From: Soren Brinkmann <soren.brinkmann@xilinx.com>
To: Linus Walleij <linus.walleij@linaro.org>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>,
"Michal Simek" <michal.simek@xilinx.com>,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
"Alessandro Rubini" <rubini@unipv.it>,
"Heiko Stuebner" <heiko@sntech.de>,
"Laurent Pinchart" <laurent.pinchart@ideasonboard.com>,
linux-rockchip@lists.infradead.org, linux-sh@vger.kernel.org,
"Ivan T. Ivanov" <iivanov@mm-sol.com>,
"Bjorn Andersson" <bjorn.andersson@sonymobile.com>,
"Beniamino Galvani" <b.galvani@gmail.com>
Subject: [PATCH v2 6/7] ARM: zynq: DT: Add pinctrl information
Date: Thu, 27 Nov 2014 17:26:32 -0800 [thread overview]
Message-ID: <1417137993-8337-7-git-send-email-soren.brinkmann@xilinx.com> (raw)
In-Reply-To: <1417137993-8337-1-git-send-email-soren.brinkmann@xilinx.com>
Add pinctrl descriptions to the zc702 and zc706 device trees.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
---
Changes since v1:
- remove 'pinctrl-' prefix for pinctrl sub-nodes
- separate config and mux nodes
Changes since RFC v2:
- add pinconf properties to zc702 mdio node
- remove arguments from bias-related props
Changes since RFC v1:
- separate DT changes into their own patch
---
arch/arm/boot/dts/zynq-7000.dtsi | 8 +-
arch/arm/boot/dts/zynq-zc702.dts | 181 +++++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/zynq-zc706.dts | 152 ++++++++++++++++++++++++++++++++
3 files changed, 340 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi
index 24036c440440..37d7fe36a129 100644
--- a/arch/arm/boot/dts/zynq-7000.dtsi
+++ b/arch/arm/boot/dts/zynq-7000.dtsi
@@ -238,7 +238,7 @@
slcr: slcr@f8000000 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "xlnx,zynq-slcr", "syscon";
+ compatible = "xlnx,zynq-slcr", "syscon", "simple-bus";
reg = <0xF8000000 0x1000>;
ranges;
clkc: clkc@100 {
@@ -259,6 +259,12 @@
"dbg_trc", "dbg_apb";
reg = <0x100 0x100>;
};
+
+ pinctrl0: pinctrl@700 {
+ compatible = "xlnx,pinctrl-zynq";
+ reg = <0x700 0x200>;
+ syscon = <&slcr>;
+ };
};
dmac_s: dmac@f8003000 {
diff --git a/arch/arm/boot/dts/zynq-zc702.dts b/arch/arm/boot/dts/zynq-zc702.dts
index 94e2cda6f9b6..1e3d800e5b2e 100644
--- a/arch/arm/boot/dts/zynq-zc702.dts
+++ b/arch/arm/boot/dts/zynq-zc702.dts
@@ -40,21 +40,32 @@
&can0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can0_default>;
};
&gem0 {
status = "okay";
phy-mode = "rgmii-id";
phy-handle = <ðernet_phy>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem0_default>;
ethernet_phy: ethernet-phy@7 {
reg = <7>;
};
};
+&gpio0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio0_default>;
+};
+
&i2c0 {
status = "okay";
clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
i2cswitch@74 {
compatible = "nxp,pca9548";
@@ -128,10 +139,180 @@
};
};
+&pinctrl0 {
+ pinctrl_can0_default: can0-default {
+ mux {
+ function = "can0";
+ groups = "can0_9_grp";
+ };
+
+ conf {
+ groups = "can0_9_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-rx {
+ pins = "MIO46";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO47";
+ bias-disable;
+ };
+ };
+
+ pinctrl_gem0_default: gem0-default {
+ mux {
+ function = "ethernet0";
+ groups = "ethernet0_0_grp";
+ };
+
+ conf {
+ groups = "ethernet0_0_grp";
+ slew-rate = <0>;
+ io-standard = <4>;
+ };
+
+ conf-rx {
+ pins = "MIO22", "MIO23", "MIO24", "MIO25", "MIO26", "MIO27";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO16", "MIO17", "MIO18", "MIO19", "MIO20", "MIO21";
+ bias-disable;
+ low-power-enable;
+ };
+
+ mux-mdio {
+ function = "mdio0";
+ groups = "mdio0_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio0_0_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_gpio0_default: gpio0-default {
+ mux {
+ function = "gpio0";
+ groups = "gpio0_7_grp", "gpio0_8_grp", "gpio0_9_grp",
+ "gpio0_10_grp", "gpio0_11_grp", "gpio0_12_grp",
+ "gpio0_13_grp", "gpio0_14_grp";
+ };
+
+ conf {
+ groups = "gpio0_7_grp", "gpio0_8_grp", "gpio0_9_grp",
+ "gpio0_10_grp", "gpio0_11_grp", "gpio0_12_grp",
+ "gpio0_13_grp", "gpio0_14_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-pull-up {
+ pins = "MIO9", "MIO10", "MIO11", "MIO12", "MIO13", "MIO14";
+ bias-pull-up;
+ };
+
+ conf-pull-none {
+ pins = "MIO7", "MIO8";
+ bias-disable;
+ };
+ };
+
+ pinctrl_i2c0_default: i2c0-default {
+ mux {
+ groups = "i2c0_10_grp";
+ function = "i2c0";
+ };
+
+ conf {
+ groups = "i2c0_10_grp";
+ bias-pull-up;
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+ };
+
+ pinctrl_sdhci0_default: sdhci0-default {
+ mux {
+ groups = "sdio0_2_grp";
+ function = "sdio0";
+ };
+
+ conf {
+ groups = "sdio0_2_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ bias-disable;
+ };
+
+ mux-cd {
+ groups = "gpio0_0_grp";
+ function = "sdio0_cd";
+ };
+
+ conf-cd {
+ groups = "gpio0_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ mux-wp {
+ groups = "gpio0_15_grp";
+ function = "sdio0_wp";
+ };
+
+ conf-wp {
+ groups = "gpio0_15_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+ };
+
+ pinctrl_uart1_default: uart1-default {
+ mux {
+ groups = "uart1_10_grp";
+ function = "uart1";
+ };
+
+ conf {
+ groups = "uart1_10_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-rx {
+ pins = "MIO49";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO48";
+ bias-disable = <0>;
+ };
+ };
+};
+
&sdhci0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci0_default>;
};
&uart1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
};
diff --git a/arch/arm/boot/dts/zynq-zc706.dts b/arch/arm/boot/dts/zynq-zc706.dts
index a8bbdfbc7093..1ae78766d926 100644
--- a/arch/arm/boot/dts/zynq-zc706.dts
+++ b/arch/arm/boot/dts/zynq-zc706.dts
@@ -33,15 +33,24 @@
status = "okay";
phy-mode = "rgmii-id";
phy-handle = <ðernet_phy>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem0_default>;
ethernet_phy: ethernet-phy@7 {
reg = <7>;
};
};
+&gpio0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio0_default>;
+};
+
&i2c0 {
status = "okay";
clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
i2cswitch@74 {
compatible = "nxp,pca9548";
@@ -107,10 +116,153 @@
};
};
+&pinctrl0 {
+ pinctrl_gem0_default: gem0-default {
+ mux {
+ function = "ethernet0";
+ groups = "ethernet0_0_grp";
+ };
+
+ conf {
+ groups = "ethernet0_0_grp";
+ slew-rate = <0>;
+ io-standard = <4>;
+ };
+
+ conf-rx {
+ pins = "MIO22", "MIO23", "MIO24", "MIO25", "MIO26", "MIO27";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO16", "MIO17", "MIO18", "MIO19", "MIO20", "MIO21";
+ low-power-enable;
+ bias-disable;
+ };
+
+ mux-mdio {
+ function = "mdio0";
+ groups = "mdio0_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio0_0_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_gpio0_default: gpio0-default {
+ mux {
+ function = "gpio0";
+ groups = "gpio0_7_grp", "gpio0_46_grp", "gpio0_47_grp";
+ };
+
+ conf {
+ groups = "gpio0_7_grp", "gpio0_46_grp", "gpio0_47_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-pull-up {
+ pins = "MIO46", "MIO47";
+ bias-pull-up;
+ };
+
+ conf-pull-none {
+ pins = "MIO7";
+ bias-disable;
+ };
+ };
+
+ pinctrl_i2c0_default: i2c0-default {
+ mux {
+ groups = "i2c0_10_grp";
+ function = "i2c0";
+ };
+
+ conf {
+ groups = "i2c0_10_grp";
+ bias-pull-up;
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+ };
+
+ pinctrl_sdhci0_default: sdhci0-default {
+ mux {
+ groups = "sdio0_2_grp";
+ function = "sdio0";
+ };
+
+ conf {
+ groups = "sdio0_2_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ bias-disable;
+ };
+
+ mux-cd {
+ groups = "gpio0_14_grp";
+ function = "sdio0_cd";
+ };
+
+ conf-cd {
+ groups = "gpio0_14_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ mux-wp {
+ groups = "gpio0_15_grp";
+ function = "sdio0_wp";
+ };
+
+ conf-wp {
+ groups = "gpio0_15_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+ };
+
+ pinctrl_uart1_default: uart1-default {
+ mux {
+ groups = "uart1_10_grp";
+ function = "uart1";
+ };
+
+ conf {
+ groups = "uart1_10_grp";
+ slew-rate = <0>;
+ io-standard = <1>;
+ };
+
+ conf-rx {
+ pins = "MIO49";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO48";
+ bias-disable;
+ };
+ };
+};
+
&sdhci0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci0_default>;
};
&uart1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
};
--
2.1.3.1.ge241007
next prev parent reply other threads:[~2014-11-28 1:27 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-11-28 1:26 [PATCH v2 0/7] Pinctrl support for Zynq Soren Brinkmann
2014-11-28 1:26 ` [PATCH v2 1/7] pinctrl: pinconf-generic: Infer map type from DT property Soren Brinkmann
2014-12-02 15:01 ` Linus Walleij
2014-12-03 23:04 ` Sören Brinkmann
2014-11-28 1:26 ` [PATCH v2 2/7] pinctrl: pinconf-generic: Allow driver to specify DT params Soren Brinkmann
2014-11-28 1:26 ` [PATCH v2 3/7] pinctrl: zynq: Document DT binding Soren Brinkmann
2014-11-28 1:26 ` [PATCH v2 4/7] pinctrl: Add driver for Zynq Soren Brinkmann
2014-11-28 1:26 ` [PATCH v2 5/7] ARM: zynq: Enable pinctrl Soren Brinkmann
2014-11-28 1:26 ` Soren Brinkmann [this message]
2014-11-28 1:26 ` [PATCH v2 7/7] pinctrl: qcom-spmi-gpio: Migrate to pinconf-generic Soren Brinkmann
2014-12-03 13:03 ` Ivan T. Ivanov
2014-12-03 17:38 ` Sören Brinkmann
2014-12-04 9:30 ` Ivan T. Ivanov
2014-12-04 17:21 ` Sören Brinkmann
2014-12-05 7:59 ` Ivan T. Ivanov
2014-12-05 17:08 ` Sören Brinkmann
2014-12-05 17:37 ` Sören Brinkmann
2014-12-12 16:21 ` Sören Brinkmann
2014-12-03 12:51 ` [PATCH v2 0/7] Pinctrl support for Zynq Ivan T. Ivanov
2014-12-03 17:59 ` Sören Brinkmann
2014-12-04 9:44 ` Linus Walleij
2014-12-04 17:28 ` Sören Brinkmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1417137993-8337-7-git-send-email-soren.brinkmann@xilinx.com \
--to=soren.brinkmann@xilinx.com \
--cc=b.galvani@gmail.com \
--cc=bjorn.andersson@sonymobile.com \
--cc=heiko@sntech.de \
--cc=iivanov@mm-sol.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=linux-sh@vger.kernel.org \
--cc=michal.simek@xilinx.com \
--cc=rubini@unipv.it \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®