From: Rasmus Villemoes <linux@rasmusvillemoes.dk>
To: Alessandro Zummo <a.zummo@towertech.it>,
Alexandre Belloni <alexandre.belloni@free-electrons.com>,
Joshua Kinard <kumba@gentoo.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>,
rtc-linux@googlegroups.com, linux-kernel@vger.kernel.org
Subject: [PATCH 1/2] drivers/rtc: use %ph for short hex dumps
Date: Tue, 24 Nov 2015 14:51:23 +0100 [thread overview]
Message-ID: <1448373085-6353-1-git-send-email-linux@rasmusvillemoes.dk> (raw)
This makes the generated code slightly smaller.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
drivers/rtc/rtc-ds1305.c | 8 ++------
drivers/rtc/rtc-ds1307.c | 17 ++++-------------
drivers/rtc/rtc-ds1685.c | 12 +++++-------
3 files changed, 11 insertions(+), 26 deletions(-)
diff --git a/drivers/rtc/rtc-ds1305.c b/drivers/rtc/rtc-ds1305.c
index 85706a9f82c9..f39691eea736 100644
--- a/drivers/rtc/rtc-ds1305.c
+++ b/drivers/rtc/rtc-ds1305.c
@@ -186,9 +186,7 @@ static int ds1305_get_time(struct device *dev, struct rtc_time *time)
if (status < 0)
return status;
- dev_vdbg(dev, "%s: %02x %02x %02x, %02x %02x %02x %02x\n",
- "read", buf[0], buf[1], buf[2], buf[3],
- buf[4], buf[5], buf[6]);
+ dev_vdbg(dev, "%s: %3ph, %4ph\n", "read", &buf[0], &buf[3]);
/* Decode the registers */
time->tm_sec = bcd2bin(buf[DS1305_SEC]);
@@ -232,9 +230,7 @@ static int ds1305_set_time(struct device *dev, struct rtc_time *time)
*bp++ = bin2bcd(time->tm_mon + 1);
*bp++ = bin2bcd(time->tm_year - 100);
- dev_dbg(dev, "%s: %02x %02x %02x, %02x %02x %02x %02x\n",
- "write", buf[1], buf[2], buf[3],
- buf[4], buf[5], buf[6], buf[7]);
+ dev_dbg(dev, "%s: %3ph, %4ph\n", "write", &buf[1], &buf[4]);
/* use write-then-read since dma from stack is nonportable */
return spi_write_then_read(ds1305->spi, buf, sizeof(buf),
diff --git a/drivers/rtc/rtc-ds1307.c b/drivers/rtc/rtc-ds1307.c
index 188006c55ce0..b72e782fbf44 100644
--- a/drivers/rtc/rtc-ds1307.c
+++ b/drivers/rtc/rtc-ds1307.c
@@ -464,13 +464,8 @@ static int ds1337_read_alarm(struct device *dev, struct rtc_wkalrm *t)
return -EIO;
}
- dev_dbg(dev, "%s: %02x %02x %02x %02x, %02x %02x %02x, %02x %02x\n",
- "alarm read",
- ds1307->regs[0], ds1307->regs[1],
- ds1307->regs[2], ds1307->regs[3],
- ds1307->regs[4], ds1307->regs[5],
- ds1307->regs[6], ds1307->regs[7],
- ds1307->regs[8]);
+ dev_dbg(dev, "%s: %4ph, %3ph, %2ph\n", "alarm read",
+ &ds1307->regs[0], &ds1307->regs[4], &ds1307->regs[7]);
/*
* report alarm time (ALARM1); assume 24 hour and day-of-month modes,
@@ -526,12 +521,8 @@ static int ds1337_set_alarm(struct device *dev, struct rtc_wkalrm *t)
control = ds1307->regs[7];
status = ds1307->regs[8];
- dev_dbg(dev, "%s: %02x %02x %02x %02x, %02x %02x %02x, %02x %02x\n",
- "alarm set (old status)",
- ds1307->regs[0], ds1307->regs[1],
- ds1307->regs[2], ds1307->regs[3],
- ds1307->regs[4], ds1307->regs[5],
- ds1307->regs[6], control, status);
+ dev_dbg(dev, "%s: %4ph, %3ph, %02x %02x\n", "alarm set (old status)",
+ &ds1307->regs[0], &ds1307->regs[4], control, status);
/* set ALARM1, using 24 hour and day-of-month modes */
buf[0] = bin2bcd(t->time.tm_sec);
diff --git a/drivers/rtc/rtc-ds1685.c b/drivers/rtc/rtc-ds1685.c
index 05a51ef52703..5038122aa8de 100644
--- a/drivers/rtc/rtc-ds1685.c
+++ b/drivers/rtc/rtc-ds1685.c
@@ -853,7 +853,7 @@ ds1685_rtc_proc(struct device *dev, struct seq_file *seq)
"Periodic Rate\t: %s\n"
"SQW Freq\t: %s\n"
#ifdef CONFIG_RTC_DS1685_PROC_REGS
- "Serial #\t: %02x:%02x:%02x:%02x:%02x:%02x:%02x:%02x\n"
+ "Serial #\t: %8phC\n"
"Register Status\t:\n"
" Ctrl A\t: UIP DV2 DV1 DV0 RS3 RS2 RS1 RS0\n"
"\t\t: %s\n"
@@ -872,7 +872,7 @@ ds1685_rtc_proc(struct device *dev, struct seq_file *seq)
" Ctrl 4B\t: ABE E32k CS RCE PRS RIE WIE KSE\n"
"\t\t: %s\n",
#else
- "Serial #\t: %02x:%02x:%02x:%02x:%02x:%02x:%02x:%02x\n",
+ "Serial #\t: %8phC\n",
#endif
model,
((ctrla & RTC_CTRL_A_DV1) ? "enabled" : "disabled"),
@@ -888,7 +888,7 @@ ds1685_rtc_proc(struct device *dev, struct seq_file *seq)
(!((ctrl4b & RTC_CTRL_4B_E32K)) ?
ds1685_rtc_sqw_freq[(ctrla & RTC_CTRL_A_RS_MASK)] : "32768Hz"),
#ifdef CONFIG_RTC_DS1685_PROC_REGS
- ssn[0], ssn[1], ssn[2], ssn[3], ssn[4], ssn[5], ssn[6], ssn[7],
+ ssn,
ds1685_rtc_print_regs(ctrla, bits[0]),
ds1685_rtc_print_regs(ctrlb, bits[1]),
ds1685_rtc_print_regs(ctrlc, bits[2]),
@@ -896,7 +896,7 @@ ds1685_rtc_proc(struct device *dev, struct seq_file *seq)
ds1685_rtc_print_regs(ctrl4a, bits[4]),
ds1685_rtc_print_regs(ctrl4b, bits[5]));
#else
- ssn[0], ssn[1], ssn[2], ssn[3], ssn[4], ssn[5], ssn[6], ssn[7]);
+ ssn);
#endif
return 0;
}
@@ -1160,9 +1160,7 @@ ds1685_rtc_sysfs_serial_show(struct device *dev,
ds1685_rtc_get_ssn(rtc, ssn);
ds1685_rtc_switch_to_bank0(rtc);
- return snprintf(buf, 24, "%02x:%02x:%02x:%02x:%02x:%02x:%02x:%02x\n",
- ssn[0], ssn[1], ssn[2], ssn[3], ssn[4], ssn[5],
- ssn[6], ssn[7]);
+ return snprintf(buf, 24, "%8phC\n", ssn);
return 0;
}
--
2.6.1
next reply other threads:[~2015-11-24 13:51 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-11-24 13:51 Rasmus Villemoes [this message]
2015-11-24 13:51 ` [PATCH 2/2] drivers/rtc/rtc-ds1685.c: don't try to micromanage sysfs output size Rasmus Villemoes
2015-11-30 19:06 ` Alexandre Belloni
2015-11-30 19:06 ` [PATCH 1/2] drivers/rtc: use %ph for short hex dumps Alexandre Belloni
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1448373085-6353-1-git-send-email-linux@rasmusvillemoes.dk \
--to=linux@rasmusvillemoes.dk \
--cc=a.zummo@towertech.it \
--cc=alexandre.belloni@free-electrons.com \
--cc=kumba@gentoo.org \
--cc=linux-kernel@vger.kernel.org \
--cc=rtc-linux@googlegroups.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®