From: Maxime Ripard <maxime.ripard@free-electrons.com>
To: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org,
Nicolas Ferre <nicolas.ferre@atmel.com>,
Alexandre Belloni <alexandre.belloni@free-electrons.com>,
Ludovic Desroches <ludovic.desroches@atmel.com>,
Thomas Petazzoni <thomas@free-electrons.com>,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
Maxime Ripard <maxime.ripard@free-electrons.com>
Subject: [PATCH 2/2] dmaengine: hdmac: Implement interleaved transfers
Date: Wed, 27 May 2015 16:01:53 +0200 [thread overview]
Message-ID: <1432735313-481-3-git-send-email-maxime.ripard@free-electrons.com> (raw)
In-Reply-To: <1432735313-481-1-git-send-email-maxime.ripard@free-electrons.com>
The AT91 HDMAC controller supports interleaved transfers through what's
called the Picture-in-Picture mode, which allows to transfer a squared
portion of a framebuffer.
This means that this interleaved transfer only supports interleaved
transfers which have a transfer size and ICGs that are fixed across all the
chunks.
While this is a quite drastic restriction of the interleaved transfers
compared to what the dmaengine API allows, this is still useful, and our
driver will only reject transfers that do not conform to this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/dma/at_hdmac.c | 106 ++++++++++++++++++++++++++++++++++++++++++++
drivers/dma/at_hdmac_regs.h | 5 +++
2 files changed, 111 insertions(+)
diff --git a/drivers/dma/at_hdmac.c b/drivers/dma/at_hdmac.c
index 57b2141ddddc..59892126d175 100644
--- a/drivers/dma/at_hdmac.c
+++ b/drivers/dma/at_hdmac.c
@@ -247,6 +247,10 @@ static void atc_dostart(struct at_dma_chan *atchan, struct at_desc *first)
channel_writel(atchan, CTRLA, 0);
channel_writel(atchan, CTRLB, 0);
channel_writel(atchan, DSCR, first->txd.phys);
+ channel_writel(atchan, SPIP, ATC_SPIP_HOLE(first->src_hole) |
+ ATC_SPIP_BOUNDARY(first->boundary));
+ channel_writel(atchan, DPIP, ATC_DPIP_HOLE(first->dst_hole) |
+ ATC_DPIP_BOUNDARY(first->boundary));
dma_writel(atdma, CHER, atchan->mask);
vdbg_dump_regs(atchan);
@@ -635,6 +639,104 @@ static dma_cookie_t atc_tx_submit(struct dma_async_tx_descriptor *tx)
}
/**
+ * atc_prep_dma_interleaved - prepare memory to memory interleaved operation
+ * @chan: the channel to prepare operation on
+ * @xt: Interleaved transfer template
+ * @flags: tx descriptor status flags
+ */
+static struct dma_async_tx_descriptor *
+atc_prep_dma_interleaved(struct dma_chan *chan,
+ struct dma_interleaved_template *xt,
+ unsigned long flags)
+{
+ struct at_dma_chan *atchan = to_at_dma_chan(chan);
+ struct data_chunk *first = xt->sgl;
+ struct at_desc *desc = NULL;
+ size_t xfer_count;
+ unsigned int dwidth;
+ u32 ctrla;
+ u32 ctrlb;
+ size_t len = 0;
+ int i;
+
+ dev_info(chan2dev(chan),
+ "%s: src=0x%08x, dest=0x%08x, numf=%d, frame_size=%d, flags=0x%lx\n",
+ __func__, xt->src_start, xt->dst_start, xt->numf,
+ xt->frame_size, flags);
+
+ if (unlikely(!xt || xt->numf != 1 || !xt->frame_size))
+ return NULL;
+
+ /*
+ * The controller can only "skip" X bytes every Y bytes, so we
+ * need to make sure we are given a template that fit that
+ * description, ie a template with chunks that always have the
+ * same size, with the same ICGs.
+ */
+ for (i = 0; i < xt->frame_size; i++) {
+ struct data_chunk *chunk = xt->sgl + i;
+
+ if ((chunk->size != xt->sgl->size) ||
+ (dmaengine_get_dst_icg(xt, chunk) != dmaengine_get_dst_icg(xt, first)) ||
+ (dmaengine_get_src_icg(xt, chunk) != dmaengine_get_src_icg(xt, first))) {
+ dev_err(chan2dev(chan),
+ "%s: the controller can transfer only identical chunks\n",
+ __func__);
+ return NULL;
+ }
+
+ len += chunk->size;
+ }
+
+ dwidth = atc_get_xfer_width(xt->src_start,
+ xt->dst_start, len);
+
+ xfer_count = len >> dwidth;
+ if (xfer_count > ATC_BTSIZE_MAX) {
+ dev_err(chan2dev(chan), "%s: buffer is too big\n", __func__);
+ return NULL;
+ }
+
+ ctrla = ATC_SRC_WIDTH(dwidth) |
+ ATC_DST_WIDTH(dwidth);
+
+ ctrlb = ATC_DEFAULT_CTRLB | ATC_IEN
+ | ATC_SRC_ADDR_MODE_INCR
+ | ATC_DST_ADDR_MODE_INCR
+ | ATC_SRC_PIP
+ | ATC_DST_PIP
+ | ATC_FC_MEM2MEM;
+
+ /* create the transfer */
+ desc = atc_desc_get(atchan);
+ if (!desc) {
+ dev_err(chan2dev(chan),
+ "%s: couldn't allocate our descriptor\n", __func__);
+ return NULL;
+ }
+
+ desc->lli.saddr = xt->src_start;
+ desc->lli.daddr = xt->dst_start;
+ desc->lli.ctrla = ctrla | xfer_count;
+ desc->lli.ctrlb = ctrlb;
+
+ desc->boundary = first->size >> dwidth;
+ desc->dst_hole = (dmaengine_get_dst_icg(xt, first) >> dwidth) + 1;
+ desc->src_hole = (dmaengine_get_src_icg(xt, first) >> dwidth) + 1;
+
+ desc->txd.cookie = -EBUSY;
+ desc->total_len = desc->len = len;
+ desc->tx_width = dwidth;
+
+ /* set end-of-link to the last link descriptor of list*/
+ set_desc_eol(desc);
+
+ desc->txd.flags = flags; /* client is in control of this ack */
+
+ return &desc->txd;
+}
+
+/**
* atc_prep_dma_memcpy - prepare a memcpy operation
* @chan: the channel to prepare operation on
* @dest: operation virtual destination address
@@ -1609,6 +1711,7 @@ static int __init at_dma_probe(struct platform_device *pdev)
/* setup platform data for each SoC */
dma_cap_set(DMA_MEMCPY, at91sam9rl_config.cap_mask);
dma_cap_set(DMA_SG, at91sam9rl_config.cap_mask);
+ dma_cap_set(DMA_INTERLEAVE, at91sam9g45_config.cap_mask);
dma_cap_set(DMA_MEMCPY, at91sam9g45_config.cap_mask);
dma_cap_set(DMA_SLAVE, at91sam9g45_config.cap_mask);
dma_cap_set(DMA_SG, at91sam9g45_config.cap_mask);
@@ -1713,6 +1816,9 @@ static int __init at_dma_probe(struct platform_device *pdev)
atdma->dma_common.dev = &pdev->dev;
/* set prep routines based on capability */
+ if (dma_has_cap(DMA_INTERLEAVE, atdma->dma_common.cap_mask))
+ atdma->dma_common.device_prep_interleaved_dma = atc_prep_dma_interleaved;
+
if (dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask))
atdma->dma_common.device_prep_dma_memcpy = atc_prep_dma_memcpy;
diff --git a/drivers/dma/at_hdmac_regs.h b/drivers/dma/at_hdmac_regs.h
index 2727ca560572..bc8d5ebedd19 100644
--- a/drivers/dma/at_hdmac_regs.h
+++ b/drivers/dma/at_hdmac_regs.h
@@ -196,6 +196,11 @@ struct at_desc {
size_t len;
u32 tx_width;
size_t total_len;
+
+ /* Interleaved data */
+ size_t boundary;
+ size_t dst_hole;
+ size_t src_hole;
};
static inline struct at_desc *
--
2.4.1
next prev parent reply other threads:[~2015-05-27 14:05 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-05-27 14:01 [PATCH 0/2] dmaengine: hdmac: Implement interleaved transfers support Maxime Ripard
2015-05-27 14:01 ` [PATCH 1/2] dmaengine: Move icg helpers to global header Maxime Ripard
2015-06-01 8:14 ` Ludovic Desroches
2015-05-27 14:01 ` Maxime Ripard [this message]
2015-06-01 8:32 ` [PATCH 2/2] dmaengine: hdmac: Implement interleaved transfers Ludovic Desroches
2015-06-02 9:19 ` Maxime Ripard
2015-06-12 12:44 ` [PATCH 0/2] dmaengine: hdmac: Implement interleaved transfers support Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1432735313-481-3-git-send-email-maxime.ripard@free-electrons.com \
--to=maxime.ripard@free-electrons.com \
--cc=alexandre.belloni@free-electrons.com \
--cc=dmaengine@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=ludovic.desroches@atmel.com \
--cc=nicolas.ferre@atmel.com \
--cc=thomas@free-electrons.com \
--cc=vinod.koul@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®