[PATCH 1/2] Documentation: dt: reset: Add syscon reset binding

["Andrew F. Davis" <afd@ti.com>]

Add syscon reset controller binding. This will hook to the reset
framework and use syscon/regmap to set reset bits. This allows
reset control of individual SoC subsytems and devices with
memory-mapped reset registers in a common register memory
space.

Signed-off-by: Andrew F. Davis <afd@ti.com>
[s-anna@ti.com: revise the binding format]
Signed-off-by: Suman Anna <s-anna@ti.com>
---
 .../devicetree/bindings/reset/syscon-reset.txt     | 84 ++++++++++++++++++++++
 1 file changed, 84 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/reset/syscon-reset.txt

diff --git a/Documentation/devicetree/bindings/reset/syscon-reset.txt b/Documentation/devicetree/bindings/reset/syscon-reset.txt
new file mode 100644
index 0000000..466378a
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/syscon-reset.txt
@@ -0,0 +1,84 @@
+SysCon Reset Controller
+=======================
+
+Almost all SoCs have hardware modules that require reset control in addition
+to clock and power control for their functionality. The reset control is
+typically provided by means of memory-mapped I/O registers. These registers are
+sometimes a part of a larger register space region implementing various
+functionalities. This register range is best represented as a syscon node to
+allow multiple entities to access their relevant registers in the common
+register space.
+
+A SysCon Reset Controller node defines a device that uses a syscon node
+and provides reset management functionality for various hardware modules
+present on the SoC.
+
+SysCon Reset Controller Node
+============================
+Each of the reset provider/controller nodes should have the following
+properties.
+
+Required properties:
+--------------------
+ - compatible	: Should be "syscon-reset"
+ - syscon	: phandle to the syscon node containing the reset registers
+ - #reset-cells	: Should be 6. Please see the reset consumer node below for
+                  usage details
+
+SysCon Reset Consumer Nodes
+===========================
+Each of the reset consumer nodes should have the following properties,
+in addition to their own properties.
+
+Required properties:
+--------------------
+ - resets	: A phandle and reset specifier pair, one pair for each reset
+		  signal that affects the device, or that the device manages.
+		  The phandle should point to the syscon node containing the
+		  reset registers, and the reset specifier should have 6
+		  cell-values. The reset specifier contains two similar pairs
+		  of 3 cell-values each, the first of the pair containing the
+		  reset control register information, and the second of the pair
+		  containing the reset status register information. The reset
+		  control and status registers can be same on some devices/SoCs.
+
+		  Each of the pairs of 3 cell-values should have the following
+		  values:
+		     Cell #1 : register offset of the reset control/status
+		               register from the syscon register base
+		     Cell #2 : bit shift value for the reset in the respective
+		               reset control/status register
+		     Cell #3 : polarity of the reset bit. Should be 1 for resets
+		               that are asserted when the bit is set, 0 for
+		               resets that are asserted when the bit is cleared
+
+Please also refer to Documentation/devicetree/bindings/reset/reset.txt for
+common reset controller usage by consumers.
+
+
+Example:
+--------
+The following example demonstrates a syscon node, the reset controller node
+using the syscon node, and a consumer (a DSP device) on the TI Keystone 2
+Hawking SoC.
+
+/ {
+	soc {
+		psc: power-sleep-controller@02350000 {
+			compatible = "syscon";
+			reg = <0x02350000 0x1000>;
+		};
+
+		pscrst: psc-reset {
+			compatible = "syscon-reset";
+			syscon = <&psc>;
+			#reset-cells = <6>;
+		};
+
+		dsp0: dsp0 {
+			...
+			resets = <&pscrst 0xa3c 8 0 0x83c 8 0>;
+			...
+		};
+	};
+};
-- 
2.7.0