[PATCH 3/6] iio: mma8452: add freefall / motion interrupt source

[Martin Kepplinger <martink@posteo.de>]

This adds the freefall / motion interrupt source definitions to the driver.
It is used in this series' next patch, for chips that don't support the
transient interrupt source.

Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
---
 drivers/iio/accel/mma8452.c | 44 ++++++++++++++++++++++++++++++++++++--------
 1 file changed, 36 insertions(+), 8 deletions(-)

diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
index 7b2ab17..6b1a862 100644
--- a/drivers/iio/accel/mma8452.c
+++ b/drivers/iio/accel/mma8452.c
@@ -42,6 +42,16 @@
 #define  MMA8452_DATA_CFG_HPF_MASK		BIT(4)
 #define MMA8452_HP_FILTER_CUTOFF		0x0f
 #define  MMA8452_HP_FILTER_CUTOFF_SEL_MASK	GENMASK(1, 0)
+#define MMA8452_FF_MT_CFG			0x15
+#define  MMA8452_FF_MT_CFG_OAE			BIT(6)
+#define  MMA8452_FF_MT_CFG_ELE			BIT(7)
+#define MMA8452_FF_MT_SRC			0x16
+#define  MMA8452_FF_MT_SRC_XHE			BIT(1)
+#define  MMA8452_FF_MT_SRC_YHE			BIT(3)
+#define  MMA8452_FF_MT_SRC_ZHE			BIT(5)
+#define MMA8452_FF_MT_THS			0x17
+#define  MMA8452_FF_MT_THS_MASK			0x7f
+#define MMA8452_FF_MT_COUNT			0x18
 #define MMA8452_TRANSIENT_CFG			0x1d
 #define  MMA8452_TRANSIENT_CFG_HPF_BYP		BIT(0)
 #define  MMA8452_TRANSIENT_CFG_CHAN(chan)	BIT(chan + 1)
@@ -69,6 +79,7 @@
 #define MMA8452_MAX_REG				0x31
 
 #define  MMA8452_INT_DRDY			BIT(0)
+#define  MMA8452_INT_FF_MT			BIT(2)
 #define  MMA8452_INT_TRANS			BIT(5)
 
 #define  MMA8452_DEVICE_ID			0x2a
@@ -613,7 +624,8 @@ static int mma8452_write_event_config(struct iio_dev *indio_dev,
 	else
 		val &= ~BIT(chan->scan_index + chip->ev_cfg_chan_shift);
 
-	val |= MMA8452_TRANSIENT_CFG_ELE;
+	val |= chip->ev_cfg_ele;
+	val |= MMA8452_FF_MT_CFG_OAE;
 
 	return mma8452_change_config(data, chip->ev_cfg, val);
 }
@@ -654,6 +666,7 @@ static irqreturn_t mma8452_interrupt(int irq, void *p)
 {
 	struct iio_dev *indio_dev = p;
 	struct mma8452_data *data = iio_priv(indio_dev);
+	const struct mma_chip_info *chip = data->chip_info;
 	int ret = IRQ_NONE;
 	int src;
 
@@ -666,7 +679,10 @@ static irqreturn_t mma8452_interrupt(int irq, void *p)
 		ret = IRQ_HANDLED;
 	}
 
-	if (src & MMA8452_INT_TRANS) {
+	if ((src & MMA8452_INT_TRANS &&
+	     chip->ev_src == MMA8452_TRANSIENT_SRC) ||
+	    (src & MMA8452_INT_FF_MT &&
+	     chip->ev_src == MMA8452_FF_MT_SRC)) {
 		mma8452_transient_interrupt(indio_dev);
 		ret = IRQ_HANDLED;
 	}
@@ -728,6 +744,16 @@ static const struct iio_event_spec mma8452_transient_event[] = {
 	},
 };
 
+static const struct iio_event_spec mma8452_motion_event[] = {
+	{
+		.type = IIO_EV_TYPE_MAG,
+		.dir = IIO_EV_DIR_RISING,
+		.mask_separate = BIT(IIO_EV_INFO_ENABLE),
+		.mask_shared_by_type = BIT(IIO_EV_INFO_VALUE) |
+					BIT(IIO_EV_INFO_PERIOD)
+	},
+};
+
 /*
  * Threshold is configured in fixed 8G/127 steps regardless of
  * currently selected scale for measurement.
@@ -1013,13 +1039,15 @@ static int mma8452_probe(struct i2c_client *client,
 
 	if (client->irq) {
 		/*
-		 * Although we enable the transient interrupt source once and
-		 * for all here the transient event detection itself is not
-		 * enabled until userspace asks for it by
-		 * mma8452_write_event_config()
+		 * Although we enable the interrupt sources once and for
+		 * all here the event detection itself is not enabled until
+		 * userspace asks for it by mma8452_write_event_config()
 		 */
-		int supported_interrupts = MMA8452_INT_DRDY | MMA8452_INT_TRANS;
-		int enabled_interrupts = MMA8452_INT_TRANS;
+		int supported_interrupts = MMA8452_INT_DRDY |
+					   MMA8452_INT_TRANS |
+					   MMA8452_INT_FF_MT;
+		int enabled_interrupts = MMA8452_INT_TRANS |
+					 MMA8452_INT_FF_MT;
 
 		/* Assume wired to INT1 pin */
 		ret = i2c_smbus_write_byte_data(client,
-- 
2.1.4