From: <tthayer@opensource.altera.com>
To: <bp@alien8.de>, <dougthompson@xmission.com>,
<m.chehab@samsung.com>, <robh+dt@kernel.org>,
<pawel.moll@arm.com>, <mark.rutland@arm.com>,
<ijc+devicetree@hellion.org.uk>, <galak@codeaurora.org>,
<linux@arm.linux.org.uk>, <dinguyen@opensource.altera.com>,
<grant.likely@linaro.org>
Cc: <devicetree@vger.kernel.org>, <linux-doc@vger.kernel.org>,
<linux-edac@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>, <tthayer.linux@gmail.com>,
<tthayer@opensource.altera.com>
Subject: [PATCHv6 5/5] arm: dts: Add Altera L2 Cache and OCRAM EDAC entries
Date: Thu, 8 Jan 2015 20:53:56 -0600 [thread overview]
Message-ID: <1420772036-3112-6-git-send-email-tthayer@opensource.altera.com> (raw)
In-Reply-To: <1420772036-3112-1-git-send-email-tthayer@opensource.altera.com>
From: Thor Thayer <tthayer@opensource.altera.com>
Adding the device tree entries and bindings needed to support
the Altera L2 cache and On-Chip RAM EDAC. This patch relies upon
an earlier patch to declare and setup On-chip RAM properly.
http://www.spinics.net/lists/devicetree/msg51117.html
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
---
v2: Remove OCRAM declaration and reference prior patch.
v3-5: No Change
v6: Change to nested EDAC device nodes based on community
feedback. Remove L2 syscon. Use consolidated binding.
---
.../bindings/arm/altera/socfpga-edac.txt | 46 ++++++++++++++++++++
arch/arm/boot/dts/socfpga.dtsi | 20 +++++++++
2 files changed, 66 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/altera/socfpga-edac.txt
diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-edac.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-edac.txt
new file mode 100644
index 0000000..4bf32e1
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/altera/socfpga-edac.txt
@@ -0,0 +1,46 @@
+Altera SoCFPGA Error Detection and Correction [EDAC]
+
+Required Properties:
+- compatible : Should be "altr,edac"
+- #address-cells: must be 1
+- #size-cells: must be 1
+- ranges : standard definition, should translate from local addresses
+
+Subcomponents:
+
+L2 Cache ECC
+Required Properties:
+- compatible : Should be "altr,l2-edac"
+- reg : Address and size for ECC error interrupt clear registers.
+- interrupts : Should be single bit error interrupt, then double bit error
+ interrupt. Note the rising edge type.
+
+On Chip RAM ECC
+Required Properties:
+- compatible : Should be "altr,ocram-edac"
+- reg : Address and size for ECC error interrupt clear registers.
+- iram : phandle to On-Chip RAM definition.
+- interrupts : Should be single bit error interrupt, then double bit error
+ interrupt. Note the rising edge type.
+
+Example:
+
+ soc_ecc {
+ compatible = "altr,edac";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ l2edac@ffd08140 {
+ compatible = "altr,l2-edac";
+ reg = <0xffd08140 0x4>;
+ interrupts = <0 36 1>, <0 37 1>;
+ };
+
+ ocramedac@ffd08144 {
+ compatible = "altr,ocram-edac";
+ reg = <0xffd08144 0x4>;
+ iram = <&ocram>;
+ interrupts = <0 178 1>, <0 179 1>;
+ };
+ };
diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi
index 252c3d1..e546e47 100644
--- a/arch/arm/boot/dts/socfpga.dtsi
+++ b/arch/arm/boot/dts/socfpga.dtsi
@@ -618,6 +618,26 @@
interrupts = <0 39 4>;
};
+ soc_ecc {
+ compatible = "altr,edac";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ l2edac@ffd08140 {
+ compatible = "altr,l2-edac";
+ reg = <0xffd08140 0x4>;
+ interrupts = <0 36 1>, <0 37 1>;
+ };
+
+ ocramedac@ffd08144 {
+ compatible = "altr,ocram-edac";
+ reg = <0xffd08144 0x4>;
+ iram = <&ocram>;
+ interrupts = <0 178 1>, <0 179 1>;
+ };
+ };
+
L2: l2-cache@fffef000 {
compatible = "arm,pl310-cache";
reg = <0xfffef000 0x1000>;
--
1.7.9.5
next prev parent reply other threads:[~2015-01-09 3:11 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-01-09 2:53 [PATCHv6 0/5] Add Altera peripheral memories to EDAC framework tthayer
2015-01-09 2:53 ` [PATCHv6 1/5] arm: socfpga: Enable L2 Cache ECC on startup tthayer
2015-02-06 18:52 ` Mark Rutland
2015-01-09 2:53 ` [PATCHv6 2/5] arm: socfpga: Enable OCRAM " tthayer
2015-02-06 18:45 ` Mark Rutland
2015-02-06 22:05 ` Thor Thayer
2015-01-09 2:53 ` [PATCHv6 3/5] edac: altera: Remove SDRAM module compile tthayer
2015-01-09 2:53 ` [PATCHv6 4/5] edac: altera: Add Altera L2 Cache and OCRAM EDAC Support tthayer
2015-02-06 19:17 ` Mark Rutland
2015-02-06 22:09 ` Thor Thayer
2015-02-07 10:02 ` Russell King - ARM Linux
2015-01-09 2:53 ` tthayer [this message]
2015-02-06 17:03 ` [RESEND PATCHv6 5/5] arm: dts: Add Altera L2 Cache and OCRAM EDAC entries Thor Thayer
2015-02-06 19:24 ` [PATCHv6 " Mark Rutland
2015-02-06 22:04 ` Thor Thayer
2015-01-29 20:53 ` [PATCHv6 0/5] Add Altera peripheral memories to EDAC framework Thor Thayer
2015-02-06 19:29 ` Mark Rutland
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1420772036-3112-6-git-send-email-tthayer@opensource.altera.com \
--to=tthayer@opensource.altera.com \
--cc=bp@alien8.de \
--cc=devicetree@vger.kernel.org \
--cc=dinguyen@opensource.altera.com \
--cc=dougthompson@xmission.com \
--cc=galak@codeaurora.org \
--cc=grant.likely@linaro.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-edac@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
--cc=m.chehab@samsung.com \
--cc=mark.rutland@arm.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
--cc=tthayer.linux@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®