From: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
To: <cw00.choi@samsung.com>, <lee.jones@linaro.org>
Cc: <robh+dt@kernel.org>, <pawel.moll@arm.com>,
<mark.rutland@arm.com>, <ijc+devicetree@hellion.org.uk>,
<galak@codeaurora.org>, <myungjoo.ham@samsung.com>,
<sameo@linux.intel.com>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>
Subject: [PATCH 6/6] mfd: arizona: Update DT binding documentation for jack detection
Date: Wed, 16 Sep 2015 10:56:44 +0100 [thread overview]
Message-ID: <1442397404-7579-7-git-send-email-ckeepax@opensource.wolfsonmicro.com> (raw)
In-Reply-To: <1442397404-7579-1-git-send-email-ckeepax@opensource.wolfsonmicro.com>
Add additional bindings for both inverting the polarity of the jack
detection pins and allowing the use of a second jack detection pin. Note
that the second jack detection pin is hard wired in the chip so can only
be enabled through the binding, rather than a pin being specified.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
---
Documentation/devicetree/bindings/mfd/arizona.txt | 6 ++++++
1 files changed, 6 insertions(+), 0 deletions(-)
diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt
index b98a11b..cb3a652 100644
--- a/Documentation/devicetree/bindings/mfd/arizona.txt
+++ b/Documentation/devicetree/bindings/mfd/arizona.txt
@@ -73,6 +73,12 @@ Optional properties:
If this node is not mentioned or if the value is unknown, then
headphone detection mode is set to HPDETL.
+ - wlf,use-jd-gpio : Use GPIO input along with JD1 for dual pin jack
+ detection.
+ - wlf,use-jd-gpio-nopull : Internal pull on GPIO is disabled when used for
+ jack detection.
+ - wlf,jd-invert : Invert the polarity of the jack detection switch
+
- wlf,micd-software-compare : Use a software comparison to determine mic
presence
- wlf,micd-detect-debounce : Additional software microphone detection
--
1.7.2.5
next prev parent reply other threads:[~2015-09-16 10:20 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-16 9:56 [PATCH 0/6] Arizona Extcon Update Device Bindings Charles Keepax
2015-09-16 9:56 ` [PATCH 1/6] extcon: arizona: Add device binding to enable ADC mode micdet Charles Keepax
2015-09-25 0:54 ` Chanwoo Choi
2015-09-16 9:56 ` [PATCH 2/6] extcon: arizona: Add device binding for the general purpose switch Charles Keepax
2015-09-25 0:54 ` Chanwoo Choi
2015-09-16 9:56 ` [PATCH 3/6] extcon: arizona: Add device binding for jack detect polarity inversion Charles Keepax
2015-09-16 9:56 ` [PATCH 4/6] extcon: arizona: Add device binding for second jack detect pin on GPIO5 Charles Keepax
2015-09-25 0:54 ` Chanwoo Choi
2015-09-25 9:10 ` Charles Keepax
2015-09-27 4:50 ` Chanwoo Choi
2015-09-16 9:56 ` [PATCH 5/6] mfd: arizona: Update DT binding documentation for mic detection Charles Keepax
2015-09-20 4:16 ` Lee Jones
2015-09-16 9:56 ` Charles Keepax [this message]
2015-09-20 4:17 ` [PATCH 6/6] mfd: arizona: Update DT binding documentation for jack detection Lee Jones
-- strict thread matches above, loose matches on Subject: below --
2015-09-10 11:41 [PATCH 1/6] mfd: arizona: Add TST_CAP bits for headphone detection Charles Keepax
2015-09-10 11:41 ` [PATCH 6/6] mfd: arizona: Update DT binding documentation for jack detection Charles Keepax
2015-09-11 8:09 ` Chanwoo Choi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1442397404-7579-7-git-send-email-ckeepax@opensource.wolfsonmicro.com \
--to=ckeepax@opensource.wolfsonmicro.com \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=lee.jones@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=myungjoo.ham@samsung.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
--cc=sameo@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome