From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1753815AbbG0NKu (ORCPT ); Mon, 27 Jul 2015 09:10:50 -0400 Received: from comal.ext.ti.com ([198.47.26.152]:50266 "EHLO comal.ext.ti.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1753689AbbG0NKc (ORCPT ); Mon, 27 Jul 2015 09:10:32 -0400 From: Roger Quadros To: , , CC: , , , , Roger Quadros Subject: [PATCH v2 2/2] ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2 Date: Mon, 27 Jul 2015 16:10:17 +0300 Message-ID: <1438002617-15152-3-git-send-email-rogerq@ti.com> X-Mailer: git-send-email 2.1.4 In-Reply-To: <1438002617-15152-1-git-send-email-rogerq@ti.com> References: <1438002617-15152-1-git-send-email-rogerq@ti.com> MIME-Version: 1.0 Content-Type: text/plain Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org The VBUS line of USB2 is connected to VBUS detect logic on the PMIC. Use the palmas-usb driver to report VBUS events to the USB driver. As the palmas-usb driver supports GPIO based ID reporting provide the GPIO for ID pin as well. Signed-off-by: Roger Quadros --- arch/arm/boot/dts/am57xx-beagle-x15.dts | 29 ++++++++++++++++------------- 1 file changed, 16 insertions(+), 13 deletions(-) diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index a63bf78..f32cf20 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -98,13 +98,6 @@ pinctrl-0 = <&extcon_usb1_pins>; }; - extcon_usb2: extcon_usb2 { - compatible = "linux,extcon-usb-gpio"; - id-gpio = <&gpio7 24 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&extcon_usb2_pins>; - }; - hdmi0: connector { compatible = "hdmi-connector"; label = "hdmi"; @@ -326,12 +319,6 @@ >; }; - extcon_usb2_pins: extcon_usb2_pins { - pinctrl-single,pins = < - 0x3e8 (PIN_INPUT_PULLUP | MUX_MODE14) /* uart1_ctsn.gpio7_24 */ - >; - }; - tpd12s015_pins: pinmux_tpd12s015_pins { pinctrl-single,pins = < 0x3b0 (PIN_OUTPUT | MUX_MODE14) /* gpio7_10 CT_CP_HPD */ @@ -495,6 +482,14 @@ gpio-controller; #gpio-cells = <2>; }; + + extcon_usb2: tps659038_usb { + compatible = "ti,palmas-usb-vid"; + ti,enable-vbus-detection; + ti,enable-id-detection; + id-gpios = <&gpio7 24 GPIO_ACTIVE_HIGH>; + }; + }; tmp102: tmp102@48 { @@ -624,6 +619,14 @@ }; &usb2 { + /* + * Stand alone usage is peripheral only. + * However, with some resistor modifications + * this port can be used via expansion connectors + * as "host" or "dual-role". If so, provide + * the necessary dr_mode override in the expansion + * board's DT. + */ dr_mode = "peripheral"; }; -- 2.1.4