mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Paul Burton <paul.burton@imgtec.com>
To: <linux-mips@linux-mips.org>, Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>, <netdev@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>
Subject: [PATCH v2 3/6] net: pch_gbe: Pull PHY GPIO handling out of Minnow code
Date: Wed, 3 Feb 2016 12:02:41 +0000	[thread overview]
Message-ID: <1454500964-6256-4-git-send-email-paul.burton@imgtec.com> (raw)
In-Reply-To: <1454500964-6256-1-git-send-email-paul.burton@imgtec.com>

The MIPS Boston development board uses the Intel EG20T Platform
Controller Hub, including its gigabit ethernet controller, and requires
that its RTL8211E PHY be reset much like the Minnow platform. Pull the
PHY reset GPIO handling out of Minnow-specific code such that it can be
shared by later patches.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
---

Changes in v2: None

 drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.h    |  4 ++-
 .../net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c   | 33 +++++++++++++++-------
 2 files changed, 26 insertions(+), 11 deletions(-)

diff --git a/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.h b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.h
index 2a55d6d..884f90b 100644
--- a/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.h
+++ b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.h
@@ -582,15 +582,17 @@ struct pch_gbe_hw_stats {
 
 /**
  * struct pch_gbe_privdata - PCI Device ID driver data
+ * @phy_reset_gpio:		PHY reset GPIO descriptor.
  * @phy_tx_clk_delay:		Bool, configure the PHY TX delay in software
  * @phy_disable_hibernate:	Bool, disable PHY hibernation
  * @platform_init:		Platform initialization callback, called from
  *				probe, prior to PHY initialization.
  */
 struct pch_gbe_privdata {
+	struct gpio_desc *phy_reset_gpio;
 	bool phy_tx_clk_delay;
 	bool phy_disable_hibernate;
-	int (*platform_init)(struct pci_dev *pdev);
+	int (*platform_init)(struct pci_dev *, struct pch_gbe_privdata *);
 };
 
 /**
diff --git a/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c
index fde4c11..23d28f0 100644
--- a/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c
+++ b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c
@@ -360,6 +360,16 @@ static void pch_gbe_mac_mar_set(struct pch_gbe_hw *hw, u8 * addr, u32 index)
 	pch_gbe_wait_clr_bit(&hw->reg->ADDR_MASK, PCH_GBE_BUSY);
 }
 
+static void pch_gbe_phy_set_reset(struct pch_gbe_hw *hw, int value)
+{
+	struct pch_gbe_adapter *adapter = pch_gbe_hw_to_adapter(hw);
+
+	if (!adapter->pdata || !adapter->pdata->phy_reset_gpio)
+		return;
+
+	gpiod_set_value(adapter->pdata->phy_reset_gpio, value);
+}
+
 /**
  * pch_gbe_mac_reset_hw - Reset hardware
  * @hw:	Pointer to the HW structure
@@ -2627,7 +2637,14 @@ static int pch_gbe_probe(struct pci_dev *pdev,
 	adapter->hw.reg = pcim_iomap_table(pdev)[PCH_GBE_PCI_BAR];
 	adapter->pdata = (struct pch_gbe_privdata *)pci_id->driver_data;
 	if (adapter->pdata && adapter->pdata->platform_init)
-		adapter->pdata->platform_init(pdev);
+		adapter->pdata->platform_init(pdev, pdata);
+
+	if (adapter->pdata && adapter->pdata->phy_reset_gpio) {
+		pch_gbe_phy_set_reset(&adapter->hw, 1);
+		usleep_range(1250, 1500);
+		pch_gbe_phy_set_reset(&adapter->hw, 0);
+		usleep_range(1250, 1500);
+	}
 
 	adapter->ptp_pdev = pci_get_bus_and_slot(adapter->pdev->bus->number,
 					       PCI_DEVFN(12, 4));
@@ -2715,7 +2732,8 @@ err_free_netdev:
 /* The AR803X PHY on the MinnowBoard requires a physical pin to be toggled to
  * ensure it is awake for probe and init. Request the line and reset the PHY.
  */
-static int pch_gbe_minnow_platform_init(struct pci_dev *pdev)
+static int pch_gbe_minnow_platform_init(struct pci_dev *pdev,
+					struct pch_gbe_privdata *pdata)
 {
 	unsigned long flags = GPIOF_DIR_OUT | GPIOF_INIT_LOW |
 		GPIOF_EXPORT | GPIOF_ACTIVE_LOW;
@@ -2724,16 +2742,11 @@ static int pch_gbe_minnow_platform_init(struct pci_dev *pdev)
 
 	ret = devm_gpio_request_one(&pdev->dev, gpio, flags,
 				    "minnow_phy_reset");
-	if (ret) {
+	if (!ret)
+		pdata->phy_reset_gpio = gpio_to_desc(gpio);
+	else
 		dev_err(&pdev->dev,
 			"ERR: Can't request PHY reset GPIO line '%d'\n", gpio);
-		return ret;
-	}
-
-	gpio_set_value(gpio, 1);
-	usleep_range(1250, 1500);
-	gpio_set_value(gpio, 0);
-	usleep_range(1250, 1500);
 
 	return ret;
 }
-- 
2.7.0

  parent reply	other threads:[~2016-02-03 12:03 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-02-03 12:02 [PATCH v2 0/6] pch_gbe fixes for Imagination Technologies MIPS Boston Paul Burton
2016-02-03 12:02 ` [PATCH v2 1/6] net: pch_gbe: Allow build on MIPS platforms Paul Burton
2016-02-03 12:02 ` [PATCH v2 2/6] net: pch_gbe: Mark Minnow PHY reset GPIO active low Paul Burton
2016-02-03 12:02 ` Paul Burton [this message]
2016-02-03 14:36   ` [PATCH v2 3/6] net: pch_gbe: Pull PHY GPIO handling out of Minnow code kbuild test robot
2016-02-03 12:02 ` [PATCH v2 4/6] net: pch_gbe: Always reset PHY along with MAC Paul Burton
2016-02-03 12:02 ` [PATCH v2 5/6] net: pch_gbe: Add device tree support Paul Burton
2016-02-03 12:02 ` [PATCH v2 6/6] net: pch_gbe: Allow longer for resets Paul Burton
2016-02-03 16:51   ` David Laight

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1454500964-6256-4-git-send-email-paul.burton@imgtec.com \
    --to=paul.burton@imgtec.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mips@linux-mips.org \
    --cc=netdev@vger.kernel.org \
    --cc=ralf@linux-mips.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®