the SDHCI driver but it
set the capabilities as an intermediate step which meant ocr_avail could
get bits set for unsupported voltages.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
---
drivers/mmc/host/sdhci.c | 67 +++++++++++++---------------------------------
1 file changed, 18 insertions(+), 49 deletions(-)
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index 16fba66..2d081d8 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -1438,7 +1438,8 @@ static void sdhci_do_set_ios(struct sdhci_host *host, struct mmc_ios *ios)
if (host->flags & SDHCI_DEVICE_DEAD) {
spin_unlock_irqrestore(&host->lock, flags);
- if (mmc->supply.vmmc && ios->power_mode == MMC_POWER_OFF)
+ if (!IS_ERR(mmc->supply.vmmc) &&
+ ios->power_mode == MMC_POWER_OFF)
mmc_regulator_set_ocr(host->mmc, mmc->supply.vmmc, 0);
return;
}
@@ -1464,7 +1465,7 @@ static void sdhci_do_set_ios(struct sdhci_host *host, struct mmc_ios *ios)
else
vdd_bit = sdhci_set_power(host, ios->vdd);
- if (mmc->supply.vmmc && vdd_bit != -1) {
+ if (!IS_ERR(mmc->supply.vmmc) && vdd_bit != -1) {
spin_unlock_irqrestore(&host->lock, flags);
mmc_regulator_set_ocr(host->mmc, mmc->supply.vmmc, vdd_bit);
spin_lock_irqsave(&host->lock, flags);
@@ -1762,7 +1763,7 @@ static int sdhci_do_start_signal_voltage_switch(struct sdhci_host *host,
ctrl &= ~SDHCI_CTRL_VDD_180;
sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
- if (mmc->supply.vqmmc) {
+ if (!IS_ERR(mmc->supply.vqmmc)) {
ret = regulator_set_voltage(mmc->supply.vqmmc, 2700000,
3600000);
if (ret) {
@@ -1784,7 +1785,7 @@ static int sdhci_do_start_signal_voltage_switch(struct sdhci_host *host,
return -EAGAIN;
case MMC_SIGNAL_VOLTAGE_180:
- if (mmc->supply.vqmmc) {
+ if (!IS_ERR(mmc->supply.vqmmc)) {
ret = regulator_set_voltage(mmc->supply.vqmmc,
1700000, 1950000);
if (ret) {
@@ -1814,7 +1815,7 @@ static int sdhci_do_start_signal_voltage_switch(struct sdhci_host *host,
return -EAGAIN;
case MMC_SIGNAL_VOLTAGE_120:
- if (mmc->supply.vqmmc) {
+ if (!IS_ERR(mmc->supply.vqmmc)) {
ret = regulator_set_voltage(mmc->supply.vqmmc, 1100000,
1300000);
if (ret) {
@@ -2979,15 +2980,12 @@ int sdhci_add_host(struct sdhci_host *host)
!(host->mmc->caps & MMC_CAP_NONREMOVABLE))
mmc->caps |= MMC_CAP_NEEDS_POLL;
+ /* If there are external regulators, get them */
+ if (mmc_regulator_get_supply(mmc) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+
/* If vqmmc regulator and no 1.8V signalling, then there's no UHS */
- mmc->supply.vqmmc = regulator_get_optional(mmc_dev(mmc), "vqmmc");
- if (IS_ERR_OR_NULL(mmc->supply.vqmmc)) {
- if (PTR_ERR(mmc->supply.vqmmc) < 0) {
- pr_info("%s: no vqmmc regulator found\n",
- mmc_hostname(mmc));
- mmc->supply.vqmmc = NULL;
- }
- } else {
+ if (!IS_ERR(mmc->supply.vqmmc)) {
ret = regulator_enable(mmc->supply.vqmmc);
if (!regulator_is_supported_voltage(mmc->supply.vqmmc, 1700000,
1950000))
@@ -3058,34 +3056,6 @@ int sdhci_add_host(struct sdhci_host *host)
ocr_avail = 0;
- mmc->supply.vmmc = regulator_get_optional(mmc_dev(mmc), "vmmc");
- if (IS_ERR_OR_NULL(mmc->supply.vmmc)) {
- if (PTR_ERR(mmc->supply.vmmc) < 0) {
- pr_info("%s: no vmmc regulator found\n",
- mmc_hostname(mmc));
- mmc->supply.vmmc = NULL;
- }
- }
-
-#ifdef CONFIG_REGULATOR
- /*
- * Voltage range check makes sense only if regulator reports
- * any voltage value.
- */
- if (mmc->supply.vmmc && regulator_get_voltage(mmc->supply.vmmc) > 0) {
- ret = regulator_is_supported_voltage(mmc->supply.vmmc, 2700000,
- 3600000);
- if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_330)))
- caps[0] &= ~SDHCI_CAN_VDD_330;
- if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_300)))
- caps[0] &= ~SDHCI_CAN_VDD_300;
- ret = regulator_is_supported_voltage(mmc->supply.vmmc, 1700000,
- 1950000);
- if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_180)))
- caps[0] &= ~SDHCI_CAN_VDD_180;
- }
-#endif /* CONFIG_REGULATOR */
-
/*
* According to SD Host Controller spec v3.00, if the Host System
* can afford more than 150mA, Host Driver should set XPC to 1. Also
@@ -3094,7 +3064,7 @@ int sdhci_add_host(struct sdhci_host *host)
* value.
*/
max_current_caps = sdhci_readl(host, SDHCI_MAX_CURRENT);
- if (!max_current_caps && mmc->supply.vmmc) {
+ if (!max_current_caps && !IS_ERR(mmc->supply.vmmc)) {
u32 curr = regulator_get_current_limit(mmc->supply.vmmc);
if (curr > 0) {
@@ -3135,8 +3105,11 @@ int sdhci_add_host(struct sdhci_host *host)
SDHCI_MAX_CURRENT_MULTIPLIER;
}
+ if (mmc->ocr_avail)
+ ocr_avail &= mmc->ocr_avail;
+
if (host->ocr_mask)
- ocr_avail = host->ocr_mask;
+ ocr_avail &= host->ocr_mask;
mmc->ocr_avail = ocr_avail;
mmc->ocr_avail_sdio = ocr_avail;
@@ -3330,15 +3303,11 @@ void sdhci_remove_host(struct sdhci_host *host, int dead)
tasklet_kill(&host->card_tasklet);
tasklet_kill(&host->finish_tasklet);
- if (mmc->supply.vmmc) {
+ if (!IS_ERR(mmc->supply.vmmc))
regulator_disable(mmc->supply.vmmc);
- regulator_put(mmc->supply.vmmc);
- }
- if (mmc->supply.vqmmc) {
+ if (!IS_ERR(mmc->supply.vqmmc))
regulator_disable(mmc->supply.vqmmc);
- regulator_put(mmc->supply.vqmmc);
- }
kfree(host->adma_desc);
kfree(host->align_buffer);
--
1.7.9.5
next prev parent reply other threads:[~2014-04-18 0:47 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-04-18 0:46 [PATCH 0/2] SDHCI should use more common MMC structs and functions Tim Kryger
2014-04-18 0:47 ` [PATCH 1/2] mmc: sdhci: Use supplies in common mmc_host struct Tim Kryger
2014-04-18 0:47 ` Tim Kryger [this message]
2014-04-24 8:34 ` [PATCH 0/2] SDHCI should use more common MMC structs and functions Ulf Hansson
2014-04-24 22:35 ` Tim Kryger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1397782021-31396-3-git-send-email-tim.kryger@linaro.org \
--to=tim.kryger@linaro.org \
--cc=abrestic@chromium.org \
--cc=chris@printf.net \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=mike.looijmans@topic.nl \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®