From: Chris Metcalf <cmetcalf@ezchip.com>
To: Gilad Ben Yossef <giladb@ezchip.com>,
Steven Rostedt <rostedt@goodmis.org>,
Ingo Molnar <mingo@kernel.org>,
Peter Zijlstra <peterz@infradead.org>,
Andrew Morton <akpm@linux-foundation.org>,
"Rik van Riel" <riel@redhat.com>, Tejun Heo <tj@kernel.org>,
Frederic Weisbecker <fweisbec@gmail.com>,
Thomas Gleixner <tglx@linutronix.de>,
"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>,
Christoph Lameter <cl@linux.com>,
Viresh Kumar <viresh.kumar@linaro.org>,
Catalin Marinas <catalin.marinas@arm.com>,
Will Deacon <will.deacon@arm.com>,
Andy Lutomirski <luto@amacapital.net>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Subject: [PATCH v8 11/14] arch/arm64: enable task isolation functionality
Date: Tue, 20 Oct 2015 16:36:09 -0400 [thread overview]
Message-ID: <1445373372-6567-12-git-send-email-cmetcalf@ezchip.com> (raw)
In-Reply-To: <1445373372-6567-1-git-send-email-cmetcalf@ezchip.com>
We need to call task_isolation_enter() from prepare_exit_to_usermode(),
so that we can both ensure we do it last before returning to
userspace, and we also are able to re-run signal handling, etc.,
if something occurs while task_isolation_enter() has interrupts
enabled. To do this we add _TIF_NOHZ to the _TIF_WORK_MASK if
we have CONFIG_TASK_ISOLATION enabled, which brings us into
prepare_exit_to_usermode() on all return to userspace. But we
don't put _TIF_NOHZ in the flags that we use to loop back and
recheck, since we don't need to loop back only because the flag
is set. Instead we unconditionally call task_isolation_enter()
at the end of the loop if any other work is done.
To make the assembly code continue to be as optimized as before,
we renumber the _TIF flags so that both _TIF_WORK_MASK and
_TIF_SYSCALL_WORK still have contiguous runs of bits in the
immediate operand for the "and" instruction, as required by the
ARM64 ISA. Since TIF_NOHZ is in both masks, it must be the
middle bit in the contiguous run that starts with the
_TIF_WORK_MASK bits and ends with the _TIF_SYSCALL_WORK bits.
We tweak syscall_trace_enter() slightly to carry the "flags"
value from current_thread_info()->flags for each of the tests,
rather than doing a volatile read from memory for each one. This
avoids a small overhead for each test, and in particular avoids
that overhead for TIF_NOHZ when TASK_ISOLATION is not enabled.
Finally, add an explicit check for STRICT mode in do_mem_abort()
to handle the case of page faults.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
---
arch/arm64/include/asm/thread_info.h | 18 ++++++++++++------
arch/arm64/kernel/ptrace.c | 12 +++++++++---
arch/arm64/kernel/signal.c | 7 +++++--
arch/arm64/mm/fault.c | 4 ++++
4 files changed, 30 insertions(+), 11 deletions(-)
diff --git a/arch/arm64/include/asm/thread_info.h b/arch/arm64/include/asm/thread_info.h
index dcd06d18a42a..4c36c4ee3528 100644
--- a/arch/arm64/include/asm/thread_info.h
+++ b/arch/arm64/include/asm/thread_info.h
@@ -101,11 +101,11 @@ static inline struct thread_info *current_thread_info(void)
#define TIF_NEED_RESCHED 1
#define TIF_NOTIFY_RESUME 2 /* callback before returning to user */
#define TIF_FOREIGN_FPSTATE 3 /* CPU's FP state is not current's */
-#define TIF_NOHZ 7
-#define TIF_SYSCALL_TRACE 8
-#define TIF_SYSCALL_AUDIT 9
-#define TIF_SYSCALL_TRACEPOINT 10
-#define TIF_SECCOMP 11
+#define TIF_NOHZ 4
+#define TIF_SYSCALL_TRACE 5
+#define TIF_SYSCALL_AUDIT 6
+#define TIF_SYSCALL_TRACEPOINT 7
+#define TIF_SECCOMP 8
#define TIF_MEMDIE 18 /* is terminating due to OOM killer */
#define TIF_FREEZE 19
#define TIF_RESTORE_SIGMASK 20
@@ -124,9 +124,15 @@ static inline struct thread_info *current_thread_info(void)
#define _TIF_SECCOMP (1 << TIF_SECCOMP)
#define _TIF_32BIT (1 << TIF_32BIT)
-#define _TIF_WORK_MASK (_TIF_NEED_RESCHED | _TIF_SIGPENDING | \
+#define _TIF_WORK_LOOP_MASK (_TIF_NEED_RESCHED | _TIF_SIGPENDING | \
_TIF_NOTIFY_RESUME | _TIF_FOREIGN_FPSTATE)
+#ifdef CONFIG_TASK_ISOLATION
+# define _TIF_WORK_MASK (_TIF_WORK_LOOP_MASK | _TIF_NOHZ)
+#else
+# define _TIF_WORK_MASK _TIF_WORK_LOOP_MASK
+#endif
+
#define _TIF_SYSCALL_WORK (_TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT | \
_TIF_SYSCALL_TRACEPOINT | _TIF_SECCOMP | \
_TIF_NOHZ)
diff --git a/arch/arm64/kernel/ptrace.c b/arch/arm64/kernel/ptrace.c
index 1971f491bb90..69ed3ba81650 100644
--- a/arch/arm64/kernel/ptrace.c
+++ b/arch/arm64/kernel/ptrace.c
@@ -37,6 +37,7 @@
#include <linux/regset.h>
#include <linux/tracehook.h>
#include <linux/elf.h>
+#include <linux/isolation.h>
#include <asm/compat.h>
#include <asm/debug-monitors.h>
@@ -1240,14 +1241,19 @@ static void tracehook_report_syscall(struct pt_regs *regs,
asmlinkage int syscall_trace_enter(struct pt_regs *regs)
{
- /* Do the secure computing check first; failures should be fast. */
+ unsigned long work = ACCESS_ONCE(current_thread_info()->flags);
+
+ if ((work & _TIF_NOHZ) && task_isolation_check_syscall(regs->syscallno))
+ return -1;
+
+ /* Do the secure computing check early; failures should be fast. */
if (secure_computing() == -1)
return -1;
- if (test_thread_flag(TIF_SYSCALL_TRACE))
+ if (work & _TIF_SYSCALL_TRACE)
tracehook_report_syscall(regs, PTRACE_SYSCALL_ENTER);
- if (test_thread_flag(TIF_SYSCALL_TRACEPOINT))
+ if (work & _TIF_SYSCALL_TRACEPOINT)
trace_sys_enter(regs, regs->syscallno);
audit_syscall_entry(regs->syscallno, regs->orig_x0, regs->regs[1],
diff --git a/arch/arm64/kernel/signal.c b/arch/arm64/kernel/signal.c
index fde59c1139a9..641c828653c7 100644
--- a/arch/arm64/kernel/signal.c
+++ b/arch/arm64/kernel/signal.c
@@ -25,6 +25,7 @@
#include <linux/uaccess.h>
#include <linux/tracehook.h>
#include <linux/ratelimit.h>
+#include <linux/isolation.h>
#include <asm/debug-monitors.h>
#include <asm/elf.h>
@@ -419,10 +420,12 @@ asmlinkage void prepare_exit_to_usermode(struct pt_regs *regs,
if (thread_flags & _TIF_FOREIGN_FPSTATE)
fpsimd_restore_current_state();
+ task_isolation_enter();
+
local_irq_disable();
thread_flags = READ_ONCE(current_thread_info()->flags) &
- _TIF_WORK_MASK;
+ _TIF_WORK_LOOP_MASK;
- } while (thread_flags);
+ } while (thread_flags || !task_isolation_ready());
}
diff --git a/arch/arm64/mm/fault.c b/arch/arm64/mm/fault.c
index 9fadf6d7039b..a726f9f3ef3c 100644
--- a/arch/arm64/mm/fault.c
+++ b/arch/arm64/mm/fault.c
@@ -29,6 +29,7 @@
#include <linux/sched.h>
#include <linux/highmem.h>
#include <linux/perf_event.h>
+#include <linux/isolation.h>
#include <asm/cpufeature.h>
#include <asm/exception.h>
@@ -466,6 +467,9 @@ asmlinkage void __exception do_mem_abort(unsigned long addr, unsigned int esr,
const struct fault_info *inf = fault_info + (esr & 63);
struct siginfo info;
+ if (user_mode(regs))
+ task_isolation_check_exception("%s at %#lx", inf->name, addr);
+
if (!inf->fn(addr, esr, regs))
return;
--
2.1.2
next prev parent reply other threads:[~2015-10-20 20:37 UTC|newest]
Thread overview: 236+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-05-08 17:58 [PATCH 0/6] support "dataplane" mode for nohz_full Chris Metcalf
2015-05-08 17:58 ` [PATCH 1/6] nohz_full: add support for "dataplane" mode Chris Metcalf
2015-05-08 17:58 ` [PATCH 2/6] nohz: dataplane: allow tick to be fully disabled for dataplane Chris Metcalf
2015-05-12 9:26 ` Peter Zijlstra
2015-05-12 13:12 ` Paul E. McKenney
2015-05-14 20:55 ` Chris Metcalf
2015-05-08 17:58 ` [PATCH 3/6] dataplane nohz: run softirqs synchronously on user entry Chris Metcalf
2015-05-09 7:04 ` Mike Galbraith
2015-05-11 20:13 ` Chris Metcalf
2015-05-12 2:21 ` Mike Galbraith
2015-05-12 9:28 ` Peter Zijlstra
2015-05-12 9:32 ` Peter Zijlstra
2015-05-12 13:08 ` Paul E. McKenney
2015-05-08 17:58 ` [PATCH 4/6] nohz: support PR_DATAPLANE_QUIESCE Chris Metcalf
2015-05-12 9:33 ` Peter Zijlstra
2015-05-12 9:50 ` Ingo Molnar
2015-05-12 10:38 ` Peter Zijlstra
2015-05-12 12:52 ` Ingo Molnar
2015-05-13 4:35 ` Andy Lutomirski
2015-05-13 17:51 ` Paul E. McKenney
2015-05-14 20:55 ` Chris Metcalf
2015-05-14 20:54 ` Chris Metcalf
2015-05-08 17:58 ` [PATCH 5/6] nohz: support PR_DATAPLANE_STRICT mode Chris Metcalf
2015-05-09 7:28 ` Andy Lutomirski
2015-05-09 10:37 ` Gilad Ben Yossef
2015-05-11 19:13 ` Chris Metcalf
2015-05-11 22:28 ` Andy Lutomirski
2015-05-12 21:06 ` Chris Metcalf
2015-05-12 22:23 ` Andy Lutomirski
2015-05-15 21:25 ` Chris Metcalf
2015-05-12 9:38 ` Peter Zijlstra
2015-05-12 13:20 ` Paul E. McKenney
2015-05-08 17:58 ` [PATCH 6/6] nohz: add dataplane_debug boot flag Chris Metcalf
2015-05-08 21:18 ` [PATCH 0/6] support "dataplane" mode for nohz_full Andrew Morton
2015-05-08 21:22 ` Steven Rostedt
2015-05-08 23:11 ` Chris Metcalf
2015-05-08 23:19 ` Andrew Morton
2015-05-09 7:05 ` Ingo Molnar
2015-05-09 7:19 ` Andy Lutomirski
2015-05-11 19:54 ` Chris Metcalf
2015-05-11 22:15 ` Andy Lutomirski
[not found] ` <55510885.9070101@ezchip.com>
2015-05-12 13:18 ` Paul E. McKenney
2015-05-09 7:19 ` Mike Galbraith
2015-05-09 10:18 ` Gilad Ben Yossef
2015-05-11 12:57 ` Steven Rostedt
2015-05-11 15:36 ` Frederic Weisbecker
2015-05-11 19:19 ` Mike Galbraith
2015-05-11 19:25 ` Chris Metcalf
2015-05-12 1:47 ` Mike Galbraith
2015-05-12 4:35 ` Mike Galbraith
2015-05-15 15:05 ` Chris Metcalf
2015-05-15 18:44 ` Mike Galbraith
2015-05-26 19:51 ` Chris Metcalf
2015-05-27 3:28 ` Mike Galbraith
2015-05-11 17:19 ` Paul E. McKenney
2015-05-11 17:27 ` Andrew Morton
2015-05-11 17:33 ` Frederic Weisbecker
2015-05-11 18:00 ` Steven Rostedt
2015-05-11 18:09 ` Chris Metcalf
2015-05-11 18:36 ` Steven Rostedt
2015-05-12 9:10 ` CONFIG_ISOLATION=y (was: [PATCH 0/6] support "dataplane" mode for nohz_full) Ingo Molnar
2015-05-12 11:48 ` Peter Zijlstra
2015-05-12 12:34 ` Ingo Molnar
2015-05-12 12:39 ` Peter Zijlstra
2015-05-12 12:43 ` Ingo Molnar
2015-05-12 15:36 ` Frederic Weisbecker
2015-05-12 21:05 ` CONFIG_ISOLATION=y Chris Metcalf
2015-05-12 10:46 ` [PATCH 0/6] support "dataplane" mode for nohz_full Peter Zijlstra
2015-05-15 15:10 ` Chris Metcalf
2015-05-15 21:26 ` [PATCH v2 0/5] support "cpu_isolated" " Chris Metcalf
2015-05-15 21:27 ` [PATCH v2 1/5] nohz_full: add support for "cpu_isolated" mode Chris Metcalf
2015-05-15 21:27 ` [PATCH v2 2/5] nohz: support PR_CPU_ISOLATED_STRICT mode Chris Metcalf
2015-05-15 21:27 ` [PATCH v2 3/5] nohz: cpu_isolated strict mode configurable signal Chris Metcalf
2015-05-15 21:27 ` [PATCH v2 4/5] nohz: add cpu_isolated_debug boot flag Chris Metcalf
2015-05-15 21:27 ` [PATCH v2 5/5] nohz: cpu_isolated: allow tick to be fully disabled Chris Metcalf
2015-05-15 22:17 ` [PATCH v2 1/5] nohz_full: add support for "cpu_isolated" mode Thomas Gleixner
2015-05-28 20:38 ` Chris Metcalf
2015-06-03 15:29 ` [PATCH v3 0/5] support "cpu_isolated" mode for nohz_full Chris Metcalf
2015-06-03 15:29 ` [PATCH v3 1/5] nohz_full: add support for "cpu_isolated" mode Chris Metcalf
2015-06-03 15:29 ` [PATCH v3 2/5] nohz: support PR_CPU_ISOLATED_STRICT mode Chris Metcalf
2015-06-03 15:29 ` [PATCH v3 3/5] nohz: cpu_isolated strict mode configurable signal Chris Metcalf
2015-06-03 15:29 ` [PATCH v3 4/5] nohz: add cpu_isolated_debug boot flag Chris Metcalf
2015-06-03 15:29 ` [PATCH v3 5/5] nohz: cpu_isolated: allow tick to be fully disabled Chris Metcalf
2015-07-13 19:57 ` [PATCH v4 0/5] support "cpu_isolated" mode for nohz_full Chris Metcalf
2015-07-13 19:57 ` [PATCH v4 1/5] nohz_full: add support for "cpu_isolated" mode Chris Metcalf
2015-07-13 20:40 ` Andy Lutomirski
2015-07-13 21:01 ` Chris Metcalf
2015-07-13 21:45 ` Andy Lutomirski
2015-07-21 19:10 ` Chris Metcalf
2015-07-21 19:26 ` Andy Lutomirski
2015-07-21 20:36 ` Paul E. McKenney
2015-07-22 13:57 ` Christoph Lameter
2015-07-22 19:28 ` Paul E. McKenney
2015-07-22 20:02 ` Christoph Lameter
2015-07-24 20:21 ` Chris Metcalf
2015-07-24 20:22 ` Chris Metcalf
2015-07-24 14:03 ` Frederic Weisbecker
2015-07-24 20:19 ` Chris Metcalf
2015-07-24 13:27 ` Frederic Weisbecker
2015-07-24 20:21 ` Chris Metcalf
2015-07-13 19:57 ` [PATCH v4 2/5] nohz: support PR_CPU_ISOLATED_STRICT mode Chris Metcalf
2015-07-13 21:47 ` Andy Lutomirski
2015-07-21 19:34 ` Chris Metcalf
2015-07-21 19:42 ` Andy Lutomirski
2015-07-24 20:29 ` Chris Metcalf
2015-07-13 19:57 ` [PATCH v4 3/5] nohz: cpu_isolated strict mode configurable signal Chris Metcalf
2015-07-13 19:58 ` [PATCH v4 4/5] nohz: add cpu_isolated_debug boot flag Chris Metcalf
2015-07-13 19:58 ` [PATCH v4 5/5] nohz: cpu_isolated: allow tick to be fully disabled Chris Metcalf
2015-07-28 19:49 ` [PATCH v5 0/6] support "cpu_isolated" mode for nohz_full Chris Metcalf
2015-07-28 19:49 ` [PATCH v5 1/6] vmstat: provide a function to quiet down the diff processing Chris Metcalf
2015-07-28 19:49 ` [PATCH v5 2/6] cpu_isolated: add initial support Chris Metcalf
2015-08-12 16:00 ` Frederic Weisbecker
2015-08-12 18:22 ` Chris Metcalf
2015-08-26 15:26 ` Frederic Weisbecker
2015-08-26 15:55 ` Chris Metcalf
2015-07-28 19:49 ` [PATCH v5 3/6] cpu_isolated: support PR_CPU_ISOLATED_STRICT mode Chris Metcalf
2015-07-28 19:49 ` [PATCH v5 4/6] cpu_isolated: provide strict mode configurable signal Chris Metcalf
2015-07-28 19:49 ` [PATCH v5 5/6] cpu_isolated: add debug boot flag Chris Metcalf
2015-07-28 19:49 ` [PATCH v5 6/6] nohz: cpu_isolated: allow tick to be fully disabled Chris Metcalf
2015-08-25 19:55 ` [PATCH v6 0/6] support "task_isolated" mode for nohz_full Chris Metcalf
2015-08-25 19:55 ` [PATCH v6 1/6] vmstat: provide a function to quiet down the diff processing Chris Metcalf
2015-08-25 19:55 ` [PATCH v6 2/6] task_isolation: add initial support Chris Metcalf
2015-08-25 19:55 ` [PATCH v6 3/6] task_isolation: support PR_TASK_ISOLATION_STRICT mode Chris Metcalf
2015-08-26 10:36 ` Will Deacon
2015-08-26 15:10 ` Chris Metcalf
2015-09-02 10:13 ` Will Deacon
2015-08-28 15:31 ` [PATCH v6.1 " Chris Metcalf
2015-08-25 19:55 ` [PATCH v6 4/6] task_isolation: provide strict mode configurable signal Chris Metcalf
2015-08-28 19:22 ` Andy Lutomirski
2015-09-02 18:38 ` [PATCH v6.2 3/6] task_isolation: support PR_TASK_ISOLATION_STRICT mode Chris Metcalf
2015-08-25 19:55 ` [PATCH v6 5/6] task_isolation: add debug boot flag Chris Metcalf
2015-08-25 19:55 ` [PATCH v6 6/6] nohz: task_isolation: allow tick to be fully disabled Chris Metcalf
2015-09-28 15:17 ` [PATCH v7 00/11] support "task_isolated" mode for nohz_full Chris Metcalf
2015-09-28 15:17 ` [PATCH v7 01/11] vmstat: provide a function to quiet down the diff processing Chris Metcalf
2015-09-28 15:17 ` [PATCH v7 02/11] task_isolation: add initial support Chris Metcalf
2015-10-01 12:14 ` Frederic Weisbecker
2015-10-01 12:18 ` Thomas Gleixner
2015-10-01 12:23 ` Frederic Weisbecker
2015-10-01 12:31 ` Thomas Gleixner
2015-10-01 17:02 ` Chris Metcalf
2015-10-01 21:20 ` Thomas Gleixner
2015-10-02 17:15 ` Chris Metcalf
2015-10-02 19:02 ` Thomas Gleixner
2015-10-01 19:25 ` Chris Metcalf
2015-09-28 15:17 ` [PATCH v7 03/11] task_isolation: support PR_TASK_ISOLATION_STRICT mode Chris Metcalf
2015-09-28 20:51 ` Andy Lutomirski
2015-09-28 21:54 ` Chris Metcalf
2015-09-28 22:38 ` Andy Lutomirski
2015-09-29 17:35 ` Chris Metcalf
2015-09-29 17:46 ` Andy Lutomirski
2015-09-29 17:57 ` Chris Metcalf
2015-09-29 18:00 ` Andy Lutomirski
2015-10-01 19:25 ` Chris Metcalf
2015-09-28 15:17 ` [PATCH v7 04/11] task_isolation: provide strict mode configurable signal Chris Metcalf
2015-09-28 20:54 ` Andy Lutomirski
2015-09-28 21:54 ` Chris Metcalf
2015-09-28 15:17 ` [PATCH v7 05/11] task_isolation: add debug boot flag Chris Metcalf
2015-09-28 20:59 ` Andy Lutomirski
2015-09-28 21:55 ` Chris Metcalf
2015-09-28 22:40 ` Andy Lutomirski
2015-09-29 17:35 ` Chris Metcalf
2015-10-05 17:07 ` Luiz Capitulino
2015-10-08 0:33 ` Chris Metcalf
2015-10-08 20:28 ` Luiz Capitulino
2015-09-28 15:17 ` [PATCH v7 06/11] nohz: task_isolation: allow tick to be fully disabled Chris Metcalf
2015-09-28 20:40 ` Andy Lutomirski
2015-10-01 13:07 ` Frederic Weisbecker
2015-10-01 14:13 ` Thomas Gleixner
2015-09-28 15:17 ` [PATCH v7 07/11] arch/x86: enable task isolation functionality Chris Metcalf
2015-09-28 20:59 ` Andy Lutomirski
2015-09-28 21:57 ` Chris Metcalf
2015-09-28 22:43 ` Andy Lutomirski
2015-09-29 17:42 ` Chris Metcalf
2015-09-29 17:57 ` Andy Lutomirski
2015-09-30 20:25 ` Thomas Gleixner
2015-09-30 20:58 ` Chris Metcalf
2015-09-30 22:02 ` Thomas Gleixner
2015-09-30 22:11 ` Andy Lutomirski
2015-10-01 8:12 ` Thomas Gleixner
2015-10-01 9:08 ` Christoph Lameter
2015-10-01 10:10 ` Thomas Gleixner
2015-10-01 19:25 ` Chris Metcalf
2015-09-28 15:17 ` [PATCH v7 08/11] arch/arm64: adopt prepare_exit_to_usermode() model from x86 Chris Metcalf
2015-09-28 15:17 ` [PATCH v7 09/11] arch/arm64: enable task isolation functionality Chris Metcalf
2015-09-28 15:17 ` [PATCH v7 10/11] arch/tile: adopt prepare_exit_to_usermode() model from x86 Chris Metcalf
2015-09-28 15:17 ` [PATCH v7 11/11] arch/tile: enable task isolation functionality Chris Metcalf
2015-10-20 20:35 ` [PATCH v8 00/14] support "task_isolation" mode for nohz_full Chris Metcalf
2015-10-20 20:35 ` [PATCH v8 01/14] vmstat: provide a function to quiet down the diff processing Chris Metcalf
2015-10-20 20:36 ` [PATCH v8 02/14] vmstat: add vmstat_idle function Chris Metcalf
2015-10-20 20:45 ` Christoph Lameter
2015-10-20 20:36 ` [PATCH v8 03/14] lru_add_drain_all: factor out lru_add_drain_needed Chris Metcalf
2015-10-20 20:36 ` [PATCH v8 04/14] task_isolation: add initial support Chris Metcalf
2015-10-20 20:56 ` Andy Lutomirski
2015-10-20 21:20 ` Chris Metcalf
2015-10-20 21:26 ` Andy Lutomirski
2015-10-21 0:29 ` Steven Rostedt
2015-10-26 20:19 ` Chris Metcalf
2015-10-26 21:13 ` Chris Metcalf
2015-10-26 20:32 ` Chris Metcalf
2015-10-21 16:12 ` Frederic Weisbecker
2015-10-27 16:40 ` Chris Metcalf
2016-01-28 16:38 ` Frederic Weisbecker
2016-02-11 19:58 ` Chris Metcalf
2015-10-20 20:36 ` [PATCH v8 05/14] task_isolation: support PR_TASK_ISOLATION_STRICT mode Chris Metcalf
2015-10-20 20:36 ` [PATCH v8 06/14] task_isolation: provide strict mode configurable signal Chris Metcalf
2015-10-21 0:56 ` Steven Rostedt
2015-10-21 1:30 ` Chris Metcalf
2015-10-21 1:41 ` Steven Rostedt
2015-10-21 1:42 ` Andy Lutomirski
2015-10-21 6:41 ` Gilad Ben Yossef
2015-10-21 18:53 ` Andy Lutomirski
2015-10-22 20:44 ` Chris Metcalf
2015-10-22 21:00 ` Andy Lutomirski
2015-10-27 19:37 ` Chris Metcalf
2015-10-24 9:16 ` Gilad Ben Yossef
2015-10-20 20:36 ` [PATCH v8 07/14] task_isolation: add debug boot flag Chris Metcalf
2015-10-20 20:36 ` [PATCH v8 08/14] nohz_full: allow disabling the 1Hz minimum tick at boot Chris Metcalf
2015-10-20 21:03 ` Frederic Weisbecker
2015-10-20 21:18 ` Chris Metcalf
2015-10-21 0:59 ` Steven Rostedt
2015-10-21 6:56 ` Gilad Ben Yossef
2015-10-21 14:28 ` Christoph Lameter
2015-10-21 15:35 ` Frederic Weisbecker
2015-10-20 20:36 ` [PATCH v8 09/14] arch/x86: enable task isolation functionality Chris Metcalf
2015-10-20 20:36 ` [PATCH v8 10/14] arch/arm64: adopt prepare_exit_to_usermode() model from x86 Chris Metcalf
2015-10-20 20:36 ` Chris Metcalf [this message]
2015-10-20 20:36 ` [PATCH v8 12/14] arch/tile: " Chris Metcalf
2015-10-20 20:36 ` [PATCH v8 13/14] arch/tile: turn off timer tick for oneshot_stopped state Chris Metcalf
2015-10-20 20:36 ` [PATCH v8 14/14] arch/tile: enable task isolation functionality Chris Metcalf
2015-10-21 12:39 ` [PATCH v8 00/14] support "task_isolation" mode for nohz_full Peter Zijlstra
2015-10-22 20:31 ` Chris Metcalf
2015-10-23 2:33 ` Frederic Weisbecker
2015-10-23 8:49 ` Peter Zijlstra
2015-10-23 13:29 ` Frederic Weisbecker
2015-10-23 9:04 ` Peter Zijlstra
2015-10-23 11:52 ` Theodore Ts'o
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1445373372-6567-12-git-send-email-cmetcalf@ezchip.com \
--to=cmetcalf@ezchip.com \
--cc=akpm@linux-foundation.org \
--cc=catalin.marinas@arm.com \
--cc=cl@linux.com \
--cc=fweisbec@gmail.com \
--cc=giladb@ezchip.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=luto@amacapital.net \
--cc=mingo@kernel.org \
--cc=paulmck@linux.vnet.ibm.com \
--cc=peterz@infradead.org \
--cc=riel@redhat.com \
--cc=rostedt@goodmis.org \
--cc=tglx@linutronix.de \
--cc=tj@kernel.org \
--cc=viresh.kumar@linaro.org \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®