From: Roman Volkov <v1ron@mail.ru>
To: Tony Prisk <linux@prisktech.co.nz>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Thomas Gleixner <tglx@linutronix.de>,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, Roman Volkov <rvolkov@v1ros.org>
Subject: [PATCH 4/4] clocksource/vt8500: Add register R/W functions
Date: Mon, 21 Dec 2015 01:28:12 +0300 [thread overview]
Message-ID: <1450650492-18996-5-git-send-email-v1ron@mail.ru> (raw)
In-Reply-To: <1450650492-18996-1-git-send-email-v1ron@mail.ru>
From: Roman Volkov <rvolkov@v1ros.org>
vt8500 timer requires special synchronization for accessing some of its
registers. Define special read and write functions to handle this process
transparently.
To perform a read from the Timer Count register, user must write a one
to the Timer Control register and wait for completion flag by polling the
Timer Read Count Active bit.
To perform a write to the Count or Match registers, user must poll the
write completion flag for the corresponding register to ensure that the
previous write completed and then write the actual value.
Signed-off-by: Roman Volkov <rvolkov@v1ros.org>
---
drivers/clocksource/vt8500_timer.c | 90 +++++++++++++++++++++++++++-----------
1 file changed, 65 insertions(+), 25 deletions(-)
diff --git a/drivers/clocksource/vt8500_timer.c b/drivers/clocksource/vt8500_timer.c
index 7649852..4d7513f 100644
--- a/drivers/clocksource/vt8500_timer.c
+++ b/drivers/clocksource/vt8500_timer.c
@@ -38,36 +38,75 @@
#define VT8500_TIMER_OFFSET 0x0100
#define VT8500_TIMER_HZ 3000000
-#define TIMER_MATCH_VAL 0x0000
+#define TIMER_MATCH0_VAL 0
+#define TIMER_MATCH1_VAL 0x04
+#define TIMER_MATCH2_VAL 0x08
+#define TIMER_MATCH3_VAL 0x0c
#define TIMER_COUNT_VAL 0x0010
#define TIMER_STATUS_VAL 0x0014
#define TIMER_IER_VAL 0x001c /* interrupt enable */
#define TIMER_CTRL_VAL 0x0020
#define TIMER_AS_VAL 0x0024 /* access status */
-#define TIMER_COUNT_R_ACTIVE (1 << 5) /* not ready for read */
-#define TIMER_COUNT_W_ACTIVE (1 << 4) /* not ready for write */
-#define TIMER_MATCH_W_ACTIVE (1 << 0) /* not ready for write */
-
-#define timer_readl(addr) readl_relaxed(regbase + addr)
-#define timer_writel(v, addr) writel_relaxed(v, regbase + addr)
+/* R/W status flags */
+#define TIMER_COUNT_R_ACTIVE (1 << 5)
+#define TIMER_COUNT_W_ACTIVE (1 << 4)
+#define TIMER_MATCH3_W_ACTIVE (1 << 3)
+#define TIMER_MATCH2_W_ACTIVE (1 << 2)
+#define TIMER_MATCH1_W_ACTIVE (1 << 1)
+#define TIMER_MATCH0_W_ACTIVE (1 << 0)
+
+#define vt8500_timer_sync(bit) { while (readl_relaxed \
+ (regbase + TIMER_AS_VAL) & bit) \
+ cpu_relax(); }
#define MIN_OSCR_DELTA 16
static void __iomem *regbase;
-static cycle_t vt8500_timer_read(struct clocksource *cs)
+static void vt8500_timer_write(unsigned long reg, u32 value)
+{
+ switch (reg) {
+ case TIMER_COUNT_VAL:
+ vt8500_timer_sync(TIMER_COUNT_W_ACTIVE);
+ break;
+ case TIMER_MATCH0_VAL:
+ vt8500_timer_sync(TIMER_MATCH0_W_ACTIVE);
+ break;
+ case TIMER_MATCH1_VAL:
+ vt8500_timer_sync(TIMER_MATCH1_W_ACTIVE);
+ break;
+ case TIMER_MATCH2_VAL:
+ vt8500_timer_sync(TIMER_MATCH2_W_ACTIVE);
+ break;
+ case TIMER_MATCH3_VAL:
+ vt8500_timer_sync(TIMER_MATCH3_W_ACTIVE);
+ break;
+ }
+
+ writel_relaxed(value, regbase + reg);
+}
+
+static u32 vt8500_timer_read(unsigned long reg)
{
- timer_writel(3, TIMER_CTRL_VAL);
- while (timer_readl(TIMER_AS_VAL) & TIMER_COUNT_R_ACTIVE)
- cpu_relax();
+ if (reg == TIMER_COUNT_VAL) {
+ vt8500_timer_write(TIMER_CTRL_VAL, 3);
+ vt8500_timer_sync(TIMER_COUNT_R_ACTIVE);
- return timer_readl(TIMER_COUNT_VAL);
+ return readl_relaxed(regbase + TIMER_COUNT_VAL);
+ }
+
+ return readl_relaxed(regbase + reg);
+}
+
+static cycle_t vt8500_oscr0_read(struct clocksource *cs)
+{
+ return vt8500_timer_read(TIMER_COUNT_VAL);
}
static struct clocksource clocksource = {
.name = "vt8500_timer",
.rating = 200,
- .read = vt8500_timer_read,
+ .read = vt8500_oscr0_read,
.mask = CLOCKSOURCE_MASK(32),
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
@@ -75,23 +114,24 @@ static struct clocksource clocksource = {
static int vt8500_timer_set_next_event(unsigned long cycles,
struct clock_event_device *evt)
{
- cycle_t alarm = clocksource.read(&clocksource) + cycles;
- while (timer_readl(TIMER_AS_VAL) & TIMER_MATCH_W_ACTIVE)
- cpu_relax();
- timer_writel((unsigned long)alarm, TIMER_MATCH_VAL);
+ unsigned long alarm = vt8500_timer_read(TIMER_COUNT_VAL) + cycles;
- if ((signed)(alarm - clocksource.read(&clocksource)) <= MIN_OSCR_DELTA)
+ vt8500_timer_write(TIMER_MATCH0_VAL, alarm);
+ if ((signed)(alarm - vt8500_timer_read(
+ TIMER_COUNT_VAL)) <= MIN_OSCR_DELTA) {
return -ETIME;
+ }
- timer_writel(1, TIMER_IER_VAL);
+ vt8500_timer_write(TIMER_IER_VAL, 1);
return 0;
}
static int vt8500_shutdown(struct clock_event_device *evt)
{
- timer_writel(timer_readl(TIMER_CTRL_VAL) | 1, TIMER_CTRL_VAL);
- timer_writel(0, TIMER_IER_VAL);
+ vt8500_timer_write(TIMER_CTRL_VAL,
+ vt8500_timer_read(TIMER_CTRL_VAL) | 1);
+ vt8500_timer_write(TIMER_IER_VAL, 0);
return 0;
}
@@ -107,7 +147,7 @@ static struct clock_event_device clockevent = {
static irqreturn_t vt8500_timer_interrupt(int irq, void *dev_id)
{
struct clock_event_device *evt = dev_id;
- timer_writel(0xf, TIMER_STATUS_VAL);
+ vt8500_timer_write(TIMER_STATUS_VAL, 0xf);
evt->event_handler(evt);
return IRQ_HANDLED;
@@ -137,9 +177,9 @@ static void __init vt8500_timer_init(struct device_node *np)
return;
}
- timer_writel(1, TIMER_CTRL_VAL);
- timer_writel(0xf, TIMER_STATUS_VAL);
- timer_writel(~0, TIMER_MATCH_VAL);
+ vt8500_timer_write(TIMER_CTRL_VAL, 1);
+ vt8500_timer_write(TIMER_STATUS_VAL, 0xf);
+ vt8500_timer_write(TIMER_MATCH0_VAL, ~0);
if (clocksource_register_hz(&clocksource, VT8500_TIMER_HZ))
pr_err("%s: vt8500_timer_init: clocksource_register failed for %s\n",
--
2.6.2
next prev parent reply other threads:[~2015-12-20 22:29 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-12-20 22:28 [PATCH 0/4] clocksource/vt8500: Fix hangs in small delays Roman Volkov
2015-12-20 22:28 ` [PATCH 1/4] clocksource/vt8500: Use [read\write]l_relaxed() Roman Volkov
2015-12-20 22:28 ` [PATCH 2/4] clocksource/vt8500: Remove the 'loops' variable Roman Volkov
2015-12-20 22:28 ` [PATCH 3/4] clocksource/vt8500: Use MIN_OSCR_DELTA from PXA Roman Volkov
2015-12-20 22:28 ` Roman Volkov [this message]
2015-12-21 9:54 ` [PATCH 4/4] clocksource/vt8500: Add register R/W functions Alexey Charkov
2015-12-21 8:29 ` [PATCH 0/4] clocksource/vt8500: Fix hangs in small delays Roman Volkov
2015-12-21 20:33 ` Roman Volkov
2015-12-22 9:09 ` Alexey Charkov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1450650492-18996-5-git-send-email-v1ron@mail.ru \
--to=v1ron@mail.ru \
--cc=daniel.lezcano@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@prisktech.co.nz \
--cc=rvolkov@v1ros.org \
--cc=tglx@linutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®