From: Alexandre Belloni <alexandre.belloni@free-electrons.com>
To: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>,
Boris Brezillon <boris.brezillon@free-electrons.com>,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
Alexandre Belloni <alexandre.belloni@free-electrons.com>
Subject: [PATCHv2 04/32] ARM: at91/dt: rm9200: define clocks
Date: Mon, 7 Jul 2014 22:23:21 +0200 [thread overview]
Message-ID: <1404764629-29136-5-git-send-email-alexandre.belloni@free-electrons.com> (raw)
In-Reply-To: <1404764629-29136-1-git-send-email-alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
arch/arm/boot/dts/at91rm9200.dtsi | 304 ++++++++++++++++++++++++++++++++++++++
1 file changed, 304 insertions(+)
diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi
index c61b16fba79b..65ccf564b9a5 100644
--- a/arch/arm/boot/dts/at91rm9200.dtsi
+++ b/arch/arm/boot/dts/at91rm9200.dtsi
@@ -14,6 +14,7 @@
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/at91.h>
/ {
model = "Atmel AT91RM9200 family SoC";
@@ -51,6 +52,20 @@
reg = <0x20000000 0x04000000>;
};
+ clocks {
+ slow_xtal: slow_xtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ main_xtal: main_xtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+ };
+
ahb {
compatible = "simple-bus";
#address-cells = <1>;
@@ -79,6 +94,260 @@
pmc: pmc@fffffc00 {
compatible = "atmel,at91rm9200-pmc";
reg = <0xfffffc00 0x100>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ interrupt-controller;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #interrupt-cells = <1>;
+
+ main_osc: main_osc {
+ compatible = "atmel,at91rm9200-clk-main-osc";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_MOSCS>;
+ clocks = <&main_xtal>;
+ };
+
+ main: mainck {
+ compatible = "atmel,at91rm9200-clk-main";
+ #clock-cells = <0>;
+ clocks = <&main_osc>;
+ };
+
+ plla: pllack {
+ compatible = "atmel,at91rm9200-clk-pll";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_LOCKA>;
+ clocks = <&main>;
+ reg = <0>;
+ atmel,clk-input-range = <1000000 32000000>;
+ #atmel,pll-clk-output-range-cells = <3>;
+ atmel,pll-clk-output-ranges = <80000000 160000000 0>,
+ <150000000 180000000 2>;
+ };
+
+ pllb: pllbck {
+ compatible = "atmel,at91rm9200-clk-pll";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_LOCKB>;
+ clocks = <&main>;
+ reg = <1>;
+ atmel,clk-input-range = <1000000 32000000>;
+ #atmel,pll-clk-output-range-cells = <3>;
+ atmel,pll-clk-output-ranges = <80000000 160000000 0>,
+ <150000000 180000000 2>;
+ };
+
+ mck: masterck {
+ compatible = "atmel,at91rm9200-clk-master";
+ #clock-cells = <0>;
+ interrupts-extended = <&pmc AT91_PMC_MCKRDY>;
+ clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>;
+ atmel,clk-output-range = <0 80000000>;
+ atmel,clk-divisors = <1 2 3 4>;
+ };
+
+ usb: usbck {
+ compatible = "atmel,at91rm9200-clk-usb";
+ #clock-cells = <0>;
+ atmel,clk-divisors = <1 2>;
+ clocks = <&pllb>;
+ };
+
+ prog: progck {
+ compatible = "atmel,at91rm9200-clk-programmable";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <&pmc>;
+ clocks = <&slow_xtal>, <&main>, <&plla>, <&pllb>;
+
+ prog0: prog0 {
+ #clock-cells = <0>;
+ reg = <0>;
+ interrupts = <AT91_PMC_PCKRDY(0)>;
+ };
+
+ prog1: prog1 {
+ #clock-cells = <0>;
+ reg = <1>;
+ interrupts = <AT91_PMC_PCKRDY(1)>;
+ };
+
+ prog2: prog2 {
+ #clock-cells = <0>;
+ reg = <2>;
+ interrupts = <AT91_PMC_PCKRDY(2)>;
+ };
+
+ prog3: prog3 {
+ #clock-cells = <0>;
+ reg = <3>;
+ interrupts = <AT91_PMC_PCKRDY(3)>;
+ };
+ };
+
+ systemck {
+ compatible = "atmel,at91rm9200-clk-system";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ udpck: udpck {
+ #clock-cells = <0>;
+ reg = <2>;
+ clocks = <&usb>;
+ };
+
+ uhpck: uhpck {
+ #clock-cells = <0>;
+ reg = <4>;
+ clocks = <&usb>;
+ };
+
+ pck0: pck0 {
+ #clock-cells = <0>;
+ reg = <8>;
+ clocks = <&prog0>;
+ };
+
+ pck1: pck1 {
+ #clock-cells = <0>;
+ reg = <9>;
+ clocks = <&prog1>;
+ };
+
+ pck2: pck2 {
+ #clock-cells = <0>;
+ reg = <10>;
+ clocks = <&prog2>;
+ };
+
+ pck3: pck3 {
+ #clock-cells = <0>;
+ reg = <11>;
+ clocks = <&prog3>;
+ };
+ };
+
+ periphck {
+ compatible = "atmel,at91rm9200-clk-peripheral";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&mck>;
+
+ pioA_clk: pioA_clk {
+ #clock-cells = <0>;
+ reg = <2>;
+ };
+
+ pioB_clk: pioB_clk {
+ #clock-cells = <0>;
+ reg = <3>;
+ };
+
+ pioC_clk: pioC_clk {
+ #clock-cells = <0>;
+ reg = <4>;
+ };
+
+ pioD_clk: pioD_clk {
+ #clock-cells = <0>;
+ reg = <5>;
+ };
+
+ usart0_clk: usart0_clk {
+ #clock-cells = <0>;
+ reg = <6>;
+ };
+
+ usart1_clk: usart1_clk {
+ #clock-cells = <0>;
+ reg = <7>;
+ };
+
+ usart2_clk: usart2_clk {
+ #clock-cells = <0>;
+ reg = <8>;
+ };
+
+ usart3_clk: usart3_clk {
+ #clock-cells = <0>;
+ reg = <9>;
+ };
+
+ mci0_clk: mci0_clk {
+ #clock-cells = <0>;
+ reg = <10>;
+ };
+
+ udc_clk: udc_clk {
+ #clock-cells = <0>;
+ reg = <11>;
+ };
+
+ twi0_clk: twi0_clk {
+ reg = <12>;
+ #clock-cells = <0>;
+ };
+
+ spi0_clk: spi0_clk {
+ #clock-cells = <0>;
+ reg = <13>;
+ };
+
+ ssc0_clk: ssc0_clk {
+ #clock-cells = <0>;
+ reg = <14>;
+ };
+
+ ssc1_clk: ssc1_clk {
+ #clock-cells = <0>;
+ reg = <15>;
+ };
+
+ ssc2_clk: ssc2_clk {
+ #clock-cells = <0>;
+ reg = <16>;
+ };
+
+ tc0_clk: tc0_clk {
+ #clock-cells = <0>;
+ reg = <17>;
+ };
+
+ tc1_clk: tc1_clk {
+ #clock-cells = <0>;
+ reg = <18>;
+ };
+
+ tc2_clk: tc2_clk {
+ #clock-cells = <0>;
+ reg = <19>;
+ };
+
+ tc3_clk: tc3_clk {
+ #clock-cells = <0>;
+ reg = <20>;
+ };
+
+ tc4_clk: tc4_clk {
+ #clock-cells = <0>;
+ reg = <21>;
+ };
+
+ tc5_clk: tc5_clk {
+ #clock-cells = <0>;
+ reg = <22>;
+ };
+
+ ohci_clk: ohci_clk {
+ #clock-cells = <0>;
+ reg = <23>;
+ };
+
+ macb0_clk: macb0_clk {
+ #clock-cells = <0>;
+ reg = <24>;
+ };
+ };
};
st: timer@fffffd00 {
@@ -93,6 +362,8 @@
interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0
18 IRQ_TYPE_LEVEL_HIGH 0
19 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&tc0_clk>, <&tc1_clk>, <&tc2_clk>;
+ clock-names = "t0_clk", "t1_clk", "t2_clk";
};
tcb1: timer@fffa4000 {
@@ -101,6 +372,8 @@
interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0
21 IRQ_TYPE_LEVEL_HIGH 0
22 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&tc3_clk>, <&tc4_clk>, <&tc5_clk>;
+ clock-names = "t0_clk", "t1_clk", "t2_clk";
};
i2c0: i2c@fffb8000 {
@@ -109,6 +382,7 @@
interrupts = <12 IRQ_TYPE_LEVEL_HIGH 6>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_twi>;
+ clocks = <&twi0_clk>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -118,6 +392,8 @@
compatible = "atmel,hsmci";
reg = <0xfffb4000 0x4000>;
interrupts = <10 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&mci0_clk>;
+ clock-names = "mci_clk";
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
@@ -130,6 +406,8 @@
interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
+ clocks = <&ssc0_clk>;
+ clock-names = "pclk";
status = "disable";
};
@@ -139,6 +417,8 @@
interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
+ clocks = <&ssc1_clk>;
+ clock-names = "pclk";
status = "disable";
};
@@ -148,6 +428,8 @@
interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ssc2_tx &pinctrl_ssc2_rx>;
+ clocks = <&ssc2_clk>;
+ clock-names = "pclk";
status = "disable";
};
@@ -158,6 +440,8 @@
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb_rmii>;
+ clocks = <&macb0_clk>;
+ clock-names = "ether_clk";
status = "disabled";
};
@@ -496,6 +780,7 @@
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
+ clocks = <&pioA_clk>;
};
pioB: gpio@fffff600 {
@@ -506,6 +791,7 @@
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
+ clocks = <&pioB_clk>;
};
pioC: gpio@fffff800 {
@@ -516,6 +802,7 @@
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
+ clocks = <&pioC_clk>;
};
pioD: gpio@fffffa00 {
@@ -526,6 +813,7 @@
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
+ clocks = <&pioD_clk>;
};
};
@@ -535,6 +823,8 @@
interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
+ clocks = <&mck>;
+ clock-names = "usart";
status = "disabled";
};
@@ -546,6 +836,8 @@
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0>;
+ clocks = <&usart0_clk>;
+ clock-names = "usart";
status = "disabled";
};
@@ -557,6 +849,8 @@
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
+ clocks = <&usart1_clk>;
+ clock-names = "usart";
status = "disabled";
};
@@ -568,6 +862,8 @@
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
+ clocks = <&usart2_clk>;
+ clock-names = "usart";
status = "disabled";
};
@@ -579,6 +875,8 @@
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
+ clocks = <&usart3_clk>;
+ clock-names = "usart";
status = "disabled";
};
@@ -586,6 +884,8 @@
compatible = "atmel,at91rm9200-udc";
reg = <0xfffb0000 0x4000>;
interrupts = <11 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&udc_clk>, <&udpck>;
+ clock-names = "pclk", "hclk";
status = "disabled";
};
@@ -597,6 +897,8 @@
interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi0>;
+ clocks = <&spi0_clk>;
+ clock-names = "spi_clk";
status = "disabled";
};
};
@@ -622,6 +924,8 @@
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00300000 0x100000>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&usb>, <&ohci_clk>, <&ohci_clk>, <&uhpck>;
+ clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck";
status = "disabled";
};
};
--
1.9.1
next prev parent reply other threads:[~2014-07-07 20:32 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-07-07 20:23 [PATCHv2 00/32] ARM: at91: Switch remaining SoCs and boards to CCF Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 01/32] Documentation: dt: document all the atmel pmc compatibles Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 02/32] ARM: at91/dt: ariag25: define crystals frequencies Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 03/32] ARM: at91: prepare common clk transition for rm9200 Alexandre Belloni
2014-07-07 20:23 ` Alexandre Belloni [this message]
2014-07-07 20:23 ` [PATCHv2 05/32] ARM: at91: move at91rm9200 SoC to the CCF Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 06/32] ARM: at91/dt: at91rm9200ek: define crystals frequencies Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 07/32] ARM: at91: prepare common clk transition for sam9260 Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 08/32] ARM: at91/dt: sam9260: define clocks Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 09/32] ARM: at91/dt: sam9g20: " Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 10/32] ARM: at91: move at91sam9260 SoCs to the CCF Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 11/32] ARM: at91/dt: at91sam9g20ek: define crystals frequencies Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 12/32] ARM: at91/dt: foxg20: " Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 13/32] ARM: at91/dt: usb_a9260: " Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 14/32] ARM: at91/dt: tny_a9260: " Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 15/32] ARM: at91/dt: qil_a9260: " Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 16/32] ARM: at91/dt: mpa1600: define crytals frequencies Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 17/32] ARM: at91/dt: ge863-pro3: define crystals frequencies Alexandre Belloni
2014-07-08 6:11 ` Jiří Prchal
2014-07-08 11:31 ` Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 18/32] ARM: at91/dt: ethernut5: " Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 19/32] ARM: at91/dt: animeo_ip: " Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 20/32] ARM: at91/dt: kizbox: define main crystal frequency Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 21/32] ARM: at91: prepare common clk transition for sam9g45 Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 22/32] ARM: at91/dt: sam9g45: define clocks Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 23/32] ARM: at91: move at91sam9g45 SoC to the CCF Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 24/32] ARM: at91/dt: sam9m10g45ek: define crystals frequencies Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 25/32] ARM: at91/dt: pm9g45: " Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 26/32] ARM: at91/dt: cosino define " Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 27/32] ARM: at91: prepare common clk transition for sam9263 Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 28/32] ARM: at91/dt: sam9263: define clocks Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 29/32] ARM: at91: move at91sam9263 SoC to the CCF Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 30/32] ARM: at91/dt: sam9263ek: define crystals frequencies Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 31/32] ARM: at91/dt: tny_a9263: " Alexandre Belloni
2014-07-07 20:23 ` [PATCHv2 32/32] ARM: at91/dt: usb_a9263: " Alexandre Belloni
2014-07-08 17:11 ` [PATCHv2 00/32] ARM: at91: Switch remaining SoCs and boards to CCF Nicolas Ferre
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1404764629-29136-5-git-send-email-alexandre.belloni@free-electrons.com \
--to=alexandre.belloni@free-electrons.com \
--cc=boris.brezillon@free-electrons.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nicolas.ferre@atmel.com \
--cc=plagnioj@jcrosoft.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®