From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1752914AbbJONOX (ORCPT ); Thu, 15 Oct 2015 09:14:23 -0400 Received: from mout01.posteo.de ([185.67.36.65]:43582 "EHLO mout01.posteo.de" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752756AbbJONOV (ORCPT ); Thu, 15 Oct 2015 09:14:21 -0400 From: Martin Kepplinger To: robh+dt@kernel.org, pawel.moll@arm.com, mark.rutland@arm.com, ijc+devicetree@hellion.org.uk, galak@codeaurora.org, jic23@kernel.org, knaack.h@gmx.de, lars@metafoo.de, pmeerw@pmeerw.net, mfuzzey@parkeon.com Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-iio@vger.kernel.org, Martin Kepplinger , Martin Kepplinger Subject: [PATCH v4] iio: mma8452: support either of the available interrupt pins Date: Thu, 15 Oct 2015 15:10:32 +0200 Message-Id: <1444914632-4486-1-git-send-email-martink@posteo.de> X-Mailer: git-send-email 2.1.4 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org This change is important in order for everyone to be easily able to use the driver for one of the supported accelerometer chips! Until now, the driver blindly assumed that the INT1 interrupt line is wired on a user's board. But these devices have 2 interrupt lines and can route their interrupt sources to one of them. Now, if "INT2" is found and matches i2c_client->irq, INT2 will be used. The chip's default actually is INT2, which is why probably many boards will have it wired and can make use of this. Of course, this also falls back to assuming INT1, so for existing users nothing will break. The new functionality is described in the bindings doc. Signed-off-by: Martin Kepplinger --- changelog: v4: use irq that matches client->irq, backwards compatible v3: correctly assign irq if both pins are described in DT v2: don't warn but normally handle if both pins are described in dts thanks Mark Rutland v1: initial post .../devicetree/bindings/iio/accel/mma8452.txt | 6 ++++++ drivers/iio/accel/mma8452.c | 21 +++++++++++++++------ 2 files changed, 21 insertions(+), 6 deletions(-) diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt index e3c3746..3c10e85 100644 --- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt @@ -7,13 +7,18 @@ Required properties: * "fsl,mma8453" * "fsl,mma8652" * "fsl,mma8653" + - reg: the I2C address of the chip Optional properties: - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: interrupt mapping for GPIO IRQ + - interrupt-names: should contain "INT1" and/or "INT2", the accelerometer's + interrupt line in use. + Example: mma8453fc@1d { @@ -21,4 +26,5 @@ Example: reg = <0x1d>; interrupt-parent = <&gpio1>; interrupts = <5 0>; + interrupt-names = "INT2"; }; diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c index 1eccc2d..116a6e4 100644 --- a/drivers/iio/accel/mma8452.c +++ b/drivers/iio/accel/mma8452.c @@ -29,6 +29,7 @@ #include #include #include +#include #define MMA8452_STATUS 0x00 #define MMA8452_STATUS_DRDY (BIT(2) | BIT(1) | BIT(0)) @@ -1130,13 +1131,21 @@ static int mma8452_probe(struct i2c_client *client, MMA8452_INT_FF_MT; int enabled_interrupts = MMA8452_INT_TRANS | MMA8452_INT_FF_MT; + int irq2; - /* Assume wired to INT1 pin */ - ret = i2c_smbus_write_byte_data(client, - MMA8452_CTRL_REG5, - supported_interrupts); - if (ret < 0) - return ret; + irq2 = of_irq_get_byname(client->dev.of_node, "INT2"); + + if (irq2 == client->irq) { + dev_dbg(&client->dev, "using interrupt line INT2\n"); + } else { + ret = i2c_smbus_write_byte_data(client, + MMA8452_CTRL_REG5, + supported_interrupts); + if (ret < 0) + return ret; + + dev_dbg(&client->dev, "using interrupt line INT1\n"); + } ret = i2c_smbus_write_byte_data(client, MMA8452_CTRL_REG4, -- 2.1.4