mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Jonghwa Lee <jonghwa3.lee@samsung.com>
To: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org, sre@kernel.org, dbaryshkov@gmail.com,
	dwmw2@infradead.org, anton@enomsg.org, pavel@ucw.cz,
	myungjoo.ham@samsung.com, cw00.choi@samsung.com,
	Jonghwa Lee <jonghwa3.lee@samsung.com>
Subject: [PATCH V3 08/11] power: charger-manager: Make chraging decision focusing on battery status.
Date: Fri, 19 Dec 2014 17:55:20 +0900	[thread overview]
Message-ID: <1418979323-7188-9-git-send-email-jonghwa3.lee@samsung.com> (raw)
In-Reply-To: <1418979323-7188-1-git-send-email-jonghwa3.lee@samsung.com>

In cm_monitor() where charging management starts, it checks various charging
condition sequentially to decide next charging operation. However, as it
follows sequential process, cascaded IF statements, it does some duplicated
jobs which is already done in previous stage. It results delay in decision
making. And moreover, starting point of charing is spreaded all around, so
it makes maintain codes and debugging difficult.

Both of problems mentioned above becomes clean if it manages battery charging
focusing on battery status not following sequential condition checking.
Now, cm_monitor() moves battery state diagram and does optimal operation for
current state. As a result, it reduces whole monitoring time almost in half.

Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
---
 drivers/power/charger-manager.c       |  177 +++++++++++----------------------
 include/linux/power/charger-manager.h |    3 +
 2 files changed, 62 insertions(+), 118 deletions(-)

diff --git a/drivers/power/charger-manager.c b/drivers/power/charger-manager.c
index dc15436..44cc19a 100644
--- a/drivers/power/charger-manager.c
+++ b/drivers/power/charger-manager.c
@@ -249,6 +249,19 @@ static bool is_full_charged(struct charger_manager *cm)
 	if (!fuel_gauge)
 		return false;
 
+	/* Full, if it's over the fullbatt voltage */
+	if (desc->fullbatt_uV > 0) {
+		ret = get_batt_uV(cm, &uV);
+		if (!ret) {
+			/* Battery is already full, checks voltage drop. */
+			if (cm->battery_status == POWER_SUPPLY_STATUS_FULL
+					&& desc->fullbatt_vchkdrop_uV)
+				uV += desc->fullbatt_vchkdrop_uV;
+			if (uV >= desc->fullbatt_uV)
+				return true;
+		}
+	}
+
 	if (desc->fullbatt_full_capacity > 0) {
 		val.intval = 0;
 
@@ -259,13 +272,6 @@ static bool is_full_charged(struct charger_manager *cm)
 			return true;
 	}
 
-	/* Full, if it's over the fullbatt voltage */
-	if (desc->fullbatt_uV > 0) {
-		ret = get_batt_uV(cm, &uV);
-		if (!ret && uV >= desc->fullbatt_uV)
-			return true;
-	}
-
 	/* Full, if the capacity is more than fullbatt_soc */
 	if (desc->fullbatt_soc > 0) {
 		val.intval = 0;
@@ -376,67 +382,13 @@ static int try_charger_enable(struct charger_manager *cm, bool enable)
 		}
 	}
 
-	if (!err) {
+	if (!err)
 		cm->charger_enabled = enable;
-		power_supply_changed(&cm->charger_psy);
-	}
 
 	return err;
 }
 
 /**
- * try_charger_restart - Restart charging.
- * @cm: the Charger Manager representing the battery.
- *
- * Restart charging by turning off and on the charger.
- */
-static int try_charger_restart(struct charger_manager *cm)
-{
-	int err;
-
-	if (cm->emergency_stop)
-		return -EAGAIN;
-
-	err = try_charger_enable(cm, false);
-	if (err)
-		return err;
-
-	return try_charger_enable(cm, true);
-}
-
-/**
- * fullbatt_vchk - Check voltage drop some times after "FULL" event.
- *
- * If a user has designated "fullbatt_vchkdrop_uV" values with
- * charger_desc, Charger Manager checks voltage drop after the battery
- * "FULL" event. It checks whether the voltage has dropped more than
- * fullbatt_vchkdrop_uV by calling this function after fullbatt_vchkrop_ms.
- */
-static void fullbatt_vchk(struct charger_manager *cm)
-{
-	struct charger_desc *desc = cm->desc;
-	int batt_uV, err, diff;
-
-	if (!desc->fullbatt_vchkdrop_uV)
-		return;
-
-	err = get_batt_uV(cm, &batt_uV);
-	if (err) {
-		dev_err(cm->dev, "%s: get_batt_uV error(%d)\n", __func__, err);
-		return;
-	}
-
-	diff = desc->fullbatt_uV - batt_uV;
-	if (diff < 0)
-		return;
-
-	dev_info(cm->dev, "VBATT dropped %duV after full-batt\n", diff);
-
-	if (diff > desc->fullbatt_vchkdrop_uV)
-		try_charger_restart(cm);
-}
-
-/**
  * check_charging_duration - Monitor charging/discharging duration
  * @cm: the Charger Manager representing the battery.
  *
@@ -463,17 +415,14 @@ static int check_charging_duration(struct charger_manager *cm)
 		if (duration > desc->charging_max_duration_ms) {
 			dev_info(cm->dev, "Charging duration exceed %ums\n",
 				 desc->charging_max_duration_ms);
-			try_charger_enable(cm, false);
 			ret = true;
 		}
-	} else if (is_ext_pwr_online(cm) && !cm->charger_enabled) {
+	} else if (cm->battery_status == POWER_SUPPLY_STATUS_NOT_CHARGING) {
 		duration = curr - cm->charging_end_time;
 
-		if (duration > desc->charging_max_duration_ms &&
-				is_ext_pwr_online(cm)) {
+		if (duration > desc->charging_max_duration_ms) {
 			dev_info(cm->dev, "Discharging duration exceed %ums\n",
 				 desc->discharging_max_duration_ms);
-			try_charger_enable(cm, true);
 			ret = true;
 		}
 	}
@@ -527,10 +476,45 @@ static int cm_check_thermal_status(struct charger_manager *cm)
 	else if (temp < lower_limit)
 		ret = CM_EVENT_BATT_COLD;
 
+	cm->emergency_stop = ret;
+
 	return ret;
 }
 
 /**
+ * cm_get_target_status - Check current status and get next target status.
+ * @cm: the Charger Manager representing the battery.
+ */
+static int cm_get_target_status(struct charger_manager *cm)
+{
+	if (!is_ext_pwr_online(cm))
+		return POWER_SUPPLY_STATUS_DISCHARGING;
+
+	if (cm_check_thermal_status(cm)) {
+		/* Check if discharging duration exeeds limit. */
+		if (check_charging_duration(cm))
+			goto charging_ok;
+		return POWER_SUPPLY_STATUS_NOT_CHARGING;
+	}
+
+	switch (cm->battery_status) {
+	case POWER_SUPPLY_STATUS_CHARGING:
+		/* Check if charging duration exeeds limit. */
+		if (check_charging_duration(cm))
+			return POWER_SUPPLY_STATUS_FULL;
+	case POWER_SUPPLY_STATUS_FULL:
+		if (is_full_charged(cm))
+			return POWER_SUPPLY_STATUS_FULL;
+	default:
+		break;
+	}
+
+charging_ok:
+	/* Charging is allowed. */
+	return POWER_SUPPLY_STATUS_CHARGING;
+}
+
+/**
  * _cm_monitor - Monitor the temperature and return true for exceptions.
  * @cm: the Charger Manager representing the battery.
  *
@@ -539,56 +523,18 @@ static int cm_check_thermal_status(struct charger_manager *cm)
  */
 static bool _cm_monitor(struct charger_manager *cm)
 {
-	int temp_alrt;
+	int target;
 
-	temp_alrt = cm_check_thermal_status(cm);
+	target = cm_get_target_status(cm);
 
-	/* It has been stopped already */
-	if (temp_alrt && cm->emergency_stop)
-		return false;
-
-	/*
-	 * Check temperature whether overheat or cold.
-	 * If temperature is out of range normal state, stop charging.
-	 */
-	if (temp_alrt) {
-		cm->emergency_stop = temp_alrt;
-		try_charger_enable(cm, false);
-
-	/*
-	 * Check whole charging duration and discharing duration
-	 * after full-batt.
-	 */
-	} else if (!cm->emergency_stop && check_charging_duration(cm)) {
-		dev_dbg(cm->dev,
-			"Charging/Discharging duration is out of range\n");
-	/*
-	 * Check dropped voltage of battery. If battery voltage is more
-	 * dropped than fullbatt_vchkdrop_uV after fully charged state,
-	 * charger-manager have to recharge battery.
-	 */
-	} else if (!cm->emergency_stop && is_ext_pwr_online(cm) &&
-			!cm->charger_enabled) {
-		fullbatt_vchk(cm);
+	try_charger_enable(cm, (target == POWER_SUPPLY_STATUS_CHARGING));
 
-	/*
-	 * Check whether fully charged state to protect overcharge
-	 * if charger-manager is charging for battery.
-	 */
-	} else if (!cm->emergency_stop && is_full_charged(cm) &&
-			cm->charger_enabled) {
-		dev_info(cm->dev, "EVENT_HANDLE: Battery Fully Charged\n");
-		try_charger_enable(cm, false);
-
-		fullbatt_vchk(cm);
-	} else {
-		cm->emergency_stop = 0;
-		if (is_ext_pwr_online(cm)) {
-			try_charger_enable(cm, true);
-		}
+	if (cm->battery_status != target) {
+		cm->battery_status = target;
+		power_supply_changed(&cm->charger_psy);
 	}
 
-	return true;
+	return (cm->battery_status == POWER_SUPPLY_STATUS_NOT_CHARGING);
 }
 
 /**
@@ -694,12 +640,7 @@ static int charger_get_property(struct power_supply *psy,
 
 	switch (psp) {
 	case POWER_SUPPLY_PROP_STATUS:
-		if (is_charging(cm))
-			val->intval = POWER_SUPPLY_STATUS_CHARGING;
-		else if (is_ext_pwr_online(cm))
-			val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
-		else
-			val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+		val->intval = cm->battery_status;
 		break;
 	case POWER_SUPPLY_PROP_HEALTH:
 		if (cm->emergency_stop > 0)
diff --git a/include/linux/power/charger-manager.h b/include/linux/power/charger-manager.h
index 22a8097..37fb181 100644
--- a/include/linux/power/charger-manager.h
+++ b/include/linux/power/charger-manager.h
@@ -220,6 +220,7 @@ struct charger_desc {
  *	saved status of battery before entering suspend-to-RAM
  * @charging_start_time: saved start time of enabling charging
  * @charging_end_time: saved end time of disabling charging
+ * @battery_status: Current battery status
  */
 struct charger_manager {
 	struct list_head entry;
@@ -237,6 +238,8 @@ struct charger_manager {
 
 	u64 charging_start_time;
 	u64 charging_end_time;
+
+	int battery_status;
 };
 
 #endif /* _CHARGER_MANAGER_H */
-- 
1.7.9.5


  parent reply	other threads:[~2014-12-19  8:56 UTC|newest]

Thread overview: 19+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-12-19  8:55 [PATCH V3 0/11] Improve charger manager driver for optimized operation Jonghwa Lee
2014-12-19  8:55 ` [PATCH V3 01/11] power: charger-manager: Use alarmtimer for battery monitoring in suspend Jonghwa Lee
2014-12-20  0:21   ` Pavel Machek
2015-01-21 20:44   ` Sebastian Reichel
2014-12-19  8:55 ` [PATCH V3 02/11] power: charger-manager: Use thermal subsystem interface only to get temperature Jonghwa Lee
2015-01-21 22:38   ` Sebastian Reichel
2014-12-19  8:55 ` [PATCH V3 03/11] power: charger-manager: Use power_supply_changed() not private uevent Jonghwa Lee
2014-12-19  8:55 ` [PATCH V3 04/11] power: charger-manager: Remove deprecated function, cm_notify_event() Jonghwa Lee
2014-12-19  8:55 ` [PATCH V3 05/11] power: charger-manager: Fix to use CHARGE_NOW/FULL property correctly Jonghwa Lee
2014-12-19  8:55 ` [PATCH V3 06/11] power: charger-manager: Concentrate scattered power_supply_changed() calls Jonghwa Lee
2014-12-19  8:55 ` [PATCH V3 07/11] power: charger-manager: Get external power souce information only from EXTCON Jonghwa Lee
2014-12-19  8:55 ` Jonghwa Lee [this message]
2014-12-20  0:24   ` [PATCH V3 08/11] power: charger-manager: Make chraging decision focusing on battery status Pavel Machek
2014-12-22  2:10     ` jonghwa3.lee
2014-12-19  8:55 ` [PATCH V3 09/11] power: charger-manager: Not to start charging directly in cable nofitication Jonghwa Lee
2014-12-19  8:55 ` [PATCH V3 10/11] power: charger-manager: Support different polling mode for sleep state Jonghwa Lee
2014-12-19  8:55 ` [PATCH V3 11/11] power: charger-manager: Support to change polling rate in runtime Jonghwa Lee
2014-12-20  0:29   ` Pavel Machek
2014-12-22  1:57     ` jonghwa3.lee

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1418979323-7188-9-git-send-email-jonghwa3.lee@samsung.com \
    --to=jonghwa3.lee@samsung.com \
    --cc=anton@enomsg.org \
    --cc=cw00.choi@samsung.com \
    --cc=dbaryshkov@gmail.com \
    --cc=dwmw2@infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pm@vger.kernel.org \
    --cc=myungjoo.ham@samsung.com \
    --cc=pavel@ucw.cz \
    --cc=sre@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®